Amino resins urea melamine

Molded amino resins (urea, melamine) Benzylamine (at 160°C) All common solvents... 

Amino Resins. Urea, melamine, and benzoguanamine resins react with high molecular mass epoxy resins on heating. Their hydroxymethyl groups react with one another and with the hydroxyl groups of the epoxy resins to form ether bonds. Such systems are used for coating domestic appliances as well as for packaging. 

Urea. Urea (carbamide) CH4N2O, is the most important building block for amino resins because urea—formaldehyde is the largest selling amino resin, and urea is the raw material for melamine, the amino compound used in the next largest selling type of amino resin. Urea is also used to make a variety of other amino compounds, such as ethyleneurea, and other cyclic derivatives used for amino resins for treating textiles. They are discussed later. 

UREA-FORMALDEHYDE RESIN. An important class of amino resin. Urea and formaldehyde are united in a two-stage process in the presence of pyridine, ammonia, or certain alcohols with heat and control of pH to form intermediates (methylolurea, dimenthylolurea) that are mixed with fillers to produce molding powders. These are converted to thermosetting resins by further controlled heating and pressure in the presence of catalysts. These were first plastics that could be made in white, pastel, and colored products. See also Amino Acids Melamine. 

Developments in coatings technology have been reflected in the types of amino resins used. Melamines have grown in general at the expense of ureas, and the higher solids, more monomeric melamines have grown at the expense of conventional polymeric melamines. 

Polymerizations with Formaldehyde Amino Resins (Urea and Melamine) and Phenolics... 

Uses. The principal use of adiponitrile is for hydrogenation to hexamethylene diamine leading to nylon-6,6. However, as a result of BASE s new adiponitrile-to-caprolactam process, a significant fraction of ADN produced may find its way into nylon-6 production. Adipoquanamine, which is prepared by the reaction of adiponitrile with dicyandiamide [461-58-5] (cyanoguanidine), may have uses in melamine—urea amino resins (qv) (see "Benzonitrile, Uses"). Its typical Hquid nitrile properties suggest its use as an extractant for aromatic hydrocarbons. 

Urea is also used as feed supplement for mminants, where it assists in the utilization of protein. Urea is one of the raw materials for urea—formaldehyde resins. Urea (with ammonia) pyrolyzes at high temperature and pressure to form melamine plastics (see also Cyanamides). Urea is used in the preparation of lysine, an amino acid widely used in poultry feed (see Amino acids Feeds and feed additives, petfoods). It also is used in some pesticides. 

Amino and Phenolic Resins. The largest use of formaldehyde is in the manufacture of urea—formaldehyde, phenol—formaldehyde, and melamine—formaldehyde resins, accounting for over one-half (51%) of the total demand (115). These resins find use as adhesives for binding wood products that comprise particle board, fiber board, and plywood. Plywood is the largest market for phenol—formaldehyde resins particle board is the largest for urea—formaldehyde resins. Under certain conditions, urea—formaldehyde resins may release formaldehyde that has been alleged to create health or environmental problems (see Amino RESINS AND PLASTICS). 

Polymers. AH nitro alcohols are sources of formaldehyde for cross-linking in polymers of urea, melamine, phenols, resorcinol, etc (see Amino RESINS AND PLASTICS). Nitrodiols and 2-hydroxymethyl-2-nitro-l,3-propanediol can be used as polyols to form polyester or polyurethane products (see Polyesters Urethane polymers). 2-Methyl-2-nitro-l-propanol is used in tires to promote the adhesion of mbber to tire cord (qv). Nitro alcohols are used as hardening agents in photographic processes, and 2-hydroxymethyl-2-nitro-l,3-propanediol is a cross-linking agent for starch adhesives, polyamides, urea resins, or wool, and in tanning operations (17—25). Wrinkle-resistant fabric with reduced free formaldehyde content is obtained by treatment with... 

Catalysts. The alkanolamines continue to find use as blocked catalysts for textile resins, coatings resins, adhesives, etc. Of particular utifity in curing durable-press textiles is AMP-HCl. Other salts, such as those of the benzoin tosylate or A-toluenesulfonic acid, find utifity in melamine- or urea-based coatings (18) (see Amino resins and plastics). 

Amino resins are thermosetting polymers made by combining an aldehyde with a compound containing an amino (—NH2) group. Urea—formaldehyde (U/F) accounts for over 80% of amino resins melamine—formaldehyde accounts for most of the rest. Other aldehydes and other amino compounds are used to a very minor extent. The first commercially important amino resin appeared about 1930, or some 20 years after the introduction of phenol—formaldehyde resins and plastics (see Phenolic resins). 

