Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Inexpensive

The technology is fast and inexpensive to apply nothing is used up tuid no contact is needed,... [Pg.274]

In order to be able to reduce prices, even more and more test- and measurement systems are integrated on PC-boards. The powerful and inexpensive PC eomponents can be directly u.sed for these (virtual) instruments. The limited dimensions of the PC boards require a reduction to the absolute necessity of the electronic components. Analogue signal proeessing must carried out by software as far as possible. [Pg.855]

A suggested middle ground is a quality server provider who can deliver the features you need Load your pages on the Server and get your own domain, "www.eompany.com", that means you operate a virtual server Your presence is then quick and inexpensive to achieve. You also remain flexible and independent, so can always transfer to another server if you decide to change providers for any reason. [Pg.978]

This method suffers from two disadvantages. Since it measures 7 or changes in 7 rather than t directly, temperature drifts or adventitious impurities can alter 7 and be mistakenly attributed to changes in film pressure. Second, while ensuring that zero contact angle is seldom a problem in the case of pure liquids, it may be with film-covered surfaces as film material may adsorb on the slide. This problem can be a serious one roughening the plate may help, and some of the literature on techniques is summarized by Gaines [69]. On the other hand, the equipment for the Wilhelmy slide method is simple and inexpensive and can be just as accurate as the film balance described below. [Pg.114]

There are many large molecules whose mteractions we have little hope of detemiining in detail. In these cases we turn to models based on simple mathematical representations of the interaction potential with empirically detemiined parameters. Even for smaller molecules where a detailed interaction potential has been obtained by an ab initio calculation or by a numerical inversion of experimental data, it is usefid to fit the calculated points to a functional fomi which then serves as a computationally inexpensive interpolation and extrapolation tool for use in fiirtlier work such as molecular simulation studies or predictive scattering computations. There are a very large number of such models in use, and only a small sample is considered here. The most frequently used simple spherical models are described in section Al.5.5.1 and some of the more common elaborate models are discussed in section A 1.5.5.2. section Al.5.5.3 and section Al.5.5.4. [Pg.204]

Another approach to mass analysis is based on stable ion trajectories in quadnipole fields. The two most prominent members of this family of mass spectrometers are the quadnipole mass filter and the quadnipole ion trap. Quadnipole mass filters are one of the most connnon mass spectrometers, being extensively used as detectors in analytical instnunents, especially gas clnomatographs. The quadnipole ion trap (which also goes by the name quadnipole ion store, QUISTOR , Paul trap, or just ion trap) is fairly new to the physical chemistry laboratory. Its early development was due to its use as an inexpensive alternative to tandem magnetic sector and quadnipole filter instnunents for analytical analysis. It has, however, staned to be used more in die chemical physics and physical chemistry domains, and so it will be described in some detail in this section. [Pg.1339]

One of the first cluster embedding schemes was put forth by Ellis and co-workers [172]. They were interested in studying transition metal impurities in NiAl alloys, so they considered a TMAl cluster embedded in a periodic self-consistent crystal field appropriate for bulk p -NiAl. The field was calculated via calculations, as was the cluster itself The idea was to provide a relatively inexpensive alternative to supercell DET calculations. [Pg.2225]

Slurry or slip casting provides a relatively inexpensive way to fabricate unifonn-thickness, thin-wall, or large cross section shapes [4o, 44, 45, 46, 42 aiid 48]. For slip casting, a slurry is first poured into a porous mould. Capillary suction then draws the liquid from the slurry to fonn a higher solids content, close-packed, leather-hard cast on the inner surface of the mould. In a fixed time, a given wall thickness is fonned, after which the excess slurry is drained. [Pg.2766]

For this purpose the simple and inexpensive atmospheric y desiccator (Fig. 9(A)) is fre-quently used the drying... [Pg.19]

Zienkiewicz, O. C. et al, 1985. Iterative method for constrained and mixed approximation, an inexpensive improvement to f.e.m. performance. Comput. Methods Appl. Meek Eng. 51, 3-29. [Pg.110]

Anexcollent and inexpensive hotair drier (" A.M. Industrial Type Blower ) is manu factored by Bylock lilectric Ltd., Ponders End, Enfield. Middlesex. [Pg.55]

Numerous forms are available, but these are generally expensive. A simple, efficient but inexpensive shaking machine, which can easily be constructed by a competent... [Pg.69]

The comparatively inexpensive long-scale thermometer, widely used by students, is usually calibrated for complete immersion of the mercury column in the vapour or liquid. As generally employed for boiling point or melting point determinations, the entire column is neither surrounded by the vapour nor completely immersed in the liquid. The part of the mercury column exposed to the cooler air of the laboratory is obviously not expanded as much as the bulk of the mercury and hence the reading will be lower than the true temperature. The error thus introduced is not appreciable up to about 100°, but it may amount to 3-5° at 200° and 6-10° at 250°. The error due to the column of mercury exposed above the heating bath can be corrected by adding a stem correction, calculated by the formula ... [Pg.72]

