Chemicals instruction documentation

For any chemical whose identity is claimed as a trade secret, you must submit to EPA two versions of the substantiation form as prescribed in 40 CFR Part 350, published July 29, 1988 In the Federal Register (53 FR 28772). Use the order form In this document to obtain a copy of the rule and substantiation form. One version identifies the chemical the second version does not Identify the chemical specifically, but provides instead a generic identity. Only this latter version will be available to the public. For further explanation of the trade-secret provisions, see the instructions below... 

The submissions of section 313 reports in magnetic media and computer-generated facsimile formats has been approved by EPA. Magnetic media submissions to EPA must follow basic specifications set forth by EPA in the document. Magnetic Media Submissions Instructions fEPA 560/4-90-008) which is also included in EPA s Toxic Chemical Release Inventory Reporting Package for 1989 (EPA 560/4-90-001). To order these documents, see the document request form in Appendix I. 

What chemicals was the Army studying Why was the program never fully documented in books available to the public Who planned and carried out the tests, and what was their purpose How, and by whom, were the volunteers recruited How adequately were they instructed before giving their informed consent What long range effects, if any, have been found in follow-up studies ... 

It helps them to reduce systematically their use of hazardous chemicals and develop new products. Some companies have agreed on substances that need to be avoided. As documented In the case studies In Annex I of this report, they are Instructing their suppliers to phase out a range of carcinogenic, mutagenic and reproductive toxins, as well as some persistent, bloaccumulative, and endocrine disrupting chemicals. 

Documents describing the equipment and procedures should be available to the operators and technicians responsible for the sampling and chemical analysis, and these documented procedures should be followed to the letter. All the personnel involved should be adequately trained and instructed. 

Laboratories worldwide have different facilities, instrumentation, personnel, and perhaps differing procedures, which means that each laboratory actually requires its own work instructions. These work instructions have to be included in the quality system documentation of the laboratory. In constructing work instructions, the ROPs can offer consultancy (7). In addition, there are other useful literature available discussing the methods for analysis of CWC-related chemicals and giving examples on how the laboratories have performed in round-robin tests or PTs (8 l4). 

The EU Commission Decision EC 2002/657 prescribes the use of RMs or CRMs [4]. Eurachem has published a document that provides instructions to analytical chemists on the selection and use of RMs [31]. Different types of RMs exist, namely, pure substances, standard solutions, matrix RMs, physical-chemical RMs, and reference objects or artifacts. The difference between RMs and CRMs lies in that the values or properties of a CRM are certified during a collaborative trial according to a well-defined protocol, whereas the values or properties of an RM are defined, but have not been established through a collaborative trial. The following classes are generally used for RMs primary, secondary, and in-house or working RMs. The uncertainty associated with primary RMs is the smallest, while in-house RMs have the largest uncertainty. 

In countries dealing with destruction of chemical warfare agents, control limits for exposure via surface contact of drinking water are needed, as are detection methods for their low levels in water, soil, or foodstuffs. Some of the toxicity parameters of RVX for humans and animals are available in the text A Book of Instructions and Technical Documentation on the Problem of Chemical Weapon Destruction (Anon, 2001), and are given in Table 7.6. 

Instruction for the Calculation of the Chemical Hazard Potential, Nuclear Decommissioning Authority, 13 June 2006, Document No. EGPR02, Revision 1. 

Chemicals, reagents, and solutions should be labeled to indicate identity (with concentration if appropriate), expiry date and specific storage instructions. Information concerning source, preparation date and stability should be available. The expiry date may be extended on the basis of documented evaluation or analysis. 

I have provided your supervisors with copies of a document on MSDSs that should be very helpful as you proceed in this work. It is a section entitled Exploring MSDSs found in the book Building Student Safety Habits for the Workplace, published by Terrific Science Press at the Center for Chemical Education at Miami University, Middletown, OH. This section includes a set of instructions for doing exactly what is required for this project (Exercise 3B). I also have made photocopies of the labels in question (found in Section 2B in the above referenced book) and the MSDSs (found in Section 3B in the above referenced book). Also, your supervisors will decide who should evaluate which labels. I have recommended that each participant be assigned two of the four chemicals (four labels) at random, meaning that each participant will each have four labels to evaluate, a consumer product label and an industrial chemical product label for one chemical and a consumer product label and industrial chemical product label for a second chemical. Please use the method suggested for Exercise 3B in the book referenced above and keep a good record of your work in your notebook so that you can prepare a quality report memo for WSHA. 

During a search of Record Group 70, Bureau of Mines, the District of Columbia found a document entitled, Instructions for the Care, Storage and Handling of Gas Warfare Material. This manual was issued by the Gas Service A.E.F. on June 15, 1918. The manual states, If a leak is suspected it should be reported immediately and all men required to work near the dump should keep the respirator in the alert position. The suspected shell should be immediately located and removed and buried. .. Holes 4 feet deep will always be kept prepared. .. Piles of earth and a spade should be kept near the chemical projectile stacks, to cover up the liquid that has escaped. 

Are there procedures or instructions in place to specify when review and approval are needed on project documentation to ensure that any chemical hazards management concerns are addressed ... 

The reliability of electronic systems depends on extensive testing, inspection, and evaluation of all parts of the design and manufacturing process, including the adhesives used in the systems. Test methods for adhesives and adhesive-bonded assemblies may be generally classified as physical, electrical, environmental, thermal, mechanical or thermomechanical, and chemical (Table 7.1). This chapter summarizes most of the methods used to test and evaluate adhesives used in electronics. It is not intended to provide detailed instructions, but to lead the reader to the appropriate government or industry specifications, documents that are available from the various organizations listed in Table 7.2. 

A list of substances that were subject to TSCA actions at the time of the 2006 Inventory was contained in Appendix C to the Instructions for Reporting for the 2006 Partial Updating of the TSCA Chemical Inventory Database. (Nov. 2006) [hereinafter 2006 Instructions]. However. EPA makes clear in that Appendix that the Appendix is intended to be only an information resource. The list should not be relied upon in lieu of relevant orders. Federal Register documents, or the Code of Federal Regulations. 

---