Copper ductility

Is copper ductile Malleable Brittle Tough Hard or soft ... 

Copper ductile, excellent electrical conductor, valuable metal with many uses... 

Solder Joint Wrought Copper Ductile Iron Pipe... 

Copper is reddish and takes on a bright metallic luster. It is malleable, ductile, and a good conductor of heat and electricity (second only to silver in electrical conductivity). 

Tables 1 and 2, respectively, Hst the properties of manganese and its aHotropic forms. The a- and P-forms are brittle. The ductile y-form is unstable and quickly reverses to the a-form unless it is kept at low temperature. This form when quenched shows tensile strength 500 MPa (72,500 psi), yield strength 250 MPa (34,800 psi), elongation 40%, hardness 35 Rockwell C (see Hardness). The y-phase may be stabilized usiag small amounts of copper and nickel. Additional compilations of properties and phase diagrams are given ia References 1 and 2.

Copper and nickel can be alloyed with zinc to form nickel silvers. Nickel silvers are ductile, easily formed and machined, have good corrosion resistance, can be worked to provide a range of mechanical properties, and have an attractive white color. These alloys are used for ornamental purposes, as sHverplated and uncoated tableware and flatware in the electrical iadustry as contacts, connections, and springs and as many formed and machined parts (see Electrical connectors). 

The bellows is formed from a length of thin-walled tubing by extmsion in a die. The metals used in the constmction of the bellows must be ductile enough for reasonably easy fabrication and have a high resistance to fatigue failure. Materials commonly used are brass, bronze, beryllium copper, alloys of nickel and copper, steel, and Monel (5). 

Molten tin wets and adheres readily to clean iron, steel, copper, and copper-base alloys, and the coating is bright. It provides protection against oxidation of the coated metal and aids in subsequent fabrication because it is ductile and solderable. Tin coatings can be appHed to most metals by electro deposition (see Electroplating). 

Antimony may be added to copper-base alloys such as naval brass. Admiralty Metal, and leaded Muntz metal in amounts of 0.02—0.10% to prevent dezincification. Additions of antimony to ductile iron in an amount of 50 ppm, preferably with some cerium, can make the graphite fliUy nodular to the center of thick castings and when added to gray cast iron in the amount of 0.05%, antimony acts as a powerflil carbide stabilizer with an improvement in both the wear resistance and thermal cycling properties (26) (see Carbides). 

The desked balance of ductility and strength can be obtained in age-hard-enable alloys, such as beryllium copper, by controlling the amount of precipitate. For higher strength, aging is conducted to provide a critical size dispersion. Greater amounts of precipitate are obtained by increasing the beryllium content of the alloy. 

Brasses with up to 15 percent Zn are ductile but difficult to machine. Machinability improves with increasing zinc up to 36 percent Zn. Brasses with less than 20 percent Zn have corrosion resistance eqmvalent to that of copper but with better tensile strengths. Brasses with 20 to 40 percent Zn have lower corrosion resistance and are subject to dezincincation and stress-corrosion cracking, especially when ammonia is present. 

Rubbers are exceptional in behaving reversibly, or almost reversibly, to high strains as we said, almost all materials, when strained by more than about 0.001 (0.1%), do something irreversible and most engineering materials deform plastically to change their shape permanently. If we load a piece of ductile metal (like copper), for example in tension, we get the following relationship between the load and the extension (Fig. 8.4). This can be... 

Fig. 8.4. Load-extension curve tor a bor of ductile metal (e.g. annealed copper) pulled in tension.

Let us first of all look at what happens when we load a cracked piece of a ductile metal - in other words, a metal that can flow readily to give large plastic deformations (like pure copper or mild steel at, or above, room temperature). If we load the material sufficiently, we can get fracture to take place starting from the crack. If you examine the... 

The outstanding properties of copper-base materials are high electrical and thermal conductivity, good durabihty in mildly corrosive chemical environments and excellent ductility for forming complex shapes. As a relatively weak material, copper is often alloyed with zinc (brasses), tin (bronzes), aluminum and nickel to improve its mechanical properties and corrosion resistance. 

Figure 3.5. Eflett of temperature on the tensile strength of copper (A) effect of annealing on strength and ductility (B) hardened high-conductivity copper 129. ...

The strength and ductility of brasses are well maintained over a range of 300° to -180°C, and castings are easy to make as well as to machine. Brass behaves similarly to copper in chemical plant environments, with somewhat greater rates of attack. 

Cast irons are iron with high levels of carbon. Heat treatments and alloying element additions produce gray cast iron, malleable iron, ductile iron, spheroidal cast iron and other grades. The mechanical properties vary significantly. Nickel-containing cast irons have improved hardness and corrosion resistance. Copper or molybdenum additions improve strength. 

---