Chromatography HPLC injection

High performance liquid chromatography (HPLC) is an excellent technique for sample preseparation prior to GC injection since the separation efficiency is high, analysis time is short, and method development is easy. An LC-GC system could be fully automated and the selectivity characteristics of both the mobile and stationary... 

Heat and reflux a 5-g portion of soil sample with 50 mL of methanol-phosphate buffer (pH 7)-water (15 7 28, v/v/v) solvent mixture in a round-bottom flask for 1 h. After cooling, transfer a 10-mL portion of the supernatant to a test-tube and mix with 11 mL of 0.02M H3PO4 solution. Load this solution on to a silica-based SPE cartridge (Analytichem International Clin-Elut 1020) at a flow rate of 1-2 drops per second. Discard this fraction. Elute the analytes with 30 mL of dichloromethane. Concentrate the eluate to dryness with air in a water-bath at a temperature of 40 °C (do not use vacuum). Dissolve the residues in 5mL of HPLC injection solution [900 mL of water - - 50 mL of phosphate buffer (pH 7) 4-50 mL of ACN 4-4 g of TBABr]. Pinal analysis is performed using liquid chromatography/ultraviolet detection (LC/UV) with a three-column switching system. 

Milbemectin consists of two active ingredients, M.A3 and M.A4. Milbemectin is extracted from plant materials and soils with methanol-water (7 3, v/v). After centrifugation, the extracts obtained are diluted to volume with the extraction solvent in a volumetric flask. Aliquots of the extracts are transferred on to a previously conditioned Cl8 solid-phase extraction (SPE) column. Milbemectin is eluted with methanol after washing the column with aqueous methanol. The eluate is evaporated to dryness and the residual milbemectin is converted to fluorescent anhydride derivatives after treatment with trifluoroacetic anhydride in 0.5 M triethylamine in benzene solution. The anhydride derivatives of M.A3 and M.A4 possess fluorescent sensitivity. The derivatized samples are dissolved in methanol and injected into a high-performance liquid chromatography (HPLC) system equipped with a fluorescence detector for quantitative determination. 

Most of the reported methods of analysis of valproic acid and its sodium salt in biological fluids rely on the use of chromatography, especially gas chromatography, although high performance liquid chromatography (HPLC) is also reported. Other methods, such as flow injection analysis, enzyme-immunoassay, fluorescence-polarization capillary electrophoresis, and potentiometry are sometimes used. The reported methods can be classified as follows. 

Procedure Flavonoids are then further purified with 2 ml of methanolic HC1 (2 N), followed by centrifugation (2 min, 15 600 g), hydrolyzation of 150 il of suspension in an autoclave (15 min, 120 C). A reverse osmosis-Millipore UF Plus water purification system is used in high performance liquid chromatography (HPLC) with an autosampler. After injections of 5 pg of samples, the mobile phases flow at a rate of 1 ml/minute with isocratic elution in a column at 30 C. 

Figure 7.5 Schematic diagram of a high performance liquid chromatography (HPLC) system. The solvent(s) are pumped through the system, and the sample injected just before the column where separation occurs. Detection is often by UV/visible spectrophotometry at a fixed wavelength.

High Performance Liquid Chromatography (HPLC) (Chapter 30) gives an elaborate discussion of theoretical aspects. Instrumentation encompasses the various important components e.g., solvent reservoir and degassing system pressure, flow and temperature pumps and sample injection system ... 

The precipitate was then analyzed using high performance liqnid chromatography (HPLC) to reaffirm the results as characterized by the IR analysis. The precipitate was collected and dissolved in an acetone solntion with water (1 2 v/v) acting as the solvent before the analysis was done. Finally, the 1.0 ppm concentrated sample was injected into a HPLC machine. The chromatogram shows a peak at the retention time (Rj) which is almost the same as the retention time of standard vanillin with the same concentration. Figure 9.4 presents the HPLC chromatograms of the vanillin sample and the standard vanillin. 

In the separation of biomolecules, sample preparation almost always involves the use of one or more pretreatment techniques. With high-performance liquid chromatography (HPLC), no one sample preparation technique can be appHed to all biological samples. Several techiques may be used to prepare the sample for injection. For example, complex samples require some form of preffactionation before analysis, samples that are too dilute for detection require concentration before analysis, samples in an inappropriate or incompatible solvent require buffer exchange before analysis, and samples that contain particulates require filtration before injection into the analytical instrument. 

High pressure liquid chromatography (HPLC) was used for the quantitative measurement of quinones and hydroquinones in the cultures. 20 pi of supernatant were injected in a Merck-Hitachi HPLC system 655A-12 equipped with a 4.6 x 250 mm Nucleosil C18 column (5 pm, RP 18). The system was run at a flow rate of 1 ml min-1 with a methanol/water gradient (10 to 20% methanol in 15 min, then 20 to 100% methanol in 5 min). The UV detector was operated at 281 nm or 275 nm to follow the reduction of quinones 13 and 14, respectively (37). 

Electrochemical detection under convective conditions has been applied widely in freshwater measurements. In addition, seawater measurements have been combined with flow injection analysis (FIA) and high pressure liquid chromatography (HPLC) (D.C. Johnson et al., 1986). Well-developed commercial product lines exist, and detection limits are typically in the range of femtomoles. For in situ, shipboard, and land-based measure-... 

---