Fillers acidity

Several types of species can diffuse in and out of controlled drag delivery systems, including water, drag, water-soluble excipients (e.g., polymers, plasticizers, and/or fillers), acids, and bases from the environmental bulk fluid as well as polymer degradation products. Often, the polymeric material is chosen in such a way that drag diffusion through the macromolecular network is the rate-limiting step. In these cases, the systems... 

Glass-ionomer cements have taken a major place in dental treatments as restorative filling materials and also in a range of more adhesive applications due to their ability to bond to both dentine and composite fillers. Acid-etching techniques are well established for the bonding of resins to enamel. 

Zn " solutions by, e.g., NaOH. Occurs hydrated and loses water on heating. Dissolves in acids and in excess alkali (to give zincates). Used as rubber filler and as an absorbent in surgical dressings. 

Alkyds are formulated from polyester resins, cross-linking monomers, and fillers of mineral or glass. The unsaturated polyester resins used for thermosetting alkyds are the reaction products of polyfunctional organic alcohols (glycols) and dibasic organic acids. 

Acid-Base Behavior. The relative acidity-basicity of the filler, generally determined by measuring the pH value of a slurry of a specific mass of filler in 100 mL of deionized water, can influence the behavior of a filler in some systems. For example, the curing behavior of some elastomers is sensitive to the pH value of carbon black. 

Various other soft materials without the layer—lattice stmcture are used as soHd lubricants (58), eg, basic white lead or lead carbonate [598-63-0] used in thread compounds, lime [1305-78-8] as a carrier in wire drawing, talc [14807-96-6] and bentonite [1302-78-9] as fillers for grease for cable pulling, and zinc oxide [1314-13-2] in high load capacity greases. Graphite fluoride is effective as a thin-film lubricant up to 400°C and is especially useful with a suitable binder such as polyimide varnish (59). Boric acid has been shown to have promise as a self-replenishing soHd composite (60). 

The remaining tailings left over from the clay fractionation step is either flocculated with alum, high molecular weight polymers, or a weak (pH 3.0) solution of sulfuric acid, and stored in settling ponds as waste, or may be filtered and sold to the brick industry as a coating material. It also may be dried and sold as a filler in plastics and textured paint (qv). 

Dicylopentadiene Resins. Dicyclopentadiene (DCPD) can be used as a reactive component in polyester resins in two distinct reactions with maleic anhydride (7). The addition reaction of maleic anhydride in the presence of an equivalent of water produces a dicyclopentadiene acid maleate that can condense with ethylene or diethylene glycol to form low molecular weight, highly reactive resins. These resins, introduced commercially in 1980, have largely displaced OfXv o-phthahc resins in marine apphcations because of beneficial shrinkage properties that reduce surface profile. The inherent low viscosity of these polymers also allows for the use of high levels of fillers, such as alumina tfihydrate, to extend the resin-enhancing, fiame-retardant properties for apphcation in bathtub products (Table 4). 

Formulation. Polysulftde-based sealants are formulated with appropriate ingredients to obtain the desired properties for a particular appHcation. A typical formulation contains Hquid polysulftde polymer, curing agent, cure accelerators (bases) or retarders (acids), fillers, plasticizers, thixotropes, and adhesion promoters. 

Other blends such as polyhydroxyalkanoates (PHA) with cellulose acetate (208), PHA with polycaprolactone (209), poly(lactic acid) with poly(ethylene glycol) (210), chitosan and cellulose (211), poly(lactic acid) with inorganic fillers (212), and PHA and aUphatic polyesters with inorganics (213) are receiving attention. The different blending compositions seem to be limited only by the number of polymers available and the compatibiUty of the components. The latter blends, with all natural or biodegradable components, appear to afford the best approach for future research as property balance and biodegradabihty is attempted. Starch and additives have been evaluated ia detail from the perspective of stmcture and compatibiUty with starch (214). 

Fillers. Materials used as fillers (qv) in mbber can also be classified as acidic, basic, or neutral. Furnace blacks, ie, HAF, FEF, or SRF, are somewhat basic. As such, they can have an activating effect on sulfur cure rates. Furthermore, carbon blacks have been found to promote formation of mono/disulfide cross-links thereby helping minimize reversion and enhance aging properties. 

Recipe, in parts by wt smoked sheets, 100.00 zinc oxide, 5.00 filler, as indicated nondiscoloring antioxidant, 1.00 MBTS, 1.00 TMTD, 0.10 sulfur, 2.75 stearic acid, 3.00. 

---