Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Controller distributed control systems

NOTE Instrumented systems in the process sector are typically composed of sensors (for example, pressure, flow, temperature transmitters), logic solvers or control systems (for example, programmable controllers, distributed control systems), and final elements (for example, control valves). In special cases, instrumented systems can be safety instrumented systems (see 3.2.72). [Pg.30]

The basic characteristics of alarm systems have already been covered at length in Chapter IX. Since an alarm is one of the most fundamental issues in a control system, it will be discussed here again in this context. In this clause, focus will be on independent alarm systems that can be applied to critical applications independently of a programmable logic controller/distributed control system (PLC/DCS). In spite of so much technological developments and modem instrumentation and... [Pg.710]

The functionality of the PLC has evolved over the years to include sequential relay control, motion control, process control, distributed control systems, and networking. The data handling, storage, processing power, and communication capabilities of some modem PLCs are approximately equivalent to desktop computers. A major advantage of PLCs is that it is typically armored for severe conditions, such as dust, moisture, heat, cold. Also, PLCs have the facility for extensive input/output (I/O) arrangements for connecting the PLC to sensors and actuators. [Pg.302]

A central location where instmment leads are short is preferred. In modem faciHties with distributed control systems, all units are controUed from a central control room with few operators. Only a few roving operators are available to spot trouble. It is desirable to deep process equipment a minimum of 8 m away from the control room. Any equipment and hydrocarbon-containing equipment should be separated by at least 15 m if possible. Most control rooms are designed with blastproof constmction and have emergency backup power and air conditioning. The room is pressuri2ed to prevent infusion of outside air that may have hydrocarbon content in the explosive range. [Pg.79]

Fig. 2. Distributed control system stmcture, where PIU = process interface unit LCUj = local control unit, model 1 LCU2 = local control unit, model 2 ... Fig. 2. Distributed control system stmcture, where PIU = process interface unit LCUj = local control unit, model 1 LCU2 = local control unit, model 2 ...
Fermentation. The term fermentation arose from the misconception that black tea production is a microbial process (73). The conversion of green leaf to black tea was recognized as an oxidative process initiated by tea—enzyme catalysis circa 1901 (74). The process, which starts at the onset of maceration, is allowed to continue under ambient conditions. Leaf temperature is maintained at less than 25—30°C as lower (15—25°C) temperatures improve flavor (75). Temperature control and air diffusion are faciUtated by distributing macerated leaf in layers 5—8 cm deep on the factory floor, but more often on racked trays in a fermentation room maintained at a high rh and at the lowest feasible temperature. Depending on the nature of the leaf, the maceration techniques, the ambient temperature, and the style of tea desired, the fermentation time can vary from 45 min to 3 h. More highly controlled systems depend on the timed conveyance of macerated leaf on mesh belts for forced-air circulation. If the system is enclosed, humidity and temperature control are improved (76). [Pg.372]

Microprocessor technology permitted these technical issues to be addressed in a cost-effec tive manner. In the mid-1970s, a process control architecture referred to as a distributed control system (DCS) was introduced and almost instantly became a commercial success. A DCS consists of some number of microprocessor-based nodes that are interconnec ted by a digital communications network, often called a data highway. The key features of this architecture are as follows ... [Pg.771]

Figure 8-62 depicts a hypothetical distributed control system. A number of different unit configurations are illustrated. This system consists of many commonly used DCS components, including multiplexers (MUXs), single/multiple-loop controllers, programmable logic controllers (PLCs), and smart devices. A typical system includes the following elements as well ... [Pg.771]

The component controllers used in the controller subsystem portion of the DCS can be of various types and include multiloop controllers, programmable logic controllers, personal computer controllers, singleloop controllers, and fieldbus controllers. The type of elec tronic con-troUer utihzed depends on the size and func tional characteristic of the process apphcation being controlled. See the earlier section on distributed control systems. [Pg.775]

Digital Field Communications An increasing number of valve-mounted devices are available that support digital communications in addition to, or in place of, the traditional 4—20 mA current signal. These control-valve devices have increased functionality, resulting in reduced setup time, improved control, combined functionality of traditionally separate devices, and control-valve diagnostic capabihty. Digital communications also allow the control system to become completely distributed where, for example, the process PID controller could reside in the valve positioner or in the process transmitter. [Pg.786]

Distributed Control System (DCS) A system that divides process control functions into specific areas interconnected by communications (normally data highways) to form a single entity. It is characterized by digital controllers, typically administered by central operation interfaces and intermittent scanning of the data highway. [Pg.160]

Minimization of pollutants from the combustion chamber. This approach consists of designing the engine with improved fuel-air distribution systems, ignition timing, fuel-air ratios, coolant and mixture temperatures, and engine speeds for minimum emissions. The majority of automobiles sold in the United States now use an electronic sensor/control system to adjust these variables for maximum engine performance with minimum pollutant emissions. [Pg.525]

