Chromium characteristics

Standard Wrought Steels. Steels containing 11% and more of chromium are classed as stainless steels. The prime characteristics are corrosion and oxidation resistance, which increase as the chromium content is increased. Three groups of wrought stainless steels, series 200, 300, and 400, have composition limits that have been standardized by the American Iron and Steel Institute (AlSl) (see Steel). Figure 8 compares the creep—mpture strengths of the standard austenitic stainless steels that are most commonly used at elevated temperatures (35). Compositions of these steels are Hsted in Table 3. 

Many types of stainless steels are available. The type most widely used in the dairy industry is 18—8 (18% chromium, 8% nickel plus iron). Small amounts of siHcon, molybdenum, manganese, carbon, sulfur, and phosphoms maybe included to obtain characteristics desired for specific appHcations. 

Chromium(III) Chemistry. The most characteristic reactions of Cr(III) in aqueous solution at >4 pH, eg, in the intestine and blood, and hydrolysis and olation (147). As a consequence, inorganic polymeric molecules form that probably are not able to diffuse through membranes. This may be prevented by ligands capable of competing for coordination sites on Cr(III) (see Coordination compounds) (147). Thus any large fraction of ingested Cr(III) should be absorbed. Chromium (ITT) in the form of GTF may be more efficiendy absorbed. 

Alloying elements such as nickel, chromium, molybdenum, and copper, which may be introduced with scrap, can increase the hardenability, although only slightly, because the concentrations are ordinarily low. However, the heat-treating characteristics may change, and for appHcations in which ductihty is important, as in low carbon steels for deep drawing, the increased hardness and lower ductiHty imparted by these elements may be harmful. 

Although a minimum content of 12wt% Cr is required to impart the stainless characteristic to steels, much effort has been appHed to develop new grades of stainless steel having significantly reduced chromium contents without unacceptable degradation of corrosion resistance and other properties. There has been some modest success in this endeavor (34,53—56). 

Acid—mordant dyes have characteristics similar to those of acid dyes which have a relatively low molecular weight, anionic substituents, and an affinity to polyamide fibers and mordant dyes. In general, brilliant shades caimot be obtained by acid—mordant dyes because they are used as their chromium mordant by treatment with dichromate in the course of the dyeing procedure. However, because of their excellent fastness for light and wet treatment, they are predominandy used to dye wool in heavy shades (navy blue, brown, and black). In terms of chemical constitution, most of the acid—mordant dyes are azo dyes some are triphenyhnethane dyes and very few anthraquinone dyes are used in this area. Cl Mordant Black 13 [1324-21 -6] (183) (Cl 63615) is one of the few examples of currentiy produced anthraquinone acid—mordant dyes. It is prepared by condensation of purpurin with aniline in the presence of boric acid, followed by sulfonation and finally by conversion to the sodium salt (146,147). 

The engineering properties of electroless nickel have been summarhed (28). The Ni—P aHoy has good corrosion resistance, lubricity, and especiaHy high hardness. This aHoy can be heat-treated to a hardness equivalent to electrolytic hard chromium [7440-47-3] (Table 2), and the lubricity is also comparable. The wear characteristics ate extremely good, especiaHy with composites of electroless nickel and silicon carbide or fluorochloropolymers. Thus the main appHcations for electroless nickel are in replacement of hard chromium (29,30). 

Concentration Effects. The reactivity of ethyl alcohol—water mixtures has been correlated with three distinct alcohol concentration ranges (35,36). For example, the chromium trioxide oxidation of ethyl alcohol (37), the catalytic decomposition of hydrogen peroxide (38), and the sensitivities of coUoidal particles to coagulation (39) are characteristic for ethyl alcohol concentrations of 25—30%, 40—60%, and above 60% alcohol, respectively. The effect of various catalysts also differs for different alcohol concentrations (35). 

L3M45M4 5 would often appear as L3M2,3V and L3W, respectively, and similarly 1 2,3 4,5 4,51 as M2,3W. In Fig. 2.22 the increase in the intensity of the L3W peak relative to the other two, upon going from chromium to iron, is because of the progressive increase in the electron density in the valence band. The characteristic doublet seen in the MNN series arises from the M4 5N4,sN4,5 transitions, in which the doublet separation is that of the core levels M4 and M5. 

This characteristic of RAIR can be observed experimentally. Fig. 8 shows the transmission spectrum of polydimethylsiloxane (PDMS) while Fig. 9 shows the RAIR spectrum of a thin film of PDMS spin-coated onto a chromium substrate. It can be observed that the bands near 1024 and 1095 cm have similar intensities in the transmission spectra but the band at higher frequencies is clearly much more intense in the RAIR spectrum. This change in relative intensity when PDMS is deposited onto a reflecting substrate is related to optical effects and is not related to orientation effects. 

Chromium diffusion applied to a low-carbon steel produces a surface that has the characteristics of ferritic stainless steel, such as AISI446 to a depth about 0.1 mm. When diffusion is applied to a high-carbon steel, a surface rich in chromium carbides is formed. This has a hardness greater than 1000 VHN, which provides good resistance to abrasion. 

Cephachlor (35) became accessible when methods for the preparation of C-3 methylenecephalosporins became convenient. The allylic C-3-acetoxyl residue characteristic of the natural cephalosporins is activated toward displacement by a number of oxygen- and sulfur-containing nucleophiles. Molecules such as can therefore be prepared readily. Subsequent reduction with chromium(II) salts leads to the desired C-3... 

The main characteristic of attack by halogens at elevated temperatures is that most reaction products are volatile compared with the solid products that form in all cases considered hitherto in this chapter. Thus, in cases where metals are exposed to pure halogen gases large mass losses are usually reported with very little external scale formation. Li and Rapp " showed that internal chloridation occurred when nickel-chromium alloys were exposed to Ni + NiClj powders at 700-900°C. However, where oxide scales can also form, as in combustion gases, the oxide layer was usually highly... 

Other ions which are reduced in the reductor to a definite lower oxidation state are those of titanium to Ti3+, chromium to Cr2+, molybdenum to Mo3+, niobium to Nb3+, and vanadium to V2 +. Uranium is reduced to a mixture of U3 + and U4+, but by bubbling a stream of air through the solution in the filter flask for a few minutes, the dirty dark-green colour changes to the bright apple-green colour characteristic of pure uranium(I V) salts. Tungsten is reduced, but not to any definite lower oxidation state. 

---