Increased Efficiency

Further evidence for an increased efficiency of complexation in the presence of micellar aggregates with bivalent metal counterions is presented in Table 5.4. The apparent rate constants of the reaction of 5.1c with 5.2 in the presence of micelles of Co(DS)2, Ni(DS)2, Cu(DS)2 and Zn(DS)2 are compared to the rate constants for the corresponding bivalent metal ion - dienophile complexes in the absence of micelles. The latter data are not dependent on the efficiency of the formation of the catalyst - dienophile complex whereas possible incomplete binding will certainly be reflected in the former. The good correlations between 1 and and the absence of a correlation between and... 

The wisest fan choice is frequently not the cheapest fan. A small fan operates well on its curve but may not have adequate capacity for maximum flow control, future needs, or process upset conditions. It may be so lightly constmcted that it is operating near its peak speed with no provision for speed increases in the future, if needed. As fan size is increased, efficiency generally improves and wheel speed is lower. These factors decrease operating cost and provide reserve capacity for the future. However, it is also possible to oversize a fan and impair its performance. 

In summary, these second-generation gasifiers offer promise for the future in terms of increased efficiency as weU as for use of other feedstocks, such as biomass. The older, first-generation gasifiers, however, continue to be used. 

Viscosity (Viscosity-Index) Improvers. Oils of high viscosity index (VI) can be attained by adding a few percent of ahnear polymer similar to those used for pour-point depressants. The most common are polyisobutylenes, polymethacrylates, and polyalkylstyrenes they are used in the molecular weight range of about 10,000 to 100,000 (18). A convenient measure for the viscosity-increasing efficiency of various polymers is the intrinsic viscosity Tj, as given by the function... 

Whereas other metal salts, especially lead stearates and srdfates, or mixtures of Groups 2 and 12 carboxylates (Ba—Cd, Ba—Zn, Ca—Zn) ate also used to stabilize PVC, the tin mercaptides are some of the most efficient materials. This increased efficiency is largely owing to the mercaptans. The principal mechanism of stabilization of PVC, in which all types of stabilizers participate, is the adsorption of HCl, which is released by the PVC during degradation. This is important because the acid is a catalyst for the degradation, thus, without neutralization the process is autocatalytic. 

With the increasing emphasis on energy conservation and environmental considerations, additives for fuels that can correct combustion-related problems have aroused considerable interest. Many commercial fuel additives are combinations of organometaHics, dispersants, emulsifiers, and carrier solvents. The organometaHic, often a metal soap, acts as a combustion catalyst, increasing efficiency with reduction of smoke, deposits, and corrosion. 

Refitting of a tray-type column is desired to increase loading, increase efficiency, and/or decrease pressure drop. Structured packing is pariicularly applicable in this case. 

Other Cycle Steps A PSA cycle may have several other steps in addition to the basic adsorption, depressurization, and repressuriza-tion. Cocurrent depressurization, purge, and pressure-equalization steps are normally added to increase efficiency of separation and recoveiy of product. At the end of the adsorption step, the more weakly adsorbed species have been recovered as product, but there is still a significant amount held up in the bed in the inter- and intra-... 

For most large-scale processes, adsorbent particle size varies from 0.06 to 6 mm (0.0025 to 0.25 in), but the adsorbent packed in a fixed bed will have a fairly narrow particle size range. Pressure drop in adsorbers can be changed by changing the diameter to bed depth ratio and by changing the particle size (see Sec. 5). Adsorbent size also determines separation performance of adsorbent columns—increasing efficiency with decreasing particle size. In hquid-phase process-... 

A relationship of power consumption to collection efficiency is charac teristic of all particulate scrubbers. Attaining increased efficiency requires increased power consumption, and the power consumption required to attain a given efficiency increases as the particle size of the dust decreases. Experience generally indicates that the power consumption required to provide a specific efficiency on a given dust does not vary widely even with markedly different devices. The extent to which this generahzation holds true has not been fully explored, but the known extent is sufficient to suggest that the underlying collection mechanism may be essentially the same in all types of particulate scrubbers. 

Some investigators have proposed, mostly on the basis of mathematical modeling, to optimize the design of scrubbers to obtain a given efficiency with a minimum power consumption (e.g., Goel and Hollands, op. cit.). In fact, no optimum in performance appears to exist apart from some avoidable regions of unfavorable operation, increased contacting power yields increased efficiency. 

A wide variety of animal species are subjected to the administration of drugs during their lifetime.The various animal species can encounter drugs and other dietary additives by different routes and this is dependent on the environment in which they are kept. Intensively reared animals tend to have considerable consistency in the components of their diets and thus are much less likely to encounter the range of naturally produced compounds that extensively produced animals encounter. The desire for less expensive dietary constituents and increased efficiency of use has induced feed manufacturers and producers to add enzyme supplements to diets of most farmed animals to reduce the negative effects of indigestible dietary carbohydrates, refactory proteins and unavailable minerals such as phosphorus. This use of dietary additives to improve nutrient utilization and environmental consequences of feeding animals intensively has been the subject of intense research activity in the last five years. " The... 

In the case of nitrous acid plants, application of integrally geared process gas radial turbines and compressors are used in plants with capacities ranging from 120-600 t/day and higher. For air compression, up to three compressor stages are connected in series. To increase efficiency, the inlet temperature of the individual stages is reduced by using two external intermediate coolers. 

Lars Schibbye became chief engineer of SRM in 1950 and contributed to the technical advancement of the compressor. Most. significant was the invention of the asymmetric rotor profile, which was introduced commercially by Sullair in the U.S. in 1969. The asymmetric rotor profile reduces the leakage path area and sealing line length resulting in increased efficiency. 

The reduced adsorption capacity at ORVR vapor generation rates requires increased efficiency in the canister design, in order to limit the effect on cost and performance of the evaporative control system. 

Of obvious importance to aircraft is the smoothness of exterior surfaces. Smooth aerodynamic surfaces reduce aerodynamic drag, resulting in higher airspeeds and increased efficiency. Mechanical fasteners, even countersunk flush fasteners, introduce disruptions in the airflow over the exterior surface. Even the slight deformation of thin sheets around fasteners produces drag. Adhesively bonded structure has no fasteners to disrupt airflow and is more capable of producing the smooth continuous contours that are so common on aircraft. 

---