Electrochemical techniques polarization measurements

This set of experiments has focused on the use of two nondestructive electrochemical techniques to measure polarization resistance and thereby estimate the corrosion rate. In addition, the effects of scan rate and uncompensated ohmic resistance were studied. Three main points should have been made by this lab (1) Uncompensated ohmic resistance is always present and must be measured and taken into account before Rp values can be converted into corrosion rates, otherwise an overestimation of Rv will result. This overestimate of Rp leads to an underestimate of corrosion rate, with the severity of this effect dependent upon the ratio Rp/Ra. (2) Finite scan rates result in current shunted through the interfacial capacitance, thereby decreasing the observed impedance and overestimating the corrosion rate. (3) Both of these errors can be taken into account by measuring Ra via EIS or current interruption and by using a low enough scan rate as indicated by an EIS measurement in order to force the interfacial capacitance to take on very large impedance values in comparison to Rp. 

This set of experiments has focused on the use of two nondestructive electrochemical techniques to measure polarization resistance and thereby estimate the corrosion rate. In addition, the effects of scan rate and uncompensated ohmic resistance were studied. Three main points should have been made by this lab ... 

Calculation of corrosion rate from the corrosion current Electrochemical Techniques to Measure Polarization Resistance... 

The electrochemical technique of measuring the relationship between current and electrode potential (polarization curve) is widely used to help understand corrosion behavior. Polarization curves are easily obtained by potentiodynamic methods. The polarization curve is a graphical representation of the dependence of current density (horizontal axis) on electrode potential (vertical axis), and the gradient of the curve is... 

To obtain the corrosion current from Rp, values for the anodic and cathodic slopes must be known or estimated. ASTM G59 provides an experimental procedure for measuring Rp. A discussion or the factors which may lead to errors in the values for Rp, and cases where Rp technique cannot be used, are covered by Mansfeld in Polarization Resistance Measurements—Today s Status, Electrochemical Techniques for Corrosion Engineers (NACE International, 1992). 

Other electrochemical techniques covered include measurements of the corrosion potential, the redox potential, the polarization resistance, the electrochemical impedance, electrochemical noise, and polarization curves, including pitting scans. A critical review of the literature concerned with the application of electrochemical techniques in the study of MIC is available [1164]. 

In the previous section, we demonstrated the micrometer droplet size dependence of the ET rate across a microdroplet/water interface. Beside ET reactions, interfacial mass transfer (MT) processes are also expected to depend on the droplet size. MT of ions across a polarized liquid/liquid interface have been studied by various electrochemical techniques [9-15,87], However, the techniques are disadvantageous to obtain an inside look at MT across a microspherical liquid/liquid interface, since the shape of the spherical interface varies by the change in an interfacial tension during electrochemical measurements. Direct measurements of single droplets possessing a nonpolarized liquid/liquid interface are necessary to elucidate the interfacial MT processes. On the basis of the laser trapping-electrochemistry technique, we discuss MT processes of ferrocene derivatives (FeCp-X) across a micro-oil-droplet/water interface in detail and demonstrate a droplet size dependence of the MT rate. 

The direct electrochemical measurement of such low corrosion rates is difficult and limited in accuracy. However, electrochemical techniques can be used to establish a database against which to validate rates determined by more conventional methods (such as weight change measurements) applied after long exposure times. Blackwood et al. (29) used a combination of anodic polarization scans and open circuit potential measurements to determine the dissolution rates of passive films on titanium in acidic and alkaline solutions. An oxide film was first grown by applying an anodic potential scan to a preset anodic limit (generally 3.0 V), Fig. 24, curve 1. Subsequently, the electrode was switched to open-circuit and a portion of the oxide allowed to chemically dissolve. Then a second anodic... 

The methods of measuring corrosion rates in the course of testing corrosion inhibitors are conventional weight loss, electrochemical techniques such as linear polarization resistance, potentiodynamic polarization, AC impedance, and electrochemical potential or current noise. 

Potentiodynamic polarization measurement is an effective electrochemical technique in characterizing film formed on a metal surface under various redox conditions. The electrochemical polarization measurements were... 

Conductometry is an electrochemical technique used to determine the quantity of an analyte present in a mixture by measurement of its effect on the electrical conductivity of the mixture. It is the measure of the ability of ions in solution to carry current under the influence of a potential difference. In a conductometric cell, potential is applied between two inert metal electrodes. An alternating potential with a frequency between 100 and 3000 Hz is used to prevent polarization of the electrodes. A decrease in solution resistance results in an increase in conductance and more current is passed between the electrodes. The resulting current flow is also alternating. The current is directly proportional to solution conductance. Conductance is considered the inverse of resistance and may be expressed in units of ohm (siemens). In clinical analysis, conductometry is frequently used for the measurement of the volume fraction of erythrocytes in whole blood (hematocrit) and as the transduction mechanism for some biosensors. 

Since the Co(II) to Co(III) complexes were redox active, an electrochemical method of analysis seemed viable for the quantification of the two species in the reaction. The specific electrochemical technique developed to monitor the activation reaction allowed the simultaneous quantitative measurement of (salen)Co(II) and (salen)Co(III) species in the medium. The principle of the method is based on the electro-oxidation of both species on a platinum-rotating electrode linearly polarized with respect to a standard electrode [7]. The electrochemical reactions operative with this cyclic voltammetry technique involve the single electron oxidation of each species and occur at the revolving surface of the electrode. With this salen ligand system, the Co(II) to Co(III) transformation was determined as being fully reversible, while the Co(III) to Co(IV) reaction was irreversible. 

The electrochemical techniques described in Sects. 7.3.1 and 7.3.2 measure the response of the system to an externally applied perturbation. It is possible to use the inherent noise in the system as a stimulus and measme the system response [27-36]. The fundamental basis to use noise analysis as a determination of corrosion rate is not as strong as that for the other techniques. However, the advantage of noise analysis is that there is no need to apply any external signal, and the system is not polarized at all away from its natural... 

F. Mansfeld, Polarization resistance measurements—experimental procedure and evaluation of test data, in R. Baboian (Ed.), Electrochemical Techniques for Corrosion Engineering, NACE, Houston, 1977, p. 67. 

Several electrochemical and physical methods can be used to measure the corrosion rate of the system. Some of the commonly used methods are listed in Table 15.6. The use of these electrochemical tools in monitoring the corrosion rate of cathodicaUy protected structures was reviewed by several researchers [75—80]. More information and the scope of corrosion rate measurements of cathodicaUy polarized metal structures by electrochemical techniques can be obtained in the reviews by Jankowski [81,82]. 

---