3- ?-Butylcyclohexanone

On the other hand, enantioselective conjugate addition to 2-cyclohexenone with lithium dibutylcuprates (having a noncova-lently bound chiral phosphorus ligand derived from ephedrine) affords 3-butylcyclohexanone with up to 76% ee (eq 14). ... 

The method is useful in the preparation of other axial alcohols. Henbest has reported the reductions of 3- butylcyclohexanone, 3,3,5-trimethylcyclohexanone, and cholestanone to the axial alcohols by this procedure, although for the preparation of 3-a-cholestanol the procedure of Edward is preferred by the checkers. Recently 2,4,4-trimethylcyclohexanone has been reduced to the pure axial alcohol by this method in 90% yield. 

An ethereal soln. of 2-cyclohexenone added to Li-di-n-buty Icupr ate complex prepared from tri-n-butylphosphine-CuLcomplex and n-butyllithium in ether-hexane at -78° for 0.5 hr., stirred 0.5 hr. at the same temp., acetyl chloride in ether and hexamethylphosphoramide added rapidly at 0°, and stirred 4 hrs. at room temp. 2-acetyl-3- -butylcyclohexanone. Y 92%. F. e. s. T. Tanaka et al., Tetrah. Let. 1975, 1535 reactions with organocopper compds., review, s. J. P. Marino, Ann. Rep. Med. Chem. 10, 327 (1975). 

In a dry flask, copper iodide (0.13 mmol) and the ligand 155 (0.54 mmol) are suspended in diethyl ether (13 mL). The suspension is stirred 20 min at 25 °C and then cooled to -78 °C. n-Butylmagnesium chloride (2.0 mmol, solution in diethyl ether) is added, and the mixture stirred for 15 min before a solution of 2-cyclohexenone (156 1.7 mmol) in diethyl ether (4 mL) is dropwise added over 20 min. The reaction mixture is stirred 20 min at -78 °C and worked up in the usual manner. Purification by column chromatography (CH2Cl2/hexane 4 1) followed by short-path distillation afford (-)-(S)-3-butylcyclohexanone (157 92%, 90% ee). The enantiomeric excess is determined by C NMR analysis of the corresponding diastereomeric ketals prepared with (R,R)-2,3-butandiol. ... 

Addition of phenylmagnesium bromide to 4 tert butylcyclohexanone gives two isomeric ter tiary alcohols as products Both alcohols yield the same alkene when subjected to acid catalyzed dehydration Suggest reasonable structures for these two alcohols... 

The stereoselective reactions in Scheme 2.10 include one example that is completely stereoselective (entry 3), one that is highly stereoselective (entry 6), and others in which the stereoselectivity is modest to low (entries 1,2,4, 5, and 7). The addition of formic acid to norbomene (entry 3) produces only the exo ester. Reduction of 4-r-butylcyclohexanone (entry 6) is typical of the reduction of unhindered cyclohexanones in that the major diastereomer produced has an equatorial hydroxyl group. Certain other reducing agents, particularly sterically bulky ones, exhibit the opposite stereoselectivity and favor the formation of the diastereomer having an axial hydroxyl groi. The alkylation of 4-t-butylpiperidine with benzyl chloride (entry 7) provides only a slight excess of one diastereomer over the other. 

Iodine fluoride is a more versatile reagent than molecular fluorine in geminal fluorination of other hydrazones and related compounds under milder reaction conditions [55] Substrates fluorinated include hydrazones of simple cyclic or steroidal ketones (e g, 4 tert butylcyclohexanone, 70%, 3 cholestanone, 70%), W methyl and A/N dimethylhydrazones [R2C=NNH(CH3) 70%, R2C=NNC(CH3)2, 50%], semicarbazones (R2C=NNHCONH2, 25-50%), and 2,4-dinitrophenylhy-drazones [R2C==NNH-C6H3-2,4(N02)2, 25-50%]... 

That the methyl group in the pyrrolidine enamine of 2-methylcyclo-hexanone (7) is in fact axial was demonstrated by Johnson and Whitehead (8). They found that careful hydrolysis of the pyrrolidine enamine of the conformationally more stable system, i.e., 2-methyI-4-t-butylcyclohexanone (13), led to a 1 4 mixture of cis and trans isomers of the ketone (14 and 15), showing that the methyl group in the enamine is largely in the axial orientation. 

