Corrosion test for engine coolants

D 1384 1987 Method for corrosion test for engine coolants in glassware... [Pg.1099]

D 1384 Test Method for Corrosion Test for Engine Coolants in Glassware... [Pg.143]

An intensive study conducted for the Copper Development Association and reported by Beal [30] reported on two new soldered cup specimens that had been developed to evaluate blooming corrosion effects of solder and soldering parameters using ASTM D 1384 (Corrosion Tests for Engine Coolants in Glassware). Critical examination of the original test revealed wide variations in results in appearance and weight loss so that differences in solder alloy corrosion were difficult to interpret. [Pg.577]

Standard Test Method for Total Immersion Corrosion Test for Soak Tank Metal Cleaners Standard Test Method for Corrosion Test for Engine Coolants in Glassware Standard Test Methods for Rubber O-Rings... [Pg.855]

D 2570 1985 Method for simulated service corrosion testing of engine coolants... [Pg.1099]

D 2570 Test Method for Simulated Service Corrosion Testing of Engine Coolants... [Pg.143]

The salt-water corrosion test is used to evaluate submarine splice closures. For this test a spUce closure tuid its outer housing are immersed in aerated 3.5 % sodium chloride solution for 180 days. The test is described in TA-TSY-041 [17]. The same closures are also exposed to a similar test using artificial fresh water (ASTM D 2570, Method for Simulated Service Corrosion Testing of Engine Coolants). [Pg.767]

Laws have been enacted in many states in an attempt to prevent the sale and distribution of deleterious antifreeze products, such as salt solutions or petroleum coolants. Even ethylene glycol engine coolants must be evaluated by testing and comparison of test results with specifications for engine coolant concentrate, such as ASTM D 3306. These tests ensure desired levels of antifreeze coolant concentrate and inhibitor are available to adequately protect cooling systems against freezing, boilover and corrosion (Fig. 2). [Pg.8]

Select the engine coolant or antirust with care to ensure adequate corrosion protection. Use only those products conforming to recognized standards such as ASTM D 3306 for engine coolant. Additionally, if your vehicle engine contains major cast aluminum components, be certain the engine coolant meets the heat rejection corrosion limits in ASTM specification D 3306 as determined by ASTM Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Transfer Conditions (D 4340). [Pg.10]

D 2809 1989 Test method for cavitation erosion-corrosion characteristics of aluminium pumps with engine coolants... [Pg.1099]

Test method for corrosion of cast aluminium alloys in engine coolants under heat-transfer conditions... [Pg.1100]

Earlier static immersion tests by Noranda on ZA-8 alloy samples in Prestone II engine coolant demonstrated no susceptibility of the alloy to intergranular corrosion. In addition to agitation, differences between the two tests consisted of a higher test temperature and lower glycol/water ratio for the dynamic test. Both factors may have been responsible for the small amount of intergranular corrosion observed. [Pg.82]

Beal, R. E., Testing of Solder for Corrosion by Engine Coolants, Engine Coolant Testing State of the Art, ASTM STP 705, 1980, pp. 327-355. [Pg.579]

Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions Engine Coolant Information Report Engine Coolant Concentrate... [Pg.683]

Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps with Engine Coolants... [Pg.854]

M.S. Vukasovich, F.J. Sullivan, Inhibitors and coolant corrosivity , in RE. Beal (ed). Engine Coolant Testing 2nd Symposium, ASTM STP 887, American Society for Testing and Materials, Philadelphia (1986) pp. 86-98. [Pg.452]

ASTM D4340-96, Standard test method for corrosion of CAST aluminium alloys in engine coolants under heat-rejecting conditions , A STM International (2007) V ol. 15.05. [Pg.453]

Vukasovich, M. S. Sullivan, F. J. (Eds) Inhibitors and Coolant Corrosivity, 2nd International Symposium on Engine Coolants and Their Testing, Philedelphia, American Society for Testing and Materials, 1984. [Pg.160]

Another test described in ASTM D 2809, Test Method for Cavitation Erosion-Corrosion Characteristics of Aluminum Puir ts with Engine Coolants. This test can be used to evaluate automotive water pump materials (aluminum castings) or the abOity of a coolant formulation to prevent metal loss. Chance (Ref... [Pg.90]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...