Diols polyurethane preparation

A novel chemoenzymatic route to polyester polyurethanes was developed without employing highly toxic isocyanate intermediates. First, diurethane diols were prepared from cyclic carbonates and primary diamines, which were subsequently polymerized with dicarboxylic acids and glycols by using lipase CA as catalyst, yielding the polyurethanes under mild reaction conditions. 

Owing to their improved stability towards hydrolysis and oxidation, dimer diol polyethers (and dimer diol polycarbonates) are used as soft segments in the preparation of thermoplastic polyurethanes. Polyurethanes prepared from such oleo-chemical building blocks are very hydrophobic and show the expected stability. 

In a recent patent, Reuter (110) describes a polyurethane prepared from PTHF (mol. wt. 1000 to 3000), 1,4-butanediol, and OCN(CH2)6CN0. In another case Murbach and Adicoff (67) interrupted the regularity of PTHF by copolymerization with ethylene oxide before chain extension with diphenyl-methane-4,4 -disiocyanate. Dickinson (99) prepared a series of polyurethane elastomers from THF-PO copolymer diols and 2,4-tolylene diisocyanate. He found that the use of copolymers with approximately 75 wt.-% THF led to polyurethanes with very good properties relative to the use of propylene oxide homopolymer. 

Furthermore, Wall reviewed the fluorinated polyurethanes prepared from polyesters of fluorinated diols [79], from fluorinated polyethers [80] and detailed their properties [81]. 

THE EFFECT OF SOFT-SEGMENT MOLECULAR WEIGHT UPON THE PROPERTIES OF POLYURETHANES PREPARED FROM POLYCAPROLACTONE MDI 1,4 BUTANE DIOL AT A... 

Polyurethanes, particularly those based on polyesters, are well known for their oil and grease resistance however, they are susceptible to attack by moisture. The structure of the backbone has a profound influence on the hydrolytic stability. The more hydrophobic the backbone, the greater the resistance of the polyurethane towards hydrolysis. Thus, polyether polyurethanes are inherently more stable to hydrolysis than polyester-based materials, and HTPBD-based polyurethanes are even more stable than the polyether materials. Polyurethanes prepared from polycarbonate diols have also been reported to display very good hydrolytic stability. " ... 

Wang Y, et al. Degradation studies on segmented polyurethanes prepared with poly (d, L-lactic acid) diol, hexamethylene diisocyanate and different chain extenders. Polym Degrad Stab 2011 96(9) 1687-94. 

Chan-Chan LH, Vargas-Coronado RF, Cervantes-Uc JM, Cauich-Rodriguez JV, Rath R, Phelps EA, et al. Platelet adhesion and human umbilical vein endothelial cell cytocom-patibility of biodegradable segmented polyurethanes prepared with 4,4 -methylene bis(-cyclohexyl isocyanate), poly(caprolactone) diol and butanediol or dithioerythritol as chain extenders. J Biomater Appl 2013 28(2) 270-7. 

Kinetic studies have been made on the thermal decomposition of a poly(oxypropylene)triol-toluene di-isocyanate copolymer foam. Following a diffusion rate-controlled step, the cellular structure collapses to a viscous liquid and degradation then occurs on a random scission basis. Products of degradation of A-monosubstituted and A A-disubstituted polyurethanes have been analysed by direct pyrolysis in the ion source of a mass spectrometer. The mono-substituted polymers depolymerize quantitatively to di-isocyanates and diols, whereas the disubstituted materials decompose selectively to secondary amines, olefins, and carbon dioxide. The behaviour of the monosubstituted polymers has been confirmed in an i.r. study of the degradation of model compounds. A study of the thermal degradation in vacuum of polyurethanes prepared from butanediol, methylene bis(4-phenylisocyanate), and hexanedioic acid-ethylene glycol-propylene glycol polyesters has been reported and reaction mechanisms proposed. ... 

Polyurethanes can be prepared by treating a diisocyanate with a diol. In preparing polyurethanes, the diols most commonly used are small polymers that bear hydroxyl ends. 

Figure 9. Williams plasticity of polyurethanes prepared from poly-(propylene ether) diols at d erent ratios of 2,4-tolylene diisocyanate...

In this section, mixed-phase polyurethanes prepared from 1,3-butane diol (1,3-BD), HDI, and MDI are reviewed [28]. When the TPU soft and hard segments are phase-mixed, a second element acting as a fixed phase should be introduced. This second element is typically crosslinks intoduced either by an allophanate reaction or by a multifunctional polyol. Shape memory properties, melt viscosities, dynamic mechanical and thermal properties, and stress relaxations in the glassy and rubbery states are discussed. 

Diester/Ether Diol of Tetrabromophthalic Anhydride. This material [77098-07-8] is prepared from TBPA in a two-step reaction. First TBPA reacts with diethylene glycol to produce an acid ester. The acid ester and propylene oxide then react to give a diester. The final product, a triol having two primary and one secondary hydroxyl group, is used exclusively as a flame retardant for rigid polyurethane foam (53,54). 

