Engineering evaluation

R. A. Baranescu, "Pumigation of Alcohols in a Multicylinder Diesel Engine Evaluation of Potential," SAE Paper 860308, SAE Int. Congress and Expo. (Detroit, Mich., Peb. 24—28, 1986) Society of Automotive Engineers, Warrendale, Pa. 

AGNS Staff, Engineering Evaluations of alternativesfor Processing Uranium-Based Fuels, Studies and Research Concerning the Barnwell Nuclear Fuels Plant (BNFP), AGNS-1040-3.1-32, National Technical Information Service (NTlS), Springfield, Va., 1978. 

Eignite to Methanol An Engineering Evaluation ofWinklerGasification and JCJ Methanol Gasification Route, AP-1392, Electric Power Research Institute,... 

An engineering evaluation should then be made of the worst-case... 

A few collections of more generic information as to the overall acid and alkali resistance of broad classes of materials remain. These are only intended to be used as indicators of the tendencies of these MOC to react they are not included as a substitute for the application of good, sound engineering evaluations. 

The development of a quantitative estimate of risk based on engineering evaluation and mathematical techniques for combining estimates of incident consequences and frequencies... 

Engineering evaluation has become extremely important to the SNG from Coal subprogram because of the need to critically assess the technical and/or economic impacts of the research projects being funded. In order to select processes having a greater potential for technical and/or economic advantages over other processes at the earliest possible time and to maximize prioritization within the SNG from Coal subprogram, increased efforts in... 

Rinaldi, Engineering Evaluation on Non-Reserve Zinc-Air Cells , ECOM 3528 (1972) 14) C.A. Nordell, Limiting Factors for Zinc-Air Batteries at Low and Elevated Temperatures , ECOM 3553 (1972) 15) J.W. Mellor, In-... 

Any comments which would help our engineers evaluate your requirements ... 

If it deems it necessary, the USEPA can require an expedited response action (ERA) at a site that would require an immediate engineering evaluation/ cost analysis (EE/CA). After a removal action is completed or determined unnecessary, the long-term remedial action must be undertaken. First, a remedial investigation/feasibility study (RI/FS) is performed to determine a proper course of action. This can involve ... 

Uses a 1986 GM V-block six-cylinder commercial engine. Evaluation criteria sludge, varnish, and viscosity changes. 

EPRI Report AF 741, "Process Engineering Evaluations of Alternate Coal Liquefaction Concepts". Final Report RP411-1, April 1978. 

Buckingham, P. A., et al., "Engineering Evaluation of Conceptual Coal Conversion Plant Using the H-Coal Liquefaction Process," EPRI Report, AF-1297 (1979). 

California Air Resources Board, Evaluation on a Woodwaste Fired Incinerator at Koppers Company, Orville, California, Test Report No. C-88-065, Engineering Evaluation Branch Monitoring and Laboratory Division, CARB, May 29, 1990. 

An engineering evaluation should then be made of the worst-case consequences, with the goal that the plant will be safe even if the worst case occurs. A HAZOP study could be used to help accomplish worst-case thinking. When the process designers know what the worst-case conditions are, they should ... 

An engineering evaluation should then be made of the worst case consequences with the goal that the plant will be safe even if the worst case occurs. When the process designers know what the worst case conditions are, they should try to avoid worst case conditions, be sure adequate redundancy of safety systems exists, and identify and implement lines of defense. These lines of defense could be preventive measures, corrective measures or sometimes as a last resort, containment or possibly abandonment of the process if the hazard is unacceptable. It is important to note that the worst case should be something that is realistic, not something that is conceivable but extremely unlikely. 

Developing a pollution control system involves an engineering evaluation of several factors which encompass a complete system. These include investigation of the pollution source, determining the properties of the pollution emissions, design of the collection and transfer systems, selection of the control device, and dispersion of the exhaust to meet applicable regulations. 

Various types of engineering evaluation, both field and laboratory, are required to establish engineering properties of the mixes made with... 

---