Potentiometric electrochemical cell

Measurements on electrochemical cells Potentiometric titrations pH measurements ( 0.1 pH unit) pH measurements ( 0.01 pH unit) in measurement of blood pH and C02 tension... 

In potentiometry the potential of an electrochemical cell is measured under static conditions. Because no current, or only a negligible current, flows while measuring a solution s potential, its composition remains unchanged. For this reason, potentiometry is a useful quantitative method. The first quantitative potentiometric applications appeared soon after the formulation, in 1889, of the Nernst equation relating an electrochemical cell s potential to the concentration of electroactive species in the cell. ... 

Potentiometric measurements are made using a potentiometer to determine the difference in potential between a working or, indicator, electrode and a counter electrode (see Figure 11.2). Since no significant current flows in potentiometry, the role of the counter electrode is reduced to that of supplying a reference potential thus, the counter electrode is usually called the reference electrode. In this section we introduce the conventions used in describing potentiometric electrochemical cells and the relationship between the measured potential and concentration. 

Also, by convention, potentiometric electrochemical cells are defined such that the indicator electrode is the cathode (right half-cell) and the reference electrode is the anode (left half-cell). 

Potentiometric electrochemical cells are constructed such that one of the half-cells provides a known reference potential, and the potential of the other half-cell indicates the analyte s concentration. By convention, the reference electrode is taken to be the anode thus, the shorthand notation for a potentiometric electrochemical cell is... 

The potential of the indicator electrode in a potentiometric electrochemical cell is proportional to the concentration of analyte. Two classes of indicator electrodes are used in potentiometry metallic electrodes, which are the subject of this section, and ion-selective electrodes, which are covered in the next section. 

If the copper electrode is the indicator electrode in a potentiometric electrochemical cell that also includes a saturated calomel reference electrode... 

Membrane Potentials Ion-selective electrodes, such as the glass pH electrode, function by using a membrane that reacts selectively with a single ion. figure 11.10 shows a generic diagram for a potentiometric electrochemical cell equipped with an ion-selective electrode. The shorthand notation for this cell is... 

Equations 11.19-11.21 are defined for a potentiometric electrochemical cell in which the pH electrode is the cathode. In this case an increase in pH decreases the cell potential. Many pH meters are designed with the pH electrode as the anode so that an increase in pH increases the cell potential. The operational definition of pH then becomes... 

Scale of Operation Coulometric methods of analysis can be used to analyze small absolute amounts of analyte. In controlled-current coulometry, for example, the moles of analyte consumed during an exhaustive electrolysis is given by equation 11.32. An electrolysis carried out with a constant current of 100 pA for 100 s, therefore, consumes only 1 X 10 mol of analyte if = 1. For an analyte with a molecular weight of 100 g/mol, 1 X 10 mol corresponds to only 10 pg. The concentration of analyte in the electrochemical cell, however, must be sufficient to allow an accurate determination of the end point. When using visual end points, coulometric titrations require solution concentrations greater than 10 M and, as with conventional titrations, are limited to major and minor analytes. A coulometric titration to a preset potentiometric end point is feasible even with solution concentrations of 10 M, making possible the analysis of trace analytes. 

Electrochemical methods covered in this chapter include poten-tiometry, coulometry, and voltammetry. Potentiometric methods are based on the measurement of an electrochemical cell s potential when only a negligible current is allowed to flow, fn principle the Nernst equation can be used to calculate the concentration of species in the electrochemical cell by measuring its potential and solving the Nernst equation the presence of liquid junction potentials, however, necessitates the use of an external standardization or the use of standard additions. 

FIGURE 5-1 Schematic diagram of an electrochemical cell for potentiometric measurements. 

Potentiometric methods are based on the measurement of the potential of an electrochemical cell consisting of two electrodes immersed in a solution. Since the cell potential is measured under the condition of zero cmrent, usually with a pH/mV meter, potentiometry is an equilibrium method. One electrode, the indicator electrode, is chosen to respond to a particular species in solution whose activity or concentration is to be measured. The other electrode is a reference electrode whose half-cell potential is invariant. 

Fig. 5.41 C02-alarm system based on potentiometric electrochemical cells (STEINEL Solutions AG).

In this present book, we will look at the analytical use of two fundamentally different types of electrochemical technique, namely potentiometry and amper-ometry. The distinctions between the two are outlined in some detail in Chapter 2. For now, we will anticipate and say that a potentiometric technique determines the potential of electrochemical cells - usually at zero current. The potential of the electrode of interest responds (with respect to a standard reference electrode) to changes in the concentration of the species under study. The most common potentiometric methods used by the analyst employ voltmeters, potentiometers or pH meters. Such measurements are generally relatively cheap to perform, but can be slow and tedious unless automated. 