Acetylene is condensed with carbonyl compounds to give a wide variety of products, some of which are the substrates for the preparation of families of derivatives. The most commercially significant reaction is the condensation of acetylene with formaldehyde. The reaction does not proceed well with base catalysis which works well with other carbonyl compounds and it was discovered by Reppe (33) that acetylene under pressure (304 kPa (3 atm), or above) reacts smoothly with formaldehyde at 100°C in the presence of a copper acetyUde complex catalyst. The reaction can be controlled to give either propargyl alcohol or butynediol (see Acetylene-DERIVED chemicals). 2-Butyne-l,4-diol, its hydroxyethyl ethers, and propargyl alcohol are used as corrosion inhibitors. 2,3-Dibromo-2-butene-l,4-diol is used as a flame retardant in polyurethane and other polymer systems (see Bromine compounds Elame retardants). 

Much more important is the hydrogenation product of butynediol, 1,4-butanediol [110-63-4]. The intermediate 2-butene-l,4-diol is also commercially available but has found few uses. 1,4-Butanediol, however, is used widely in polyurethanes and is of increasing interest for the preparation of thermoplastic polyesters, especially the terephthalate. Butanediol is also used as the starting material for a further series of chemicals including tetrahydrofuran, y-butyrolactone, 2-pyrrohdinone, A/-methylpyrrohdinone, and A/-vinylpyrrohdinone (see Acetylene-DERIVED chemicals). The 1,4-butanediol market essentially represents the only growing demand for acetylene as a feedstock. This demand is reported (34) as growing from 54,000 metric tons of acetylene in 1989 to a projected level of 88,000 metric tons in 1994. 

Step-Growth Gopolymerization. A sample of a block copolymer prepared by condensation polymerisation is shown in equation 30 (37). In this process, a prepolymer diol (HO—Z—OH) is capped with isocyanate end groups and chain extended with a low molecular-weight diol (HO—E—OH) to give a so-called segmented block copolymer, containing polyurethane hard blocks and O—Z—O soft blocks. 

The third approaeh to synthetic polymers is of somewhat less commereial importance. There is in fact no universally accepted deseription for the route but the terms rearrangement polymerisation and polyaddition are commonly used. In many respects this process is intermediate between addition and condensation polymerisations. As with the former teehnique there is no moleeule split out but the kinetics are akin to the latter. A typical example is the preparation of polyurethanes by interaction of diols (di-alcohols, glycols) with di-isocyanates Figure 2.7). 

Fatty acids, both saturated and unsaturated, have found a variety of applications. Brassilic acid (1,11-un-decanedicarboxylic acid [BA]), an important monomer used in many polymer applications, is prepared from erucic acid (Scheme 2), obtained from rapeseed and crambe abyssinica oils by ozonolysis and oxidative cleavage [127]. For example, an oligomer of BA with 1,3-butane diol-lauric acid system is an effective plasticizer for polyvinylchloride. Polyester-based polyurethane elastomers are prepared from BA by condensing with ethylene glycol-propylene glycol. Polyamides based on BA are known to impart moisture resistance. 

A urethane is typically prepared by nucleophilic addition reaction between an alcohol and an isocyanate (R—N = C=0), so a polyurethane is prepared by reaction between a cliol and a diisocyanate. The diol is usually a low-molecular-weight polymer (MW 1000 amu) with hydroxyl end-groups the diisocyanate is often toluene-2,4-diisocyanate. 

Step-growth polymers, the second major class of polymers, are prepared by reactions between difunctional molecules, with the individual bonds in the polymer formed independently of one another. Polycarbonates are formed from a diester and a diol, and polyurethanes are formed from a diisocyanate and a diol. 

Polyurethane (Section 31.4) A step-growth polymer prepared by reaction between a diol and a diisocyanate. 

Polyurethanes (PURs) are usually described as being prepared by the reaction of diols with diisocyanates. However, this is an oversimplification because often water is deliberately added in the production of flexible polyurethane foams. Unreacted isocyanate groups react with water to form carbon dioxide and urea groups in the polymer chain. The carbon dioxide acts as a blowing agent in the production of PUR foams. Also, polyurethanes can be formed by the reaction of bischloroformates with diamines. 

To obtain the polyurethanes, typically a prepolymer was first prepared by reacting the diisocyanate with various diols in dimethylformamide or dimethylacetamide in a two to one molar ratio at 100-110°C for two hours under nitrogen atmosphere. A solution of chain extenders, such as BEP, was then added to the prepolymer reaction mixture and further reacted another three hours. The polymer was isolated by quenching the reaction mixture in cold water. Fine white powder was obtained with a typical yield of around 90%. 

Studies have been made of the elastic (time-independent) properties of single-phase polyurethane elastomers, including those prepared from a diisocyanate, a triol, and a diol, such as dihydroxy-terminated poly (propylene oxide) (1,2), and also from dihydroxy-terminated polymers and a triisocyanate (3,4,5). In this paper, equilibrium stress-strain data for three polyurethane elastomers, carefully prepared and studied some years ago (6), are presented along with their shear moduli. For two of these elastomers, primarily, consideration is given to the contributions to the modulus of elastically active chains and topological interactions between such chains. Toward this end, the concentration of active chains, vc, is calculated from the sol fraction and the initial formulation which consisted of a diisocyanate, a triol, a dihydroxy-terminated polyether, and a small amount of monohydroxy polyether. As all active junctions are trifunctional, their concentration always... 

Polyurethanes (13) have been prepared with optically active diols and various diisocyanates.69 Chiral recognition depends on the diisocyanate... 

---