Copper: characteristics

Performance can be illustrated for example by the time necessary for deaeration or de-emulsification of oils, anti-rust properties, copper strip corrosion test, the flash point in closed or open cup, the cloud and pour points, the foaming characteristics, etc. 

A characteristic property of an aldehyde function is its sensitivity to oxidation A solu tion of copper(II) sulfate as its citrate complex (Benedict s reagent) is capable of oxi dizing aliphatic aldehydes to the corresponding carboxylic acid... 

The sensitivity of an atomic absorption line is often described by its characteristic concentration, which is the concentration of analyte giving an absorbance of 0.00436 (corresponding to a percent transmittance of 99%). Eor example. Table 10.11 shows a list of wavelengths and characteristic concentrations for copper. 

Printed circuit boards manufacture is aided by the use of KMnO. Alkaline permanganate solution is used to remove resin smeared on the interior hole wall of multilayered printed circuit boards. Additionally the hole wall is etched, resulting in a surface with excellent adhesion characteristics, for electrodeless copper (250). The alkaline permanganate etchback system containing >60 g/L KMnO and 40-80 g/L NaOH at 70—80°C, is effective for difunctional, tetrafiinctional, and polyimide resin substrates, where the level of etchback is direcdy proportional to the immersion time (10—20 min) (251). 

Copper Development Association P.O. Box 1840 Greenwich, Conn. 06836 Standards for wrought and cast copper and copper alloy products a standards handbook is pubUshed with tolerances, alloy data, terminology, engineering data, processing characteristics, sources and specifications cross-indexes for six coppers and 87 copper-based alloys that are recognized as standards. 

In electrogalvanizing, copper foil, and other oxygen-evolving appHcations, the greatest environmental contribution has been the elimination of lead-contaminated waste streams through replacement of the lead anode. In addition, the dimensionally stable characteristic of the metal anode iatroduces greater consistency and simplification of the process, thus creating a measure of predictabiUty, and a resultant iacreased level of safety. 

The characteristics of a powder that determine its apparent density are rather complex, but some general statements with respect to powder variables and their effect on the density of the loose powder can be made. (/) The smaller the particles, the greater the specific surface area of the powder. This increases the friction between the particles and lowers the apparent density but enhances the rate of sintering. (2) Powders having very irregular-shaped particles are usually characterized by a lower apparent density than more regular or spherical ones. This is shown in Table 4 for three different types of copper powders having identical particle size distribution but different particle shape. These data illustrate the decisive influence of particle shape on apparent density. (J) In any mixture of coarse and fine powder particles, an optimum mixture results in maximum apparent density. This optimum mixture is reached when the fine particles fill the voids between the coarse particles. 

A third group includes silver—nickel, silver—cadmium oxide, and silver—graphite combinations. These materials are characterized by low contact resistance, some resistance to arc erosion, and excellent non sticking characteristics. They can be considered intermediate in overall properties between silver alloys and silver or copper—refractory compositions. Silver—cadmium oxide compositions, the most popular of this class, have wide appHcation in aircraft relays, motor controllers, and line starters and controls. 

The treatments used to recover nickel from its sulfide and lateritic ores differ considerably because of the differing physical characteristics of the two ore types. The sulfide ores, in which the nickel, iron, and copper occur in a physical mixture as distinct minerals, are amenable to initial concentration by mechanical methods, eg, flotation (qv) and magnetic separation (see SEPARATION,MAGNETIC). The lateritic ores are not susceptible to these physical processes of beneficiation, and chemical means must be used to extract the nickel. The nickel concentration processes that have been developed are not as effective for the lateritic ores as for the sulfide ores (see also Metallurgy, extractive Minerals recovery and processing). 

For many electronic and electrical appHcations, electrically conductive resias are required. Most polymeric resias exhibit high levels of electrical resistivity. Conductivity can be improved, however, by the judicious use of fillers eg, in epoxy, silver (in either flake or powdered form) is used as a filler. Sometimes other fillers such as copper are also used, but result in reduced efficiency. The popularity of silver is due to the absence of the oxide layer formation, which imparts electrical insulating characteristics. Consequently, metallic fibers such as aluminum are rarely considered for this appHcation. 

AEROPHINE 3418A promoter is widely used ia North and South America, AustraHa, Europe, and Asia for the recovery of copper, lead, and ziac sulfide minerals (see Elotatton). Advantages ia comparison to other collectors (15) are said to be improved selectivity and recoveries ia the treatment of complex ores, higher recoveries of associated precious metals, and a stable grade—recovery relationship which is particularly important to the efficient operation of automated circuits. Additionally, AEROPHINE 3418A is stable and, unlike xanthates (qv), does not form hazardous decomposition products such as carbon disulfide. It is also available blended with other collectors to enhance performance characteristics. 

Glass-lined reactor systems ate used occasionally for halogenated resins to prevent corrosion of the reactor components. Copper and brass fitting should be avoided due to the significant induence on resin cute characteristics. 

Toluhydroquinone and methyl / fX butyUiydroquinone provide improved resin color retention 2,5-di-/-butyIhydroquinone also moderates the cure rate of the resin. Quaternary ammonium compounds, such as benzyl trimethyl ammonium hydroxide, are effective stabilizers in combination with hydroquinones and also produce beneficial improvements in color when promoted with cobalt octoate. Copper naphthenate is an active stabilizer at levels of 10 ppm at higher levels (150 ppm) it infiuences the cure rate. Tertiary butylcatechol (TBC) is a popular stabilizer used by fabricators to adjust room temperature gelation characteristics. 

Copper naphthenate added to the resin at levels between 100—200 ppm effectively extends gel and cure characteristics, resulting in a reduction in exothermic heat (Eig. 7). Copper additives are used widely in commercial laminating resins to modify process exothermic effects. a-Methylstyrene [98-83-9] substituted for styrene at levels of 5—8% has also been used effectively in resins cured at above ambient temperatures. The inhibitor 2,5-di-/-butyIhydroquinone exerts significant exotherm suppression at levels of 200—400 ppm and is useful in high temperature mol ding processes. 

Alloying elements such as nickel, chromium, molybdenum, and copper, which may be introduced with scrap, can increase the hardenability, although only slightly, because the concentrations are ordinarily low. However, the heat-treating characteristics may change, and for appHcations in which ductihty is important, as in low carbon steels for deep drawing, the increased hardness and lower ductiHty imparted by these elements may be harmful. 

---