Electrical properties bases

Fig. 10.13 l-V for Ta-AI-O-N compared to Ta-O, showing that Al improves the electrical properties (based on depositions in the same sputtering system). The composition of this film was about Ta0.8AI0.2O1.45N0.05 ... 

Thus far the importance of carbon cluster chemistry has been in the discovery of new knowl edge Many scientists feel that the earliest industrial applications of the fullerenes will be based on their novel electrical properties Buckminsterfullerene is an insulator but has a high electron affinity and is a superconductor in its reduced form Nanotubes have aroused a great deal of interest for their electrical properties and as potential sources of carbon fibers of great strength... 

Oxides. Although not widespread commercially, glass-ceramics consisting of various oxide crystals in a matrix of siUceous residual glass offer properties not available with mote common siUcate crystals. In particular, glass-ceramics based on spinels and perovskites can be quite refractory and can yield useful optical and electrical properties. 

Unsaturated resias based on 1,4-cyclohexanedimethanol are useful ia gel coats and ia laminating and molding resias where advantage is taken of the properties of very low water absorption and resistance to boiling water (6). Thermal stabiHty is imparted to molding resias, both thermoplastic (71,72) and thermoset (73—76), enabling retention of physical and electrical properties at elevated temperatures (77). Additionally, resistance to chemical and environmental exposure is characteristic of products made from these resias (78). 

Diffusion. Another technique for modifying the electrical properties of siUcon and siUcon-based films involves introducing small amounts of elements having differing electrical compositions, dopants, into substrate layers. Diffusion is commonly used. There are three ways dopants can be diffused into a substrate film (/) the surface can be exposed to a chemical vapor of the dopant at high temperatures, or (2) a doped-oxide, or (J) an ion-implanted layer can be used. Ion implantation is increasingly becoming the method of choice as the miniaturization of ICs advances. However, diffusion is used in... 

Paper-Base Grades. Grade X is primarily intended for mechanical apphcations where electrical properties are of secondary importance. It should be used with discretion when high humidity conditions are encountered and it is not equal to fabric-base grades in impact strength. 

For a part to exhibit stmctural stiffness, flexural moduH should be above 2000 N/mm (290,000 psi). Notched l2od impact values should be deterrnined at different thicknesses. Some plastics exhibit different notch sensitivities. For example, PC, 3.2 mm thick, has a notched l2od impact of 800 J/m (15 fdbf/in.) which drops to 100 J/m (1.9 fflbf/in.) at 6.4-mm thickness. On the other hand, one bisphenol A phthalate-based polyarylate resin maintains a 250-J /m (4.7-fdbf/in.) notched l2od impact at both thicknesses. Toughness depends on the stmcture of the part under consideration as well as the plastic employed to make the part. Mechanical properties, like electrical properties, ate also subject to thermal and water-content changes. 

Thermosetting compositions based on urea-formaldehyde are widely employed because of their low cost, wide colour range, rigidity and good electrical properties. 

Plastic Material First Introduced Strength Electrical Properties Acids Bases Oxidizing Agents Common Solvents Product Manufacturing Methods Common Applications... 

Most of the results presented in the previous chapters are based on idealized conditions. In practice, the performance of an electrostatic precipitator can be significantly influenced by the dust layers on discharge and collection electrodes i.e., dust layers may alter the electrical properties of the system. It is also possible that dust layers are not stable i.e., collected particles become loose, increasing the particle concentration in the outlet of the precipitator. These problems play a much smaller role if the surface collection electrode is continuously flushed with water. These wet elearostatic precipitators, however, cannot be used in all applications. 

Although it is required to refine the above condition I in actuality, this rather simple but impressive prediction seems to have much stimulated the experiments on the electrical-conductivity measurement and the related solid-state properties in spite of technological difficulties in purification of the CNT sample and in direct measurement of its electrical conductivity (see Chap. 10). For instance, for MWCNT, a direct conductivity measurement has proved the existence of metallic sample [7]. The electron spin resonance (ESR) (see Chap. 8) [8] and the C nuclear magnetic resonance (NMR) [9] measurements have also proved that MWCNT can show metallic property based on the Pauli susceptibility and Korringa-like relation, respectively. On the other hand, existence of semiconductive MWCNT sample has also been shown by the ESR measurement [ 10], For SWCNT, a combination of direct electrical conductivity and the ESR measurements has confirmed the metallic property of the sample employed therein [11]. More recently, bandgap values of several SWCNT... 

The methods dependent upon measurement of an electrical property, and those based upon determination of the extent to which radiation is absorbed or upon assessment of the intensity of emitted radiation, all require the use of a suitable instrument, e.g. polarograph, spectrophotometer, etc., and in consequence such methods are referred to as instrumental methods . Instrumental methods are usually much faster than purely chemical procedures, they are normally applicable at concentrations far too small to be amenable to determination by classical methods, and they find wide application in industry. In most cases a microcomputer can be interfaced to the instrument so that absorption curves, polarograms, titration curves, etc., can be plotted automatically, and in fact, by the incorporation of appropriate servo-mechanisms, the whole analytical process may, in suitable cases, be completely automated. 

Siloxane containing interpenetrating networks (IPN) have also been synthesized and some properties were reported 59,354 356>. However, they have not received much attention. Preparation and characterization of IPNs based on PDMS-polystyrene 354), PDMS-poly(methyl methacrylate) 354), polysiloxane-epoxy systems 355) and PDMS-polyurethane 356) were described. These materials all displayed two-phase morphologies, but only minor improvements were obtained over the physical and mechanical properties of the parent materials. This may be due to the difficulties encountered in controlling the structure and morphology of these IPN systems. Siloxane modified polyamide, polyester, polyolefin and various polyurethane based IPN materials are commercially available 59). Incorporation of siloxanes into these systems was reported to increase the hydrolytic stability, surface release, electrical properties of the base polymers and also to reduce the surface wear and friction due to the lubricating action of PDMS chains 59). 

---