Melamine. Melamine (cyanurotriamide, 2,4,6-ttiainino-j -triazine) C H N, is a white crystalline soHd, melting at approximately 350°C with vaporization, only slightly soluble in water. The commercial product, recrystallized grade, is at least 99% pure. Melamine was synthesized eady in the development of organic chemistry, but it remained of theoretical interest until it was found to be a usehil constituent of amino resins. Melamine was first made commercially from dicyandiamide [461-58-5] (see Cyanamides), but is now made from urea, a much cheaper starting material (9—12) (see also... 

Since melamine resins are derived from urea, they are more cosdy and are therefore restricted to appHcations requiring superior performance. Essentially ad of the melamine produced is used for making amino resins and plastics. 

A wide selection of amino resin compositions is commercially available. They are all alkylated to some extent in order to provide compatibiUty with the other film formers, and formulation stabiUty. They vary not only in the type of amine (melamine, urea, ben2oguanamine, and glycolutil) used, but also in the concentration of combined formaldehyde, and the type and concentration of alkylation alcohol (/ -butanol, isobutyl alcohol, methanol). 

Most amino resins used commercially for finishing textile fabrics are methylolated derivatives of urea or melamine. Although these products are usually monomeric, they may contain some polymer by-product. 

Both urea— and melamine—formaldehyde resins are of low toxicity. In the uncured state, the amino resin contains some free formaldehyde that could be objectionable. However, uncured resins have a very unpleasant taste that would discourage ingestion of more than trace amounts. The molded plastic, or the cured resin on textiles or paper may be considered nontoxic. Combustion or thermal decomposition of the cured resins can evolve toxic gases, such as formaldehyde, hydrogen cyanide, and oxides of nitrogen. 

Many large chemical companies produce amino resins and the raw materials needed, ie, formaldehyde, urea, and melamine. Some companies may buy raw materials to produce amino resins for use in their own products, such as plywood, chipboard, paper, textiles, or paints, and may also find it profitable to market these resins to smaller companies. The technology is highly developed and sales must be supported by adequate technical service to select the correct resin and see that it is appHed under the best conditions. 

Ammonia is used in the fibers and plastic industry as the source of nitrogen for the production of caprolactam, the monomer for nylon 6. Oxidation of propylene with ammonia gives acrylonitrile (qv), used for the manufacture of acryHc fibers, resins, and elastomers. Hexamethylenetetramine (HMTA), produced from ammonia and formaldehyde, is used in the manufacture of phenoHc thermosetting resins (see Phenolic resins). Toluene 2,4-cHisocyanate (TDI), employed in the production of polyurethane foam, indirectly consumes ammonia because nitric acid is a raw material in the TDI manufacturing process (see Amines Isocyanates). Urea, which is produced from ammonia, is used in the manufacture of urea—formaldehyde synthetic resins (see Amino resins). Melamine is produced by polymerization of dicyanodiamine and high pressure, high temperature pyrolysis of urea, both in the presence of ammonia (see Cyanamides). 

Amino Resins. Amino resins (qv) include both urea- and melamine—formaldehyde condensation products. They are thermosets prepared similarly by the reaction of the amino groups in urea [57-13-6] or melamine [108-78-1] with formaldehyde to form the corresponding methylol derivatives, which are soluble in water or ethanol. To form plywood, particle board, and other wood products for adhesive or bonding purposes, a Hquid resin is mixed with some acid catalyst and sprayed on the boards or granules, then cured and cross-linked under heat and pressure. 

Amino resins are lighter in color and have better tensile strength and hardness than phenoHc resins their impact strength and heat and water resistance are less than those of phenoHcs. The melamine—formaldehyde resins are harder and have better heat and moisture resistance than the urea resins, but they are also more expensive. The physical properties of the melamine—formaldehyde laminates are Hsted in Table 1. 

The thermoplastic or thermoset nature of the resin in the colorant—resin matrix is also important. For thermoplastics, the polymerisation reaction is completed, the materials are processed at or close to their melting points, and scrap may be reground and remolded, eg, polyethylene, propjiene, poly(vinyl chloride), acetal resins (qv), acryhcs, ABS, nylons, ceUulosics, and polystyrene (see Olefin polymers Vinyl polymers Acrylic ester polymers Polyamides Cellulose ESTERS Styrene polymers). In the case of thermoset resins, the chemical reaction is only partially complete when the colorants are added and is concluded when the resin is molded. The result is a nonmeltable cross-linked resin that caimot be reworked, eg, epoxy resins (qv), urea—formaldehyde, melamine—formaldehyde, phenoHcs, and thermoset polyesters (qv) (see Amino resins and plastics Phenolic resins). 

---