Engineering factors include (a) contaminant characteristics such as physical and chemical properties - concentration, particulate shape, size distribution, chemical reactivity, corrosivity, abrasiveness, and toxicity (b) gas stream characteristics such as volume flow rate, dust loading, temperature, pressure, humidity, composition, viscosity, density, reactivity, combustibility, corrosivity, and toxicity and (c) design and performance characteristics of the control system such as pressure drop, reliability, dependability, compliance with utility and maintenance requirements, and temperature limitations, as well as size, weight, and fractional efficiency curves for particulates and mass transfer or contaminant destruction capability for gases or vapors. [Pg.22]

The elements of a PM plan include periodic inspection, cleaning, and service as warranted, adjustment and calibration of control system components, maintenance equipment and replacement parts that are of good quality and properly selected for the intended function. Critical HVAC system components that require PM in order to maintain comfort and deliver adequate ventilation air include a outdoor air intake opening, damper controls, air filters, drip pans, cooling and heating coils, fan belts, humidification equipment and controls, distribution systems, exhaust fans. [Pg.211]

A distributed control system (DCS) normally uses input and output modules which contain eight, sixteen, or more inputs or outputs. Failure of the module will simultaneously disable a large number of control loops. Attention to the assignment of input/output points to the modules makes the plant more tolerant of a failure of an input or output module (CCPS, 1993a). For a more detailed discussion of process control systems, see the process control part of Section 4.4, and Sections 6.4 and 6.5. [Pg.51]

In one site, the project team installing a DCS (Distributed Control System) carefully developed and tested techniques to make the displays clear for red-green color blind personnel (see discussion in 6.4). The displays were effective and were applauded by the operators. However, in subsequent DCS installation projects at the same site, different project teams made no provision to make displays visible to red-green color blind personnel. This inherently less safe condition was found during a design review at one unit and at the pre-start-up safety review for another unit. [Pg.112]

Rousseau, R.W. and Howell, T.R., 1982. Comparison of simulated crystal size distribution control systems based on nuclei density and super-saturation. Industrial and Engineering Chemistry Process Design and Development, 21, 606. [Pg.321]

Unfortunately the address of the gateway in the control computer used for the data transfer was the same as that used to connect to the distributed control system (dcs). As a result data flowed from the simulator through the control computer to the dcs and replaced the current input data by historic data. Some conditions on the plant started to change, but fortunately this was soon noticed by alert operators, and the plant was brought back under control. [Pg.362]

An air conditioning system uses an assembly of equipment to treat air. Normally the assembly includes a heating system for modifying winter indoor temperature and humidity a refrigeration system for modifying summer temperature and humidity, a means to maintain indoor air quality (i.e., air filters and fresh air intake) a method of distribution of conditioned air and a control system, such as a thermostat, to maintain desired comfort conditions. [Pg.22]

Improved boiler design/operation (cogeneration), and distributed control systems... [Pg.755]

This chapter presents the entire procedure for performing heat and weight balances. The last section of the chapter discusses the use of the distributed control system and computer in automating the process... [Pg.140]

If the unit does not have a distributed control system (DCS), a debottlenecking project is the right time to justify it. If it does have a DCS, advanced control projects should be justified. A DCS ... [Pg.305]


See other pages where Controller distributed control systems is mentioned: [Pg.497]    [Pg.497]    [Pg.497]    [Pg.145]    [Pg.195]    [Pg.337]    [Pg.398]    [Pg.107]    [Pg.417]    [Pg.42]    [Pg.352]    [Pg.23]    [Pg.61]    [Pg.64]    [Pg.67]    [Pg.497]    [Pg.716]    [Pg.718]    [Pg.739]    [Pg.755]    [Pg.771]    [Pg.775]    [Pg.2509]    [Pg.149]    [Pg.165]    [Pg.179]    [Pg.183]    [Pg.231]    [Pg.436]    [Pg.452]    [Pg.634]    [Pg.46]    [Pg.51]    [Pg.254]   


SEARCH



Computer-directed distributed control systems

Controlled distribution

Corrosion Control in Water Distribution Systems

Crystallizers distributed control systems

Design of distributed computer control systems

Design strategies distributed control systems

Digital technology distributed control system

Distributed Control System management

Distributed computer control, hierarchical systems

Distributed control system approach

Distributed control system areas

Distributed control system background

Distributed control system programmable logic controllers

Distributed control system structure

Distributed control systems Distributions

Distributed control systems Distributions

Distributed control systems gamma

Distributed control systems normal

Distributed control systems standard normal

Distributed controls systems

Distributed controls systems

Distribution system

Distributive control system

Instruments distributed control system

Process monitoring distributed control system

Velocity distributions, pressure-control systems

© 2024 chempedia.info