Efficiency gross

Blanket energy multiplication Direct conversion efficiency Thermal conversion efficiency Gross electric power Injection system efficiency Power recirculated to injectors Power recirculated to copper coils Net electric power Recirculated power fraction System efficiency Direct capital cost... 

Table 1.5 Typical ranges of thermal efficiencies (gross) of modern thermal power plants (Pioro and Duffey, 2015 Pioro and Kirillov, 2013 Pioro, 2012)...

Table 11 Estimated ranges of thermal efficiencies (gross) of Generation-FV NPP concepts (Generation IV concepts are listed according to thermal efficiency decrease) (shown here just for reference purposes)... 

Gross heating value of biomass or methane. Conversion of biomass or methane to another biofuel requires that the process conversion efficiency be used to reduce the potential energy available. These figures do not include additional biomass from dedicated energy plantations. 

At least two manufacturers have developed and installed machines rated to produce more than 210 MW of electricity in the simple-cycle mode. In both cases, the machines were designed and manufactured through cooperative ventures between two or more international gas turbine developers. One 50-Hz unit, first installed as a peaking power faciUty in France, is rated for a gross output of 212 MW and a net simple-cycle efficiency of 34.2% for natural-gas firing. When integrated into an enhanced three-pressure, combined-cycle with reheat, net plant efficiencies in excess of 54% reportedly can be achieved. 

Combustion. The primary reaction carried out in the gas turbine combustion chamber is oxidation of a fuel to release its heat content at constant pressure. Atomized fuel mixed with enough air to form a close-to-stoichiometric mixture is continuously fed into a primary zone. There its heat of formation is released at flame temperatures deterruined by the pressure. The heat content of the fuel is therefore a primary measure of the attainable efficiency of the overall system in terms of fuel consumed per unit of work output. Table 6 fists the net heat content of a number of typical gas turbine fuels. Net rather than gross heat content is a more significant measure because heat of vaporization of the water formed in combustion cannot be recovered in aircraft exhaust. The most desirable gas turbine fuels for use in aircraft, after hydrogen, are hydrocarbons. Fuels that are liquid at normal atmospheric pressure and temperature are the most practical and widely used aircraft fuels kerosene, with a distillation range from 150 to 300 °C, is the best compromise to combine maximum mass —heat content with other desirable properties. For ground turbines, a wide variety of gaseous and heavy fuels are acceptable. 

For distillations, it is often of more interest to ascertain the effect of entrainment on efficiency than to predic t the quantitative amount of liquid entrained. For this purpose, the correlation shown in Fig. 14-26 is useful. The parametric curves in the figure represent approach to the entrainment flood point as measured or as predicted by Fig. 14-25 or some other flood correlation. The abscissa values are those of the flow parameter discussed earher. The ordinate values y are fractions of gross hquid downflow, defined as follows ... 

Since the exacd value of the hydraulic efficiency e, is never known, V/ can be taken as an approximation where e is the gross (hydraulic horsepower/brake horsepower) pump efficiency. Efficiencies of pump designs running as turbines are usually 5 to 10 efficiency points lower than those as pumps at the best efficiency point. 

Serth, R.W, B. Srikanth, and S.J. Maronga, Gross Error Detection and Stage Efficiency Estimation in a Separation Process, AlChE Journal, 39(10), 1993, 1726-1731. (Physical model development, parameter estimation)... 

When a molten plastic is forced through a die it is found that under certain conditions there will be defects in the extrudate. In the worst case this will take the form of gross distortion of the extrudate but it can be as slight as a dullness of the surface. In most cases flow defects are to be avoided since they affect the quality of the output and the efficiency of the processing operation. However, in some cases if the flow anomaly can be controlled and reproduced, it can be used to advantage - for example, in the production of sheets with matt surface finish. Flow defects result from a combination of melt flow properties, die design and processing conditions but the exact causes and mechanisms are not completely understood. The two most common defects are... 

For the entire economy, with its countless services and inputs, economists usually define the service or economics efficiency as the entire GDP (Gross Domestic Product) divided by E, the annual total primary energy used Economic Efficiency = GDP/E. 

Resulting net thickness must be corrected to gross or actual thickness by dividing by joint efficiency. 

The high hydrogen/carbon ratio of gas means that the quantity of water vapor in the products of combustion is greater than most other fossil fuels. The latent heat of this cannot be released in conventional appliances leading to a low net/gross ratio of calorific value of 90 per cent. (It is normal practice to quote gross CV in Europe net CV is often used. If net CV is quoted, efficiencies of over 190 per cent are possible.)... 

Condensing boilers are now available for both gas- and oil-fired plant, the advantage of these being that the flue gases are further cooled down to below 100°C so that the latent heat available in the flue gas water vapor is recovered. The condensate has to be removed and the boiler capital cost is higher than for conventional plant. However, the boiler plant efficiency is increased to the order of 90 per cent, based upon the fuel gross calorific value. Where the flue gas exit temperatures are in excess of 200° C a further economy can be obtained by the provision of a spray recuperator in the case of gas and flue gas economizers for oil and coal. 

The efficacy of polymers when used to protect metals from corrosive environments is influenced by their efficiency as barrier materials. When applied to metals by some techniques, such as fluidised bed coating, there is always the danger of macro-diffusion through pinholes which are gross imperfections in the surface and which do not have to be visible to be very much greater than the dimension of penetrating molecules. 

Fuels, especially coals, are ranked according to limits on fixed carbon, volatile matter, and calorific value. Typical gross heating values of some common fuels (based on approximately 80% fuel to steam efficiency) are listed here ... 

---