Since the conformational inversion of 2c-methylcyclohexanone is the key step in this sequence, the corresponding conformationally more stable system, i.e., cw-2-methyl-4-t-butylcyclohexanone (14), should fail to incorporate any deuterium. This was actually shown to be the case. Treatment of this ketone under identical conditions for d exchange did not show any d incorporation. This evidence also rules out the likelihood of any d incorporation via acid- or base-catalyzed enolization. 

Interestingly the pyrrolidine enamine of 3-t-butylcyclohexanone (41) consists of a 3 2 mixture of A and A isomers (79 and 80). The preference for the A isomer in this case is due to the relief of two of the four skew butane interactions, which are present in the isomer. The A isomer, owever, contains two additional interactions, i.e., one modified skew utane interaction 0.4 kcal/mole (42) and one interaction between c C-2 vinylic hydrogen atom and the ethyl portion of the t-butyl group hich is pointed toward it. 

The yields ranged from 55% for the mixture of enamines formed from morpholine and methylisopropyl ketone to 94% for the enamine formed from dimethylamine and methyl t-butyl ketone. The hindered ketone 2,5-dimethylcyclopentanone could be converted to an enamine, but the more hindered ketone, 2,6-di-t-butylcyclohexanone, was inert. White and Weingarten 43) attribute the effectiveness of titanium tetrachloride in this reaction to its ability to scavenge water and to polarize the carbonyl bond. 

Stereoselective epoxidation can be realized through either substrate-controlled (e.g. 35 —> 36) or reagent-controlled approaches. A classic example is the epoxidation of 4-t-butylcyclohexanone. When sulfonium ylide 2 was utilized, the more reactive ylide irreversibly attacked the carbonyl from the axial direction to offer predominantly epoxide 37. When the less reactive sulfoxonium ylide 1 was used, the nucleophilic addition to the carbonyl was reversible, giving rise to the thermodynamically more stable, equatorially coupled betaine, which subsequently eliminated to deliver epoxide 38. Thus, stereoselective epoxidation was achieved from different mechanistic pathways taken by different sulfur ylides. In another case, reaction of aldehyde 38 with sulfonium ylide 2 only gave moderate stereoselectivity (41 40 = 1.5/1), whereas employment of sulfoxonium ylide 1 led to a ratio of 41 40 = 13/1. The best stereoselectivity was accomplished using aminosulfoxonium ylide 25, leading to a ratio of 41 40 = 30/1. For ketone 42, a complete reversal of stereochemistry was observed when it was treated with sulfoxonium ylide 1 and sulfonium ylide 2, respectively. ... 

The mixture is decanted into an Erlenmeyer flask, the residual green salts are washed with two 15-ml portions of acetone, and the washings are added to the main acetone solution. Cautiously, sodium bicarbonate (approx. 13 g) is added to the solution with swirling until the pH of the reaction mixture is neutral. The suspension is filtered, and the residue is washed with 10-15 ml of acetone. The filtrate is transferred to a round-bottom flask and concentrated on a rotary evaporator under an aspirator while the flask temperature is maintained at about 50°. The flask is cooled and the residue transferred to a separatory funnel, (If solidification occurs, the residue may be dissolved in ether to effect the transfer.) To the funnel is added 100 ml of saturated sodium chloride solution, and the mixture is extracted with two 50-ml portions of ether. The ether extracts are combined, washed with several 5-ml portions of water, dried over anhydrous magnesium sulfate, and filtered into a round-bottom flask. The ether may be distilled away at atmospheric pressure (steam bath) or evaporated on a rotary evaporator. On cooling, the residue should crystallize. If it does not, it may be treated with 5 ml of 30-60° petroleum ether, and crystallization may be induced by cooling and scratching. The crystalline product is collected by filtration and recrystallized from aqueous methanol. 4-r-Butylcyclohexanone has mp 48-49° (yield 60-90 %). 

