Distillation azeotrope

Mixtures with low relative volatility or which exhibit azeotropic behavior. The most common means of dealing with the separation of low-relative-volatility and azeotropic mixtures is to use extractive or azeotropic distillation. These processes are considered in detail later. Crystallization and liquid-liquid extraction also can be used. 

In the first class, azeotropic distillation, the extraneous mass-separating agent is relatively volatile and is known as an entrainer. This entrainer forms either a low-boiling binary azeotrope with one of the keys or, more often, a ternary azeotrope containing both keys. The latter kind of operation is feasible only if condensation of the overhead vapor results in two liquid phases, one of which contains the bulk of one of the key components and the other contains the bulk of the entrainer. A t3q)ical scheme is shown in Fig. 3.10. The mixture (A -I- B) is fed to the column, and relatively pure A is taken from the column bottoms. A ternary azeotrope distilled overhead is condensed and separated into two liquid layers in the decanter. One layer contains a mixture of A -I- entrainer which is returned as reflux. The other layer contains relatively pure B. If the B layer contains a significant amount of entrainer, then this layer may need to be fed to an additional column to separate and recycle the entrainer and produce pure B. 

Figure 3.10 A typical azeotropic distillation using an entrainer.

The second class of distillation operation using an extraneous mass-separating agent is extractive distillation. Here, the extraneous mass-separating agent is relatively involatile and is known as a solvent. This operation is quite different from azeotropic distillation in that the solvent is withdrawn from the column bottoms and does not form an azeotrope with any of the components. A typical extractive distillation process is shown in Fig. 3.11. ... 

As with azeotropic distillation, the separation is possible in extractive distillation because the extraneous mass-separating agent interacts more strongly with one of the components than the other. This in turn alters in a favorable way the relative volatility between the key components. 

In principle, extractive distillation is more useful than azeotropic distillation because the process does not depend on the accident of azeotrope formation, and thus a greater choice of mass-separating agent is, in principle, possible. In general, the solvent should have a chemical structure similar to that of the less volatile of the two components. It will then tend to form a near-ideal mixture with the less volatile component and a nonideal mixture with the more volatile component. This has the effect of increasing the volatility of the more volatile component. 

Wastewater leaves the process from the bottom of the second column and the decanter of the azeotropic distillation column. Although both these streams are essentially pure water, they will nevertheless contain small quantities of organics and must be treated before final discharge. This treatment can be avoided altogether by recycling the wastewater to the reactor inlet to substitute part of the freshwater feed (see Fig. 10.36). 

Absolute Ethanol.. Supplies ot iibsolutc cthnnol, which is frec ucntly required in <>rj> mic chemiciil work, nrc now freely iiwiihible commercially as a result of azeotropic distillation methods. If however it should be... 

The formation of ethyl isopropylidene cyanoacetate is an example of the Knoevenagel reaction (see Discussion before Section IV,123). With higher ketones a mixture of ammonium acetate and acetic acid is an effective catalyst the water formed is removed by azeotropic distillation with benzene. The essential step in the reaction with aqueous potassium cyanide is the addition of the cyanide ion to the p-end of the ap-double bond ... 

Nitromethane is a very common material. Just go down to your local drag strip and pick up a gallon or two for doping your high performance cars fuel. It s also available up to 40% pure in RC model fuels. Simply fractionally distill the nitromethane (bp 101°C) out of the model fuel mixture and you re ready to go. If methanol Is present in the fuel formulation, some will azeotropically distill over with the nitromethane lowering its boiling point slightly, but this does not present a problem. 

Diols that bear two hydroxyl groups m a 1 2 or 1 3 relationship to each other yield cyclic acetals on reaction with either aldehydes or ketones The five membered cyclic acetals derived from ethylene glycol (12 ethanediol) are the most commonly encoun tered examples Often the position of equilibrium is made more favorable by removing the water formed m the reaction by azeotropic distillation with benzene or toluene... 

Because of this parallel with liquid-vapor equilibrium, copolymers for which ri = l/r2 are said to be ideal. For those nonideal cases in which the copolymer and feedstock happen to have the same composition, the reaction is called an azeotropic polymerization. Just as in the case of azeotropic distillation, the composition of the reaction mixture does not change as copolymer is formed if the composition corresponds to the azeotrope. The proportion of the two monomers at this point is given by Eq. (7.19). 

The choice of separation method to be appHed to a particular system depends largely on the phase relations that can be developed by using various separative agents. Adsorption is usually considered to be a more complex operation than is the use of selective solvents in Hquid—Hquid extraction (see Extraction, liquid-liquid), extractive distillation, or azeotropic distillation (see Distillation, azeotropic and extractive). Consequentiy, adsorption is employed when it achieves higher selectivities than those obtained with solvents. 

Anhydrous Acetic Acid. In the manufacture of acetic acid by direct oxidation of a petroleum-based feedstock, solvent extraction has been used to separate acetic acid [64-19-7] from the aqueous reaction Hquor containing significant quantities of formic and propionic acids. Isoamyl acetate [123-92-2] is used as solvent to extract nearly all the acetic acid, and some water, from the aqueous feed (236). The extract is then dehydrated by azeotropic distillation using isoamyl acetate as water entrainer (see DISTILLATION, AZEOTROPIC AND EXTRACTIVE). It is claimed that the extraction step in this process affords substantial savings in plant capital investment and operating cost (see Acetic acid and derivatives). A detailed description of various extraction processes is available (237). 

Maleic acid can be thermally dehydrated to maleic anhydride (69) or dehydrated through azeotropic distillation. Solvents such as xylenes (70) or dibutyl phthalate [84-74-2] (71) are preferred but conditions must be carefully adjusted to avoid isomerization to fumaric acid. 

Azeotropic and Extractive Distillations. Effective as they are for producing various Hquid fractions, distillation units generally do not produce specific fractions. In order to accommodate the demand for such products, refineries have incorporated azeotropic distillation and extractive distillation in their operations (see Distillation, azeotropic and extractive). 

---