Examples precautions

Although isotope-dilution analysis can be very accurate, a number of precautions need to be taken. Some of these are obvious ones that any analytical procedure demands. For example, analyte preparation for both spiked and unspiked sample must be as nearly identical as possible the spike also must be intimately mixed with the sample before analysis so there is no differential effect on the subsequent isotope ration measurements. The last requirement sometimes requires special chemical treatment to ensure that the spike element and the sample element are in the same chemical state before analysis. However, once procedures have been set in place, the highly sensitive isotope-dilution analysis gives excellent precision and accuracy for the estimation of several elements at the same time or just one element. 

There is a significant difference in the toxicological effects of saturated and unsaturated afiphatic aldehydes. As can be seen in Table 6, the presence of the double bond considerably enhances toxicity. The precautions for handling reactive unsaturated aldehydes such as acrolein, methacrolein [78-85-3] and crotonaldehyde should be the same as those for handling other highly active eye and pulmonary irritants, as, for example, phosgene. 

Inhalation of certain fine dusts may constitute a health hazard. Eor example, exposure to siUca, asbestos, and beryllium oxide dusts over a period of time results ki the potential risk of lung disease. OSHA regulations specify the allowable levels of exposure to kigestible and respkable materials. Material Safety Data Sheets, OSHA form 20, available from manufacturers, provide information about hazards, precautions, and storage pertinent to specific refractory products. 

The toxicity of vanadium alloys may depend on other components in the alloy. For example, the V Ga alloy requires precautions related to both vanadium and gaUium, and gallium is highly toxic. Similarly, alloys with chromium may require precautions associated with that metal. 

Because pulp bleaching agents are, for the most part, reactive oxidising agents, appropriate precautions must be taken in their handling and use. For example, it is important to ensure that the threshold limit values (TLV) (20) in Table 2 are not exceeded in the workplace air. These are airborne concentrations in either parts per million by volume under standard ambient conditions or mg per cubic meter of air. They "represent conditions under which it is beUeved that nearly all workers may be repeatedly exposed, day after day, without adverse effect" (20). TWA refers to a time-weighted average for an 8-h workday STEL is a short-term exposure limit or maximum allowable concentration to which workers can be continuously exposed for 15 minutes. 

If the experiment is conducted in stages, precautions must be taken to ensure that possible differences between the stages do not invaUdate the results. Appropriate procedures to compare the stages must be included, both in the test plan and in the statistical analysis. For example, some standard test conditions, known as controls, may be included in each stage of the experiment. 

For flammable and/or toxic materials all of the precautions for a pressurized system should be considered. For example, when a centrifuge is pressurized, overpressure protection is required, even if the pressurization is an inert gas. Relieving of the pressure to a closed system or safe location must be considered. 

The procedure may be conducted on a larger scale in which case the proportion of catalyst and base are reduced. The submitters report that they obtained 169 g (78 ) of butyroin from 216.3 g (3.0 mol) of butyraldehyde, 26.8 (0.1 mol) of thiazolium catalyst, 60.6 g (0.6 mol) of triethylamlne, and 600 mL of absolute ethanol. Although the scale may be increased further, appropriate precautions should be taken to control the reaction. For example, the aldehyde may be added in portions or the flask may be cooled initially. 

The precautions naturally vary in each case. For example, to avoid improper admixture of chemicals will require ... 

In the laboratory, a range of slush baths may be used for speciality work. These are prepared by cooling organic liquids to their melting points by the addition of liquid nitrogen. Common examples are given in Table 8.2. Unless strict handling precautions are instituted, it is advisable to replace the more toxic and flammable solvents by safer alternatives. 

In situations in which piping protrudes partitions or bulkheads of dissimilar metals, proper precautions should be taken against galvanic corrosion. Possible solutions include the use of dielectric gaskets or sleeves and the use of plastic adhesive tapes. Examples are illustrated in Figure 2.6. 

It is important to exclude air in all hydrazone-type reductions involving olefins (otherwise, over-reduction occurs due to diimide formation) in the above example, as an added precaution cyclohexene was used as a solvent. 

As vent collection systems normally contain vapor/air mixtures, they are inherently unsafe. They normally operate outside the flammable range, and precautions are taken to prevent them from entering it, but it is difficult to think of everything that might go wrong. For example, an explosion occurred in a system that collected flarmnable vapor and air from the vents on a number of tanks and fed the mixture into a furnace. The system was designed to run at 10% of the lower explosion limit, but when the system was isolated in error, the vapor concentration rose. When the flow was restored, a plug of rich gas was fed into the furnace, where it mixed with air and exploded [17]. Reference 34 describes ten other incidents. 

Errors also occur because people deliberately decide not to carry out instructions that they consider unnecessary or incorrect. These are called violations. For example, they may not wear all the protective clothing or take the other precautions specified on a permit-to-w ork, as discussed in Section 1.4.2. We should ask the following questions both before and after accidents of this type ... 

Usually the constants involved in these cross terms are not taken to depend on all the atom types involved in the sequence. For example the stretch/bend constant in principle depends on all three atoms. A, B and C. However, it is usually taken to depend only on the central atom, i.e. = k , or chosen as a universal constant independent of atom type. It should be noted that cross tenns of the above type are inherently unstable if the geometry is far from equilibrium. Stretching a bond to infinity, for example, will make str/bend go towards — oo if 0 is less than If the bond stretch energy itself is harmonic (or quartic) this is not a problem as it approaches +oo faster, however, if a Morse type potential is used, special precautions will have to be made to avoid long bonds in geometry optimizations and simulations. 

---