The so-called hydro-vac pump, shown in Fig. 11, 22, 2 (the upper half of the mercury reservoir and the column above it are insulated by a layer of asbestos), is an inexpensive, all-glass, mercury diffusion pump, which can be used in series either with an oil pmnp or with a water Alter pmnp (compare Fig. 11,21, 1) capable of producing a vacuum of at least 2 mm. It is accordingly of particular value in the organic laboratory for vacuum distillations, fractionations, sublimations and pyrolyses as well as for molecular distillations (see Section 11,26). The hydro-vac... [Pg.111]

Anhydrous magnesium sulphate. This is an excellent, neutral desiccating agent and is inexpensive. It is rapid in its action, chemically inert and fairly efficient, and can be employed for most compounds including those (esters, aldehydes, ketones, nitriles, amides, etc.) to which calcium chloride is not applicable. [Pg.140]

Reasonably pure solvents are required for many organic reactions and for recrystaUisations methods for obtaining these from commercial products will accordingly be described. Frequently, the pure solvent (e.g., the analytical reagent) can be purchased, but the cost is usually iiigh, particularly if comparatively large volumes are required. Furthermore, it is excellent practice for the student to purify inexpensive commercial solvents. [Pg.163]

Mono-alkyl ethers of ethylene glycol, ROCHjCHjOH. The mono methyl, ethyl and n-butyl ethers are inexpensive and are known as methyl cellosolve, cellosolve, and butyl cellosolve respectively. They are completely miscible with water, and are excellent solvents. The commercial products are purified by drying over anhydrous potassium carbonate or anhydrous calcium sulphate, followed by fractionation after... [Pg.170]

Ethyl acetate. Various grades of ethyl acetate are marketed. The anhydrous comjjound, b.p. 76-77°, is of 99 per cent, purity, is inexpensive, and is suitable for most purposes. The 95-98 per cent, grade usually contains some water, ethyl alcohol and acetic acid, and may be ptuified in the following manner. A mixture of 1 litre of the commercial ethyl acetate, 100 ml. of acetic anhydride and 10 drops of concentrated sulphuric acid is refluxed for 4 hours and then fractionated. The distU-late is shaken with 20-30 g. of anhydrous potassium carbonate, filtered and redistilled. The final product has a purity of about 99-7% and boils at 77°/760 mm. [Pg.174]

This preparation is an example of the use of di-M-butyl ether as a solvent in the Grignard reaction. The advantages are it is comparatively inexpensive, it can be handled without excessive loss due to evaporation, simple distillation gives an ether free from moisture and alcohol, and the vapour does not form explosive mixtures with air. n-Butyl ether cannot, of course, be employed when the boiling point of the neutral reaction product is close to 140°. [Pg.254]

Fumaric acid is conveniently prepared by the oxidation of the inexpensive furfural with sodium chlorate in the presence of a vanadium pentoxide catalyst ... [Pg.462]

Undecylenic acid (or 10-undecenoic acid) (I), a comparatively inexpensive commercial product obtained from castor oil, reacts with bromine in dry carbon tetrachloride to give 10 11-dibromoundecoic acid (II), which upon heating with a concentrated solution of potassium hydroxide yields 10-niidecynoic acid (III) ... [Pg.468]

Acetylation with acetic anhydride is comparatively expensive because of the cost of the reagent. The use of the inexpensive glacial acetic acid depends upon the displacement of the reversible equilibrium ... [Pg.576]


See other pages where Inexpensive is mentioned: [Pg.580]    [Pg.581]    [Pg.714]    [Pg.974]    [Pg.1015]    [Pg.703]    [Pg.1933]    [Pg.1947]    [Pg.2218]    [Pg.2353]    [Pg.2353]    [Pg.2702]    [Pg.2760]    [Pg.2764]    [Pg.2873]    [Pg.2891]    [Pg.2959]    [Pg.430]    [Pg.255]    [Pg.25]    [Pg.54]    [Pg.55]    [Pg.96]    [Pg.97]    [Pg.102]    [Pg.141]    [Pg.219]    [Pg.497]   
See also in sourсe #XX -- [ Pg.139 ]




SEARCH



Display technology, inexpensive

Inexpensive Raw Material

Inexpensive Surfactants

Inexpensive binders

Inexpensive carbon sources

Inexpensive colorants

Inexpensive filler

Inexpensive plasticizer

Inexpensive reagents

Inexpensive substrates

Nuclear power inexpensive energy

Redundant array of inexpensive disks,

Search for Inexpensive Carbon Substrates

© 2024 chempedia.info