Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Brass naval

Natural sensitizers Natural tannins Natural vs synthetic dyes Nature ofinvention Nausea N.S. Nautilus Naval brass... [Pg.662]

Naval brass (alloy 465) Naval stores Navane... [Pg.662]

Antimony may be added to copper-base alloys such as naval brass. Admiralty Metal, and leaded Muntz metal in amounts of 0.02—0.10% to prevent dezincification. Additions of antimony to ductile iron in an amount of 50 ppm, preferably with some cerium, can make the graphite fliUy nodular to the center of thick castings and when added to gray cast iron in the amount of 0.05%, antimony acts as a powerflil carbide stabilizer with an improvement in both the wear resistance and thermal cycling properties (26) (see Carbides). [Pg.198]

Phosphorized deoxidized arsenical copper (alloy 142 (23)) is used for heat exchangers and condenser tubes. Copper-arsenical leaded Muntz metal (alloy 366), Admiralty brass (alloy 443), naval brass (alloy 465), and aluminum brass (alloy 687), all find use in condensers, evaporators, ferrules, and heat exchanger and distillation tubes. The composition of these alloys is Hsted in Table 5. [Pg.329]

Admiralty Brass and Naval Brass are 30 and 40% zinc alloys, respectively, to which a 1% tin addition has been added. Resistance to dezincification of Cu—Zn alloys is increased by tin additions. Therefore, these alloys are important for thein corrosion resistance in condenser tube appHcations. In these, as weU as the other higher zinc compositions, it is common to use other alloying additives to enhance corrosion resistance. In particular, a small amount (0.02—0.10 wt %) of arsenic (C443), antimony (C444), or phosphoms (C445) is added to control dezincification. When any of these elements are used, the alloy is referred as being "inhibited." For good stress corrosion resistance, it is recommended that these alloys be used in the fiiUy annealed condition or in the cold worked plus stress reHef annealed condition. [Pg.231]

Cadmium I Mild steel cast iron Low alloy steel 1 Austenitic nickel cast iron 1 Aluminum bronze 1 Naval brass, yellow brass, red brass Tin Copper... [Pg.278]

Copper-alloy tubing, particularly inhibited admiralty, is generally used with cooling water. Copper-alloy tube sheets and baffles are generally of naval brass. [Pg.1073]

Muntz Metal Naval brass Nickel (active)... [Pg.2418]

Admiralty brass Red brass Yellow brass Naval brass Muntz metal... [Pg.360]

Rowlands, J. C., Preferential Phase Corrosion of Naval Brass in Sea-water , 2nd Int. Congr. [Pg.202]

Pb for ease of machining. Duplex (a-/3) brasses containing more than 37% Zn, may have additions of 1% Sn (Naval brass), or 1-3% Pb to assist machining. Both a and a-0 brasses, with and without lead, are used in the cast as well as the wrought form. [Pg.684]

Commercial bronze Red brass Cartridge brass Yellow brass Muntz metal Admiralty brass Admiralty brass Admiralty brass Naval brass Phosphor bronze Phosphor bronze Aluminum bronze Aluminum bronze D... [Pg.46]

Look up the stress-strain diagram for naval brass and determine the CW% where a stress of 400 MPa is applied. Cite the source of your information. [Pg.534]

Naval brass - [CORROSION AND CORROSION CONTROL] (Vol 7) - [COPPERALLOYS-WROUGHTCOPPERANDWROUGHTCOPPERALLOYS] (Vol7) -antimony m [ANTIMONY AND ANTIMONY ALLOYS] (Vol 3) -corrosion of [CORROSION AND CORROSION CONTHOL] (Vol 7)... [Pg.662]

Naval brass (alloy 465) - [ARSENIC AND ARSENIC ALLOYS] (Vol 3)... [Pg.662]

Alloys. Tin is widely used as both a major and minor ingredient of alloy metals. These applications are summarized in Tables 1, 2, and 3. Phosphor bronzes (Table 3) actually contain very little phosphorus, ranging from 0.03 to 0.50%, and hence the alloys are poorly designated. Tin bronzes is the better term. High-silicon bronzes contain about 2.8% tin low-silicon bronzes about 2.0% tin. Gun metals are tin bronze casting alloys with a 5 10% zinc content. Some wrought copper-base alloys contain tin (1) Inhibited Admiralty metal, 1% fin (2) manganese bronze, 1% tin (3) naval brass, 0.75% tin, (4) leaded naval brass, 0.75% tin. See also Copper. [Pg.1617]

Aluminum BronM wW-f Naval Brass, Yellow Brass, Red Brass... [Pg.28]

High brasses and bronzes, naval brass Muntz metal -0.30 0.45 ... [Pg.65]

Naval brass, yellow brass, red brass Aluminum bronze [... [Pg.350]

Leaded Brass, Naval Brass, Leaded Bronze... [Pg.31]

See other pages where Brass naval is mentioned: [Pg.105]    [Pg.231]    [Pg.280]    [Pg.2458]    [Pg.315]    [Pg.82]    [Pg.19]    [Pg.23]    [Pg.1270]    [Pg.369]    [Pg.683]    [Pg.684]    [Pg.696]    [Pg.698]    [Pg.242]    [Pg.614]    [Pg.206]    [Pg.27]    [Pg.205]    [Pg.205]    [Pg.225]    [Pg.82]    [Pg.118]    [Pg.627]    [Pg.622]    [Pg.105]    [Pg.209]    [Pg.236]    [Pg.132]   
See also in sourсe #XX -- [ Pg.4 , Pg.54 ]

See also in sourсe #XX -- [ Pg.4 , Pg.54 ]

See also in sourсe #XX -- [ Pg.185 ]



SEARCH



Brass

Naval

© 2024 chempedia.info