Anhydrides from carboxylic acid salts

Acid Anhydrides from Carboxylic Acid Salts and Acid Halides 2.133 Acid Anhydrides by Miscellaneous Methods... 

Fallacious acetate I triphenylphosphine I sodium salt Carboxylic acid anhydrides from carboxylic acid salts and iodides Carbonylation under mild conditions... 

Unsymmetrical as well as symmetrical anhydrides are often prepared by the treatment of an acyl halide with a carboxylic acid salt. The compound C0CI2 has been used as a catalyst. If a metallic salt is used, Na , K , or Ag are the most common cations, but more often pyridine or another tertiary amine is added to the free acid and the salt thus formed is treated with the acyl halide. Mixed formic anhydrides are prepared from sodium formate and an aryl halide, by use of a solid-phase copolymer of pyridine-l-oxide. Symmetrical anhydrides can be prepared by reaction of the acyl halide with aqueous NaOH or NaHCOa under phase-transfer conditions, or with sodium bicarbonate with ultrasound. 

Anhydrides can be formed from certain carboxylic acid salts for example, by treatment of trimethylammonium carboxylates with phosgene ... 

By use of TV-(trifluoroacetyl)- or TV-(trichloroacetyl)-imidazoleare obtained symmetric aliphatic and aromatic anhydrides even from carboxylic acids that do not form insoluble salts in benzene, ether, or THF (Table 13—1). In this case the acid is treated with the imidazolide in a 2 1 molar ratio, and an insoluble imidazolium trifluoro- or tri-chloroacetate is formed. 

Preparation of acid anhydrides Acid anhydrides are prepared from carboxylic acids by the loss of water. For example, acetic anhydride is prepared industrially by heating acetic acid to 800 °C. Other anhydrides are difficult to prepare directly from the corresponding carboxylic acids. Usually they are prepared from acid chloride and sodium carboxylate salt (see below). 

Monocationic acyl ions are readily prepared as persistent species in solutions of low nucleophile strength.68 These acyl ions have been thoroughly characterized by IR and NMR spectroscopy, and several acyl ion salts have been characterized by X-ray crystallography. The monocationic acyl ions are often prepared in situ from carboxylic acids, esters, or anhydrides, by the action of a strong Brpnsted acid, or the ions can be prepared from ionization of an appropriate acid halide with a strong Lewis acid. Both methods have been used to prepare acyl-centered dications, some of which can be considered distonic superelectrophiles. As described previously, dicarboxylic acids cleave to the bis-acyl ions in superacid (FSChH-SbFs) provided that the acyl cations are separated by at least three methylene units (eq 54).55 The first bis-acyl dications were reported by Olah and Comisarow, being prepared by the reactions of dicarboxylic acid fluorides with superacidic SbFs (eq 72).69... 

Given a particular anhydride, write an equation for its preparation from an acid chloride and a carboxylic acid salt. 

The six common groups derived from carboxylic acids are, in decreasing priority after carboxylic acids salts, anhydrides, esters, acyl halides, amides, and nitriles. 

Acid anhydrides are synthesized from acid chlorides and carboxylic acid salts. 

Carboxylic acid anhydrides from quarternary ammonium salts... 

Anhydrides of carboxylic acids are best prepared by the classical method of treating acid chlorides with salts of acids, a method that can be used equally for preparing mixed anhydrides. The salt may be replaced by the free acid if pyridine is added to the reaction mixture. Further, water may be removed directly from carboxylic acids, either by heat in certain cases where aliphatic or aromatic dicarboxylic acids give cyclic anhydrides, or by means of acetic anhydride or acetyl chloride. 

The synthesis of key intermediate 12, in optically active form, commences with the resolution of racemic trans-2,3-epoxybutyric acid (27), a substance readily obtained by epoxidation of crotonic acid (26) (see Scheme 5). Treatment of racemic 27 with enantio-merically pure (S)-(-)-1 -a-napthylethylamine affords a 1 1 mixture of diastereomeric ammonium salts which can be resolved by recrystallization from absolute ethanol. Acidification of the resolved diastereomeric ammonium salts with methanesulfonic acid and extraction furnishes both epoxy acid enantiomers in eantiomerically pure form. Because the optical rotation and absolute configuration of one of the antipodes was known, the identity of enantiomerically pure epoxy acid, (+)-27, with the absolute configuration required for a synthesis of erythronolide B, could be confirmed. Sequential treatment of (+)-27 with ethyl chloroformate, excess sodium boro-hydride, and 2-methoxypropene with a trace of phosphorous oxychloride affords protected intermediate 28 in an overall yield of 76%. The action of ethyl chloroformate on carboxylic acid (+)-27 affords a mixed carbonic anhydride which is subsequently reduced by sodium borohydride to a primary alcohol. Protection of the primary hydroxyl group in the form of a mixed ketal is achieved easily with 2-methoxypropene and a catalytic amount of phosphorous oxychloride. 

A dispersant that can be used in drilling fluids, spacer fluids, cement slurries, completion fluids, and mixtures of drilling fluids and cement slurries controls the rheologic properties of and enhances the filtrate control in these fluids. The dispersant consists of polymers derived from monomeric residues, including low-molecular-weight olefins that may be sulfonated or phosphonated, unsaturated dicarboxylic acids, ethylenically unsaturated anhydrides, unsaturated aliphatic monocarboxylic acids, vinyl alcohols and diols, and sulfonated or phosphonated styrene. The sulfonic acid, phosphonic acid, and carboxylic acid groups on the polymers may be present in neutralized form as alkali metal or ammonium salts [192,193]. 

Another Pd-catalyzed reaction of aryl- and alkylzinc halides used carboxylic anhydrides as starting organic compounds (Scheme 127).328 One of the advantages of this method is that anhydrides can be synthesized in situ from the corresponding sodium salts of carboxylic acids and ethyl chloroformate. The scope of the method includes aliphatic and aromatic anhydrides, phenyl-, ethyl-, isopropyl-, and n-butylzinc iodides. 

The key to a controlled molecular weight build-up, which leads to the control of product properties such as glass transition temperature and melt viscosity, is the use of a molar excess of diisopropanolamine as a chain stopper. Thus, as a first step in the synthesis process, the cyclic anhydride is dosed slowly to an excess of amine to accommodate the exothermic reaction and prevent unwanted side reactions such as double acylation of diisopropanolamine. HPLC analysis has shown that the reaction mixture after the exothermic reaction is quite complex. Although the main component is the expected acid-diol, unreacted amine and amine salts are still present and small oligomers already formed. In the absence of any catalyst, a further increase of reaction temperature to 140-180°C leads to a rapid polycondensation. The expected amount of water is distilled (under vacuum, if required) from the hot polymer melt in approximately 2-6 h depending on the anhydride used. At the end of the synthesis the concentration of carboxylic acid groups value reaches the desired low level. 

---