The dropping funnel is charged with a solution of 7.7 g (0.05 mole) of 4-/-butylcyclo-hexanone (Chapter 1, Section 1) in 50 ml of dry ether. The solution is slowly added to the mixed hydride solution at a rate so as to maintain a gentle reflux. The reaction mixture is then refluxed for an additional 2 hours. Excess hydride is consumed by the addition of 1 ml of dry t-butyl alcohol, and the mixture is refluxed for 30 minutes more. 4-/-Butylcyclohexanone (0.3 g) in 5 ml of dry ether is added to the reaction mixture, and refluxing is continued for 4 hours. The cooled (ice bath) reaction mixture is decomposed by the addition of 10 ml of water followed by 25 ml of 10% aqueous sulfuric acid. The ether layer is separated, and the aqueous layer is extracted with 20 ml of ether. The combined ether extracts are washed with water and dried over anhydrous magnesium sulfate. After filtration, the ether is removed (rotary evaporator), and the residue... 

To a solution of 1.0 g (0.003 mole) of iridium tetrachloride in 0.5 ml of concentrated hydrochloric acid is added 15 ml of trimethylphosphite. This solution is added to a solution of 7.7 g (0.05 mole) of 4-/-butylcyclohexanone in 160 ml of isopropanol in a 500-ml flask equipped with a reflux condenser. The solution is refluxed for 48 hours, then cooled, and the isopropanol is removed on a rotary evaporator. The residue is diluted with 65 ml of water and extracted four times with 40-ml portions of ether. The extracts are dried with anhydrous magnesium sulfate, filtered, and the ether is removed on the rotary evaporator. The white solid residue is recrystallized from 60 % aqueous ethanol affording cis alcohol of greater than 99% purity, mp 82-83.5°. 

Hydrogenation of the constrained 4-r-butylcyclohexanone gives 99% ether (97% cis) in ethanol over palladium (68). High yields of methyl ethers are formed by reduction of 5a- and 5 -cholestan-3-ones in methanol over palladium. 

Examples of palladium-catalyzed reduction are 4-chloro-2,6-di-r-butyl-phenol to 2,6-di-t-butylcyclohexanone (750 psig, 25 C) with loss of halogen 24), 1,8-dihydroxynaphthalene to 8-hydroxy-1-tetralone 30), and 2,4-dimethylphenol to 2,4-dimethylcyclohexanone (27). 

The procedure employs a readily available starting material and produces the pure trans isomer in high yield. The method described is an improvement on that used by Eliel and Rerick2 in that it is not necessary to use a clear solution of lithium aluminum hydride in ether for the preparation of the mixed hydride. It is not necessary to know the precise amount of lithium aluminum hydride used so long as a slight excess is present. The excess hydride is destroyed by adding /-butanol the excess /-butanol has no effect on the subsequent equilibration and purification. The equilibration of the 4 / butylcyclohexanol is effected by adding a small amount of 4-/-butylcyclohexanone. 

Red phosphorus in bromination of 7 butj rolactone 46, 22 Reduction, of 3/3 acetoxy 5 pregnene 20-one with lithium aluminum tn t butoxyhydnde, 46, 57 of 4-f butylcyclohexanone with lithium aluminum hydride aluminum chloride, 47,16... 

Simple allyl alkali metal compounds have only a small capability for discriminating between diastereotopic faces of carbonyl compounds. Although a matter of simple diastereoselectivity, this can be concluded from the reaction of conformationally locked 4-/erf-butylcyclohexanone... 

In contrast, the tin(Il) enolates of cyclohexanone undergo addition to (2f)-(2-nitroethenyl)ben-zene to give 2-(2-nitro-l-phenylethyl)cyclohexanones with high anti diastereoselection5. The analogous reactions with cyclopentanone and 4-tert-butylcyclohexanone were less diastereose-lective with anti/syn ratios of 70 30 and 62 38. respectively. Modest to excellent diastereoselec-tivity was observed with acyclic ketones (d.r. 75 25 to 90 10) however the precise stereochemical details were not provided. 

POLYMERIC CARBODIIMIDE. II. MOFFAT OXIDATION 4-tert-BUTYLCYCLOHEXANONE... 

---