Let us revisit the electrochemical cell shown earlier in Figure 3.1. In this figure, two redox electrodes are immersed in solutions of their respective ions, with the half cells being connected by a salt bridge. If we were to connect an infinite-resistance voltmeter between the cells, then it would be possible to perform potentiometric experiments such as those described in the previous chapter. One electrode would be positive with respect to the other, with the separation in potential between the two electrodes being the emf - but only if the measurement was performed at equilibrium. (As before, we take the word equilibrium to imply that no charge flows.)... 

Solid electrolyte electrochemical cells can be operated in a variety of ways (the three modes of operation are illustrated schematically in Figure 2). Such a cell may be operated potentiometrically in order to investigate the behaviour of a catalyst of interest. This technique has become known as solid electrolyte potentiometry (SEP). The catalyst itself is deposited in the form of an electrode... 

The equivalent circuit corresponding to this interface is shown in Fig. 6.1b. The charge-transfer resistances for the exchange of sodium and chloride ions are very low, but the charge-transfer resistance for the polyanion is infinitely high. There is no direct sensing application for this type of interface. However, it is relevant for the entire electrochemical cell and to many practical potentiometric measurements. Thus if we want to measure the activity of an ion with the ion-selective electrode it must be placed in the same compartment as the reference electrode. Otherwise, the Donnan potential across the membrane will appear in the cell voltage and will distort the overall result. 

A potentiometric electrochemical cell consisting of a reference electrode, solid-state electrolyte(s), and an indicator electrode can provide information about the partial pressure of gas in the same way as the cells utilizing ion-selective electrodes and liquid electrolytes can. The general mechanism is as follows. A sample gas, which is part of a redox couple, permeates into the solid-state structure usually through the porous metal electrode and sets up a reversible potential difference at that interface according to the reaction... 

In Chapters 6 and 7, we discussed potentiometric and amperometric sensors, respectively. The third basic electrochemical parameter that can yield sensory information is the conductance of the electrochemical cell (Fig. 8.1). Conductance is the reciprocal of resistance. It is related to current and potential through the generalized form of Ohm s law (C.l). If the measurement is done with AC signal conductance (G) becomes frequency-dependent conductance G(co) and the resistance R becomes impedance Z( (o). 

Potentiometric measurements are based on the Nernst equation, which was developed from thermodynamic relationships and is therefore valid only under equilibrium (read thermodynamic) conditions. As mentioned above, the Nernst equation relates potential to the concentration of electroactive species. For electroanalytical purposes, it is most appropriate to consider the redox process that occurs at a single electrode, although two electrodes are always essential for an electrochemical cell. However, by considering each electrode individually, the two-electrode processes are easily combined to obtain the entire cell process. Half reactions of electrode processes should be written in a consistent manner. Here, they are always written as reduction processes, with the oxidised species, O, reduced by n electrons to give a reduced species, R ... 

Fig. 2.1. Schematic illustration of the galvanic electrochemical cell used to conduct potentiometric measurements. The disposable indicator electrode shown is fashioned from plastic pipette tips and PVC tubing. Note that the top compartment (shown dashed) is only necessary in cases where the inner filling solution does not contain well-defined concentrations of Cl" or Ag+.

Studies on ethanol trace detection in aqueous solutions were carried out in an electrochemical cell of peroxidase-mimetic sensor of the potentiometric type, consisting of a reference electrode (Ag/AgCl) and a biomimetic electrode. Redistilled water was used for the background solution. The biomimetic electrode was prepared by adhering hematin-containing meroxidase mimetic to aluminum foil with Pattex adhesive [7, 8],... 

While the redox titration method is potentiometric, the spectroelectrochemistry method is potentiostatic [99]. In this method, the protein solution is introduced into an optically transparent thin layer electrochemical cell. The potential of the transparent electrode is held constant until the ratio of the oxidized to reduced forms of the protein attains equilibrium, according to the Nemst equation. The oxidation-reduction state of the protein is determined by directly measuring the spectra through the tranparent electrode. In this method, as in the redox titration method, the spectral characterization of redox species is required. A series of potentials are sequentially potentiostated so that different oxidized/reduced ratios are obtained. The data is then adjusted to the Nemst equation in order to calculate the standard redox potential of the proteic species. Errors in redox potentials estimated with this method may be in the order of 3 mV. 

C. The potentiometric determination of pH The most advanced and precise method of the measurement of pH is based on the measurement of the electromotive force (e.m.f.) of an electrochemical cell, which contains the solution of the unknown pH as electrolyte, and two electrodes. The electrodes are connected to the terminals of an electronic voltmeter, most often called simply a pH-meter. If properly calibrated with a suitable buffer of a known pH, the pH of the unknown solution can be read directly from the scale. 

The three most common modes of operation of electrochemical detection are amperometric, coulometric, and potentiometric. An amperometric detector is an electrochemical cell that produces a signal proportional to the analyte concentration usually the percentage of the analyte that undergoes the redox reaction is very low, about 5%. 

---