Carbon tetrachloride, reactions

Chlorine reacts with saturated hydrocarbons either by substitution or by addition to form chlorinated hydrocarbons and HCl. Thus methanol or methane is chlorinated to produce CH Cl, which can be further chlorinated to form methylene chloride, chloroform, and carbon tetrachloride. Reaction of CI2 with unsaturated hydrocarbons results in the destmction of the double or triple bond. This is a very important reaction during the production of ethylene dichloride, which is an intermediate in the manufacture of vinyl chloride ... 

The submitters have prepared the following thiocarbamyl chlorides by the chlorination of the corresponding disulfides dimethylthiocarbamyl chloride, b.p. 90-95°/0.5 mm., m.p. 42.5-43.5°, carbon tetrachloride reaction medium diisopropylthio-carbamyl chloride, m.p. 69-71°, benzene reaction medium diiso-butylthiocarbamyl chloride, m.p. 46-48°, no solvent. 

Much of the early work with ruthenium tetroxide also made use of stoichiometric amounts of a solution of the reagent in an inert solvent, such as carbon tetrachloride. Reactions were carried out at room temperature. The general acceptance of the reagent as a powerful wide-ranging oxidant, coupled with the expense of ruthenium me, however, later provided the incentive to develop alternative catalytic... 

TCBO), a monomer containing a high percentage of chlorine, is obtained from allyl alcohol and carbon tetrachloride (reaction 18.2) [18-23] ... 

The proposed hydride formation is conlirmed by the results of interaction with carbon tetrachloride. Reaction with CCI4 (equation 12.8) is a generally accepted test for metal-hydrogen (M-H) bonds (25). 

Hydrogen fluoride also effects replacement reactions in organic compounds. For example, carbon tetrachloride yields a mixture of chlorofluoromethanes CCI3F, CCI2F2 and so on. Like all the other hydrogen halides, hydrogen fluoride adds on to olefins, for example ... 

Chloroform and carbon tetrachloride must not be heated with metallic sodium as an explosive reaction is likely to take place (see footnote, p. 321). 

I. Isocyanide reaction. Repeat Test i for chloroform using i ml. of carbon tetrachloride in place of the chloroform. The odour of isocyanide can be detected only after heating gently for several minutes. 

Add 1 ml. of the alcohol-free ether to 0-1-0-15 g. of finely-powdered anhydrous zinc chloride and 0 5 g. of pure 3 5-dinitrobenzoyl chloride (Section 111,27,1) contained in a test-tube attach a small water condenser and reflux gently for 1 hour. Treat the reaction product with 10 ml. of 1-5N sodium carbonate solution, heat and stir the mixture for 1 minute upon a boiling water bath, allow to cool, and filter at the pump. Wash the precipitate with 5 ml. of 1 5N sodium carbonate solution and twice with 6 ml. of ether. Dry on a porous tile or upon a pad of filter paper. Transfer the crude ester to a test-tube and boil it with 10 ml. of chloroform or carbon tetrachloride filter the hot solution, if necessary. If the ester does not separate on cooling, evaporate to dryness on a water bath, and recrystallise the residue from 2-3 ml. of either of the above solvents. Determine the melting point of the resulting 3 5 dinitro benzoate (Section 111,27). 

Dissolve 5 g. of finely-powdered diazoaminobenzene (Section IV,81) in 12-15 g. of aniline in a small flask and add 2-5 g. of finely-powdered aniline hydrochloride (1). Warm the mixture, with frequent shaking, on a water bath at 40-45° for 1 hour. Allow the reaction mixture to stand for 30 minutes. Then add 15 ml. of glacial acetic acid diluted with an equal volume of water stir or shake the mixture in order to remove the excess of anihne in the form of its soluble acetate. Allow the mixture to stand, with frequent shaking, for 15 minutes filter the amino-azobenzene at the pump, wash with a little water, and dry upon filter paper Recrystallise the crude p-amino-azobenzene (3-5 g. m.p. 120°) from 15-20 ml. of carbon tetrachloride to obtain the pure compound, m.p. 125°. Alternatively, the compound may be recrystaUised from dilute alcohol, to which a few drops of concentrated ammonia solution have been added. 

Mix 31 g. (29-5 ml.) of benzyl alcohol (Section IV, 123 and Section IV,200) and 45 g. (43 ml.) of glacial acetic acid in a 500 ml. round-bottomed flask introduce 1 ml. of concentrated sulphuric acid and a few fragments of porous pot. Attach a reflux condenser to the flask and boil the mixture gently for 9 hours. Pour the reaction mixture into about 200 ml. of water contained in a separatory funnel, add 10 ml. of carbon tetrachloride (to eliminate emulsion formation owing to the slight difference in density of the ester and water, compare Methyl Benzoate, Section IV,176) and shake. Separate the lower layer (solution of benzyl acetate in carbon tetrachloride) and discard the upper aqueous layer. Return the lower layer to the funnel, and wash it successively with water, concentrated sodium bicarbonate solution (until effervescence ceases) and water. Dry over 5 g. of anhydrous magnesium sulphate, and distil under normal pressure (Fig. II, 13, 2) with the aid of an air bath (Fig. II, 5, 3). Collect the benzyl acetate a (colourless liquid) at 213-215°. The yield is 16 g. 

Triphenylchloromethane (C3Hj)3CCl is readily hydrolysed by warm water to triphenylcarbinol, thus providing an alternative method for the preparation of the latter. The former is conveniently obtained by the reaction between carbon tetrachloride and benzene in the presence of anhydrous aluminium ehloride ... 

Method 2. Place 90 g. of sodium benzenesulphonate (Section IV,29) (previously dried at 130-140° for 3 hours) and 50 g. of powdered phosphorus pentachloride (1) in a 500 ml. round-bottomed flask furnished with a reflux condenser heat the mixture in an oil bath at 170-180° for 12-15 hours. Every 3 hours remove the flask from the oil bath, allow to cool for 15-20 minutes, stopper and shake thoroughly until the mass becomes pasty. At the end of the heating period, allow the reaction mixture to cool. Pour on to 1 kilo of crushed ice. Extract the crude benzenesulphonyl chloride with 150 ml. of carbon tetrachloride and the aqueous layer with 75 ml. of the same solvent. Remove the solvent under atmospheric pressure and proceed as in Method 1. The yield is about 170 g., but depends upon the purity of the original sodium benzenesulphonate. 

Although no chemical reaction occurs, measurements of the freezing point and infra-red spectra show that nitric acid forms i i molecular complexes with acetic acid , ether and dioxan. In contrast, the infrared spectrum of nitric acid in chloroform and carbon tetrachloride - is very similar to that of nitric acid vapour, showing that in these cases a close association with the solvent does not occur. 

---