Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Diffusion residual

A2. Nodal marginal zone lymphoma (MZL). These tumors may show a variable pattern of lymph node infiltration including parafollicular, perisinusal, nodular, and diffuse. Residual reactive follicles may show infiltration by the neoplastic cell population (S30). [Pg.316]

Ionization associated with the presence of solid particles in flames is small and easily obscured by gaseous ionization of volatile impurities. It can be demonstrated experimentally in certain systems and can be shown to depend on the particle size, number density, and work function as predicted by the theory of Smith or Soo and Dimick. Salts such as the alkali halides volatilize slowly and mix by diffusion. Residual inhomogeneities in ion distribution give the appearance of particulate ionization. [Pg.141]

In the earlier versions of the streamline upwinding scheme the modified weight function was only applied to the convection tenns (i.e. first-order derivatives in the hyperbolic equations) while all other terms were weighted in the usual manner. This is called selective or inconsistent upwinding. Selective upwinding can be interpreted as the introduction of an artificial diffusion in addition to the physical diffusion to the weighted residual statement of the differential equation. This improves the stability of the scheme but the accuracy of the solution declines. [Pg.54]

The flow of droplets is directed through a small orifice (Skimmer 1 Figure 12.1) and across a small region that is kept under vacuum by rotary pumps. In this region, approximately 90% of solvent and injected helium is removed from the incipient particle beam. Because the rate of diffusion of a substance is inversely proportional to its molecular mass, the lighter helium and solvent molecules diffuse away from the beam and are pumped away. The heavier solute molecules diffuse more slowly and pass through the first skimmer before they have time to leave the beam the solute is accompanied by residual solvent and helium. [Pg.78]

Transfer occurs by sublimation, condensation, and diffusion (101). Printhead thermal dissipation causes donor dye to travel to the surface of the donor ribbon and convert directiy to a gas. Colorant puffs immediately strike the nearby receptor and soak in, assisted by residual printhead heat. [Pg.51]

An ingenious method to avoid or reduce segregation of alloying elements involves preparing small spheres of material by the atomization of a Hquid stream through a nozzle to produce a powder. This powder can be compacted, often hot and triaxially by gas pressure, to form a material where, on further heating, the residual pores close by diffusion to approach 100% density. [Pg.376]

Film Adhesion. The adhesion of an inorganic thin film to a surface depends on the deformation and fracture modes associated with the failure (4). The strength of the adhesion depends on the mechanical properties of the substrate surface, fracture toughness of the interfacial material, and the appHed stress. Adhesion failure can occur owiag to mechanical stressing, corrosion, or diffusion of interfacial species away from the interface. The failure can be exacerbated by residual stresses in the film, a low fracture toughness of the interfacial material, or the chemical and thermal environment or species in the substrate, such as gases, that can diffuse to the interface. [Pg.529]

The stmcture of residual char particles after devolatilization depends on the nature of the coal and the pyrolysis conditions such as heating rate, peak temperature, soak time at the peak temperature, gaseous environment, and the pressure of the system (72). The oxidation rate of the chat is primarily influenced by the physical and chemical nature of the chat, the rate of diffusion and the nature of the reactant and product gases, and the temperature and pressure of the operating system. The physical and chemical characteristics that influence the rate of oxidation ate chemical stmctural variations, such as the... [Pg.521]

One of the most common rubber adhesives are the contact adhesives. These adhesives are bonded by a diffusion process in which the adhesive is applied to both surfaces to be joined. To achieve optimum diffusion of polymer chains, two requirements are necessary (1) a high wettability of the adhesive by the smooth or rough substrate surfaces (2) adequate viscosity (in general rheological properties) of the adhesive to penetrate into the voids and roughness of the substrate surfaces. Both requirements can be easily achieved in liquid adhesives. Once the adhesive solution is applied on the surface of the substrate, spontaneous or forced evaporation of the solvent or water must be produced to obtain a dry adhesive film. In most cases, the dry-contact adhesive film contains residual solvent (about 5-10 wt%), which usually acts as a plasticizer. The time necessary... [Pg.574]


See other pages where Diffusion residual is mentioned: [Pg.230]    [Pg.336]    [Pg.469]    [Pg.269]    [Pg.230]    [Pg.336]    [Pg.469]    [Pg.269]    [Pg.2767]    [Pg.945]    [Pg.513]    [Pg.68]    [Pg.72]    [Pg.347]    [Pg.144]    [Pg.284]    [Pg.11]    [Pg.212]    [Pg.76]    [Pg.206]    [Pg.456]    [Pg.399]    [Pg.211]    [Pg.266]    [Pg.255]    [Pg.308]    [Pg.227]    [Pg.348]    [Pg.155]    [Pg.521]    [Pg.138]    [Pg.227]    [Pg.245]    [Pg.1441]    [Pg.230]    [Pg.274]    [Pg.195]    [Pg.60]    [Pg.105]    [Pg.208]    [Pg.234]    [Pg.247]    [Pg.457]    [Pg.332]    [Pg.323]    [Pg.333]   
See also in sourсe #XX -- [ Pg.513 , Pg.521 ]




SEARCH



Diffusion systems residues

© 2024 chempedia.info