First measure

VARIABLES TO BE SUPPLIED ARRAY OF MEASURED INOEP VARIABLES ARRAY OF ERROR VARRIANCES CF INDEP VECTOR OF FIRST MEASURED DEPENDENT ERROR VARRIANCES OF FIRST VARIABLES... 

In summer 1998 the instrument will start with first measurements. 

A measurement procedure has been developed that allows to determine the mass of the inclusions as well as their locations with respect to radius, angle, and depth (2). For the depth determination use is made of the approximate 1/R dependence of the magnetic field strength from the distance R to the inclusion When in a first measurement at a small lift off an inclusion is detected, the measurement is repeated at an increased lift off From the signal ratio the depth can be calculated or seen from a diagram like fig. 5a which was generated experimentally. After that, from calibration curves like fig. 5b the absolute value of the signal leads to the mass of the inclusion. 

Measurement of the conductivity can be carried out to high precision with specially designed cells. In practice, tiiese cells are calibrated by first measuring the conductance of an accurately known standard, and then introducing the sample under study. Conductances are usually measured at about 1 kHz AC rather than with DC voltages in order to avoid complications arismg from electrolysis at anode and cathode [8]. 

The final technique addressed in this chapter is the measurement of the surface work function, the energy required to remove an electron from a solid. This is one of the oldest surface characterization methods, and certainly the oldest carried out in vacuo since it was first measured by Millikan using the photoelectric effect [4]. The observation of this effect led to the proposal of the Einstein equation ... 

We therefore conclude that the act of carrying out an experimental measurement disturbs the system in that it causes the system s wavefunction to become an eigenfunction of the operator whose property is measured. If two properties whose corresponding operators commute are measured, the measurement of the second property does not destroy knowledge of the first property s value gained in the first measurement. 

On the other hand, as detailed further in Appendix C, if the two properties (F and G) do not commute, the second measurement destroys knowledge of the first property s value. After the first measurement, P is an eigenfunction of F after the second measurement, it becomes an eigenfunction of G. If the two non-commuting operators properties are measured in the opposite order, the wavefunction first is an eigenfunction of G, and subsequently becomes an eigenfunction of F. 

After the first measurement is made (say for operator R), the wavefunetion beeomes an eigenfunetion of R with a well defined R-eigenvalue (say X) = /( i). 

Properties of steam can be divided iato thermodynamic, transport, physical, and chemical properties. In addition, the molecular stmcture and chemical composition of steam are of iaterest. It was at the start of iadustrialization, ca 1763, that thermodynamic relationships were first measured by Watt. A century later, ia 1859, Rankiae pubUshed his Manual of the Steam Engine, which gave a practical thermodynamic basis for the design and performance of steam engines. 

Statistical quality control is used to first measure and then continuously improve product quality. For example, The Dow Chemical Company s average 1989 performance compared to the typical sales specification were purity, = 99.65 wt % color, APHA = 4 acid (as HCl) = 7.3 ppm and water = 26 ppm. Averages of properties were based on rail car and tank tmck shipment samples during 1989. 

Tonnage of air emissions, water emissions and liquid and solid effluent and tonnage of hazardous materials released into the environment. These two measures are related to one another. However, the first measure relates the total effluent, including nonpolluting materials. The second measure looks only at the tonnage of hazardous materials contained in the total effluent. Both measures can be important indicators. For example, for solid waste it is important to know the total volume of material for disposal and different upstream treatment techniques may affect the total volume. However, for ozone depleting chemicals, only the quantity of these gases is important and other components such as water vapor may be irrelevant. 

Specific gravity is used to calculate the mass of crude oils and its products. Usually, crude oils and their liquid products are first measured on a volume basis, then changed to the corresponding masses using the specific gravity. 

The P.M.R. spectrum of an equilibrated aqueous solution of 2-deoxy-D-arafoino-hexopyranose was first measured by Lenz and Heeschen (37) who reported values for the chemical shifts of the anomeric protons and... 

The fluorescent lifetime of chlorophyll in vivo was first measured in 1957, independently by Brody and Rabinowitch (62) using pulse methods, and by Dmitrievskyand co-workers (63) using phase modulation methods. Because the measured quantum yield was lower than that predicted from the measured lifetime, it was concluded that much of the chlorophyll molecule was non-fluorescent, suggesting that energy transfer mechanisms were the means of moving absorbed energy to reactive parts of the molecule. 

During oxidation of the MoFe protein the P clusters are the first to be oxidized at about -340 mV. This redox potential was first measured (40) using Mossbauer spectroscopy and exhibited a Nemst curve consistent with a two-electron oxidation process. It is possibly low enough for this redox process to be involved in enzyme turnover (see Section V). No additional EPR signal was observed from this oxidized form at this time. However, later a weak signal near g = 12 was detected and was finally confirmed, using parallel mode EPR... 

The term "lag" refers to the delay in transporting heat from one part of the extruder to another. For example, "Lag 11" refers to the delay in heat conduction from the "OPl" heater to the first measurement, node number 5 ("Tn5"), in the model. Similarly, "Lag 12" refers to the delay in heat conduction from the "OPl" heater to the second measurement, node number 55 ("Tn55"), in the model. 

In cases where the mode of action is the strong or irreversible inhibition of an enzyme system, the assay may measure the extent of inhibition of this enzyme. This may be accomplished by first measuring the activity of the inhibited enzyme and then making comparison with the uninhibited enzyme. This practice is followed when studying acetylcholinesterase inhibition by organophosphates (OP). Acetylcholinesterase activity is measured in a sample of tissue of brain from an animal that has been exposed to an OP. Activity is measured in the same way in tissue samples from untreated controls of the same species, sex, age, etc. Comparison is then made between the two activity measurements, and the percentage inhibition is estimated. 

Records of Tests. Either of two methods may be used for recording routine test results. In the first, measurements and calculations are recorded in the individual worker s notebook and then transferred to the main record book. In the second method, a separate work book is kept for each routinely performed test. Whoever does the testing enters the results in the book and initials it. The pages should be lined with columns to suit each test s requirements. 

---