By thermal decomposition

Reboiler temperature increases with a limit often set by thermal decomposition of the material being vaporized, causing excessive fouling. 

B.p. — 29X. Monomer used to form polymers (only under rather drastic conditions) or copolymers with C2F4 and vinylidene fluoride, CH2 = CF2. Hexafluoropropene may be prepared by thermal decomposition of CF3CF2CF2C02Na or is prepared commercially by low pressure pyrolysis of C2F4. 

H2S is found with the reservoir gas and dissolved in the crude (< 50 ppm by weight), but it is formed during refining operations such as catalytic cracking, hydrodesulfurization, and thermal cracking or by thermal decomposition of sulfur[Pg.322]

Tellurium trioxide, TeOa, is an orange yellow powder made by thermal decomposition of telluric(VI) acid Te(OH)g. It is a strong oxidising agent which will, like H2Se04, oxidise hydrogen chloride to chlorine. It dissolves in hot water to give telluric(VI) acid. This is a weak acid and quite different from sulphuric and selenic acids. Two series of salts are known. 

It can be isolated by elecytrolysis of the fused cyanide and by a number of other methods. Very pure, gas-free cesium can be prepared by thermal decomposition of cesium azide. 

Ruthenium is a hard, white metal and has four crystal modifications. It does not tarnish at room temperatures, but oxidizes explosively. It is attacked by halogens, hydroxides, etc. Ruthenium can be plated by electrodeposition or by thermal decomposition methods. The metal is one of the most effective hardeners for platinum and palladium, and is alloyed with these metals to make electrical contacts for severe wear resistance. A ruthenium-molybdenum alloy is said to be... 

In agreement with the theory of polarized radicals, the presence of substituents on heteroaromatic free radicals can slightly affect their polarity. Both 4- and 5-substituted thiazol-2-yl radicals have been generated in aromatic solvents by thermal decomposition of the diazoamino derivative resulting from the reaction of isoamyl nitrite on the corresponding 2-aminothiazole (250,416-418). Introduction in 5-position of electron-withdrawing substituents slightly enhances the electrophilic character of thiazol-2-yl radicals (Table 1-57). 

The evidence obtained in compaction experiments is of particular interest in the present context. Figure 3.22 shows the results obtained by Avery and Ramsay for the isotherms of nitrogen on compacts of silica powder. The hysteresis loop moved progressively to the left as the compacting pressure increased, but the lower closure point did not fall below a relative pressure of 0-40. Similar results were obtained in the compaction of zirconia powder both by Avery and Ramsay (cf. Fig. 4.5), and by Gregg and Langford, where the lower closure point moved down to 0-42-0-45p° but not below. With a mesoporous magnesia (prepared by thermal decomposition of the hydrated carbonate) the position of the closure point... 

The Acetic Acid Process. Prior to the energy crisis of the 1970s, acetic anhydride was manufactured by thermal decomposition of acetic acid at pressures of 15—20 kPa (2.2—2.9 psi) (22), beginning with the first step ... 

Phosphoms oxyfluoride is a colorless gas which is susceptible to hydrolysis. It can be formed by the reaction of PF with water, and it can undergo further hydrolysis to form a mixture of fluorophosphoric acids. It reacts with HF to form PF. It can be prepared by fluorination of phosphoms oxytrichloride using HF, AsF, or SbF. It can also be prepared by the reaction of calcium phosphate and ammonium fluoride (40), by the oxidization of PF with NO2CI (41) and NOCl (42) in the presence of ozone (43) by the thermal decomposition of strontium fluorophosphate hydrate (44) by thermal decomposition of CaPO F 2H20 (45) and reaction of SiF and P2O5 (46). 

Carbonization. Next to combustion, carbonization represents one of the largest uses of coal (2,24—26). Carbonization is essentially a process for the production of a carbonaceous residue by thermal decomposition, accompanied by simultaneous removal of distillate, of organic substances. 

Silane, pure or doped, is used to prepare semiconducting siUcon by thermal decomposition at >600° C. Gaseous dopants such as germane, arsine, or diborane maybe added to the silane at very low concentrations in the epitaxial growing of semiconducting siUcon for the electronics industry. Higher silanes, eg, Si H and Si Hg, are known but are less stable than SiH. These are analogues of lower saturated hydrocarbons. 

Germane is used primarily to produce high purity germanium metal or epitaxial deposits of germanium on substrates for electronics by thermal decomposition at about 350°C (see Germaniumand germanium compounds). 

Lithium Oxide. Lithium oxide [12057-24-8], Li20, can be prepared by heating very pure lithium hydroxide to about 800°C under vacuum or by thermal decomposition of the peroxide (67). Lithium oxide is very reactive with carbon dioxide or water. It has been considered as a potential high temperature neutron target for tritium production (68). 

