Feedstock steam reforming

For many years, the overwhelming feedstock of choice for methanol producers has been natural As of 1990, some 75% of the world s methanol production capacity was based on a natural feedstock. Steam reforming with its low sulfur feed (typically, feeds to a reformer contain less than 0.1 ppmv total sulfur) makes synthesis that is particularly well suited to feed a loop containing Cu-Zn catalyst. With the advent of the low-pressure process (pressures of 10 MPa, 100 atm, or less), it became advantageous to feed gases to a loop that were not necessarily stoichiometric because of the overall reduction in compression requirements. 

Steam Reforming. When relatively light feedstocks, eg, naphthas having ca 180°C end boiling point and limited aromatic content, are available, high nickel content catalysts can be used to simultaneously conduct a variety of near-autothermic reactions. This results in the essentiaHy complete conversions of the feedstocks to methane ... 

Synthesis gas, a mixture of CO and o known as syngas, is produced for the oxo process by partial oxidation (eq. 2) or steam reforming (eq. 3) of a carbonaceous feedstock, typically methane or naphtha. The ratio of CO to may be adjusted by cofeeding carbon dioxide (qv), CO2, as illustrated in equation 4, the water gas shift reaction. 

Of the raw material hydrogen sources—natural gas, coal, and petroleum fractions—natural gas is the most often employed in ammonia plants in the 1990s and steam reforming is by far the most often used process. Partial oxidation processes are utilized where steam-reformable feeds are not available or in special situations where local conditions exist to provide favorable economics. Table 5 fists the contribution of the various feedstocks to world ammonia... 

Steam-Reforming Natural Gas. Natural gas is the single most common raw material for the manufacture of ammonia. A typical flow sheet for a high capacity single-train ammonia plant is iadicated ia Figure 12. The important process steps are feedstock purification, primary and secondary reforming, shift conversion, carbon dioxide removal, synthesis gas purification, ammonia synthesis, and recovery. 

Steam Reforming Processes. In the steam reforming process, light hydrocarbon feedstocks (qv), such as natural gas, Hquefied petroleum gas, and naphtha, or in some cases heavier distillate oils are purified of sulfur compounds (see Sulfurremoval and recovery). These then react with steam in the presence of a nickel-containing catalyst to produce a mixture of hydrogen, methane, and carbon oxides. Essentially total decomposition of compounds containing more than one carbon atom per molecule is obtained (see Ammonia Hydrogen Petroleum). 

Figure 8.3.1 is a typical process diagram for tlie production of ammonia by steam reforming. Tlie first step in tlie preparation of tlie synthesis gas is desulfurization of the hydrocarbon feed. Tliis is necessary because sulfur poisons tlie nickel catalyst (albeit reversibly) in tlie reformers, even at very low concentrations. Steam reforming of hydrocarbon feedstock is carried out in tlie priiiiiiry and secondary reformers. 

Naphtha could also serve as a feedstock for steam reforming units for... 

Extend Range of Feedstocks for the Process. Feedstock flexibility can enable maximum advantage to be taken of market fluctuations in the price and availability within the range of feedstocks which can be used. Obviously this is inappropriate in some cases where there is a close chemical link between feedstock and product, e.g. direct oxidation of ethylene to ethylene oxide, but in some processes, e.g. steam-reforming, flexibility is possible and may be advantageous. 

Steam reforming was developed in Germany at the beginning of the 20th century, to produce hydrogen for ammonia synthesis, and was further introduced in the 1930s when natural gas and other hydrocarbon feedstocks such as naphtha became available on a large scale. 

In the phosphoric acid fuel cell as currently practiced, a premium (hydrogen rich) hydrocarbon (e.g. methane) fuel is steam reformed to produce a hydrogen feedstock to the cell stack for direct (electrochemical) conversion to electrical energy. At the fuel electrode, hydrogen ionization is accomplished by use of a catalytic material (e.g. Pt, Pd, or Ru) to form solvated protons. 

Maximum theoretical yield of hydrogen produced by steam reforming (gasification) of different feedstocks. 

Most industrial hydrogen is manufactured by the following hydrocarbon-based oxidative processes steam reforming of light hydrocarbons (e.g., NG and naphtha), POx of heavy oil fractions, and ATR. Each of these technological approaches has numerous modifications depending on the type of feedstock, reactor design, heat input options, by-product treatment,... 

---