Rhenium Halides and Halide Complexes. Rhenium reacts with chlorine at ca 600°C to produce rheniumpentachloride [39368-69-9], Re2Cl2Q, a volatile species that is dimeric via bridging hahde groups. Rhenium reacts with elemental bromine in a similar fashion, but the metal is unreactive toward iodine. The compounds ReCl, ReBr [36753-03-4], and Rel [59301-47-2] can be prepared by careful evaporation of a solution of HReO and HX. Substantiation in a modem laboratory would be desirable. Lower oxidation state hahdes (Re X ) are also prepared from the pentavalent or tetravalent compounds by thermal decomposition or chemical reduction. 

Bitumen is a hydrogen-deficient oil that is upgraded by carbon removal (coking) or hydrogen addition (hydrocrackiag) (2,4). There are two methods by which bitumen conversion can be achieved by direct heating of mined tar sand and by thermal decomposition of separated bitumen. The latter is the method used commercially, but the former has potential for commercialisation (see Fuels, SYNTHETIC). 

Titanium Dibromide. Titanium dibromide [13873-04-5] a black crystalline soHd, density 4310 kg/m, mp 1025°C, has a cadmium iodide-type stmcture and is readily oxidized to trivalent titanium by water. Spontaneously flammable in air (142), it can be prepared by direct synthesis from the elements, by reaction of the tetrabromide with titanium, or by thermal decomposition of titanium tribromide. This last reaction must be carried out either at or below 400°C, because at higher temperatures the dibromide itself disproportionates. 

For solvent extraction of pentavalent vanadium as a decavanadate anion, the leach solution is acidified to ca pH 3 by addition of sulfuric acid. Vanadium is extracted in about four countercurrent mixer—settler stages by a 3—5 wt % solution of a tertiary alkyl amine in kerosene. The organic solvent is stripped by a soda-ash or ammonium hydroxide solution, and addition of ammoniacal salts to the rich vanadium strip Hquor yields ammonium metavanadate. A small part of the metavanadate is marketed in that form and some is decomposed at a carefully controlled low temperature to make air-dried or fine granular pentoxide, but most is converted to fused pentoxide by thermal decomposition at ca 450°C, melting at 900°C, then chilling and flaking. 

Semiconductor and Solar Cells. High purity (up to 99.9%) antimony has a limited but important appHcation in the manufacture of semiconductor devices (see Semiconductors). It may be obtained by reduction of a chemically purified antimony compound with a high purity gaseous or soHd reductant, or by thermal decomposition of stibine. The reduced metal may be further purified by pyrometaHurgical and zone melting techniques. 

Barium nitrite [13465-94-6] Ba(N02)2, crystallines from aqueous solution as barium nitrite monohydrate [7787-38-4], Ba(N02)2 H2O, which has yellowish hexagonal crystals, sp gr 3.173, solubihty 54.8 g Ba(NO2)2/100 g H2O at 0°C, 319 g at 100°C. The monohydrate loses its water of crystallization at 116°C. Anhydrous barium nitrite, sp gr 3.234, melts at 267°C and decomposes at 270 °C into BaO, NO, and N2. Barium nitrite may be prepared by crystallization from a solution of equivalent quantities of barium chloride and sodium nitrite, by thermal decomposition of barium nitrate in an atmosphere of NO, or by treating barium hydroxide or barium carbonate with the gaseous oxidiation products of ammonia. It has been used in diazotization reactions. 

Beryllium Oxalate. BeryUium oxalate trihydrate [15771 -43-4], BeC204 -3H20, is obtained by evaporating a solution of beryUium hydroxide or oxide carbonate in a slight excess of oxaHc acid. The compound is very soluble in water. Beryllium oxalate is important for the preparation of ultrapure beryllium hydroxide by thermal decomposition above 320°C. The latter is frequentiy used as a standard for spectrographic analysis of beryUium compounds. 

Propyne [74-99-7] 3 4 obtained from Mg2C2, which probably contains the C3 ion, and it is also formed by thermal decomposition of MgC2, with separation of graphite ... 

Emerging technologies for the commercial manufacture of chloric acid fall into three categories (/) generation of high purity chloric acid by thermal decomposition of pure solutions of hypochlorous acid [7790-92-3], HCIO (5). 

Tetrachloroethylene was first prepared ia 1821 by Faraday by thermal decomposition of hexachloroethane. Tetrachloroethylene is typically produced as a coproduct with either trichloroethylene or carbon tetrachloride from hydrocarbons, partially chloriaated hydrocarbons, and chlorine. Although production of tetrachloroethylene and trichloroethylene from acetylene was once the dominant process, it is now obsolete because of the high cost of acetylene. Demand for tetrachloroethylene peaked ia the 1980s. The decline ia demand can be attributed to use of tighter equipment and solvent recovery ia the dry-cleaning and metal cleaning iadustries and the phaseout of CFG 113 (trichlorotrifluoroethane) under the Montreal Protocol. 

---