Aluminum reactivity

Nonreactive materials include glass, stainless steel, ceramic, enamel, and hard anodized aluminum. Reactive materials include (non-stainless) steel, cast-iron, copper, and aluminum. These materials conduct heat evenly and are excellent for boiling water, frying burgers, or making stock. But if you re working with acidic or alkaline ingredients, stick to nonreactive cookware. 

Tantalum is a gray, heavy, and very hard metal. When pure, it is ductile and can be drawn into fine wire, which is used as a filament for evaporating metals such as aluminum. Tantalum is almost completely immune to chemical attack at temperatures below ISOoC, and is attacked only by hydrofluoric acid, acidic solutions containing the fluoride ion, and free sulfur trioxide. Alkalis attack it only slowly. At high temperatures, tantalum becomes much more reactive. The element has a melting point exceeded only by tungsten and rhenium. Tantalum is used to make a variety... 

Carbocations usually generated from an alkyl halide and aluminum chloride attack the aromatic ring to yield alkylbenzenes The arene must be at least as reactive as a halobenzene Carbocation rearrangements can occur especially with primary alkyl hal ides... 

Partial rate factors may be used to estimate product distributions in disubstituted benzene derivatives The reactivity of a particular position in o bromotoluene for example is given by the product of the partial rate factors for the corresponding position in toluene and bromobenzene On the basis of the partial rate factor data given here for Fnedel-Crafts acylation predict the major product of the reaction of o bromotoluene with acetyl chlonde and aluminum chloride... 

In contrast to alcohols with their nch chemical reactivity ethers (compounds contain mg a C—O—C unit) undergo relatively few chemical reactions As you saw when we discussed Grignard reagents m Chapter 14 and lithium aluminum hydride reduc tions m Chapter 15 this lack of reactivity of ethers makes them valuable as solvents m a number of synthetically important transformations In the present chapter you will learn of the conditions m which an ether linkage acts as a functional group as well as the methods by which ethers are prepared... 

Common catalyst compositions contain oxides or ionic forms of platinum, nickel, copper, cobalt, or palladium which are often present as mixtures of more than one metal. Metal hydrides, such as lithium aluminum hydride [16853-85-3] or sodium borohydride [16940-66-2] can also be used to reduce aldehydes. Depending on additional functionahties that may be present in the aldehyde molecule, specialized reducing reagents such as trimethoxyalurninum hydride or alkylboranes (less reactive and more selective) may be used. Other less industrially significant reduction procedures such as the Clemmensen reduction or the modified Wolff-Kishner reduction exist as well. 

The steel (qv) iadustry is also an extremely large user of fluorspar which is added to slag to make it more reactive. Smaller amounts are also used ia the aluminum, ceramic, brick, cement, glass fiber, and foundry iadustries. 

Cationic polymerization of coal-tar fractions has been commercially achieved through the use of strong protic acids, as well as various Lewis acids. Sulfuric acid was the first polymerization catalyst (11). More recent technology has focused on the Friedel-Crafts polymerization of coal fractions to yield resins with higher softening points and better color. Typical Lewis acid catalysts used in these processes are aluminum chloride, boron trifluoride, and various boron trifluoride complexes (12). Cmde feedstocks typically contain 25—75% reactive components and may be refined prior to polymerization (eg, acid or alkali treatment) to remove sulfur and other undesired components. Table 1 illustrates the typical components found in coal-tar fractions and their corresponding properties. 

Chlorination. In some instances, the extraction of a pure metal is more easily achieved from the chloride than from the oxide. Oxide ores and concentrates react at high temperature with chlorine gas to produce volatile chlorides of the metal. This reaction can be used for common nonferrous metals, but it is particularly useful for refractory metals like titanium (see Titanium and titanium alloys) and 2irconium (see Zirconium and zirconium compounds), and for reactive metals like aluminum. 

Zinc and Zinc Alloys. Zinc metal is highly reactive in acid solutions such as sulfuric, hydrochloric, and nitric dissolving rapidly at acid concentrations normally used to pickle steel and aluminum. Dilute (1—4%) solutions of these acids can be used with caution to remove zinc oxides. 

Aluminum Paints. Mica is substituted for up to 25% of the aluminum in this type of paint (qv) as an economic measure. Mica is inert which tends to protect the more reactive aluminum from corrosive atmospheres, thus helping the paint to maintain its luster. 

The third control is by use of a fixed burnable poison. This consists of rods containing a mixture of aluminum oxide and boron carbide, included in the initial fuel loading using the vacant spaces in some of the fuel assembhes that do not have control clusters. The burnable poison is consumed during operation, causing a reactivity increase that helps counteract the drop owing to fuel consumption. It also reduces the need for excessive initial soluble boron. Other reactors use gadolinium as burnable poison, sometimes mixed with the fuel. 

Over the years, a variety of fuel types were employed. Originally, natural uranium slugs canned in aluminum were the source of plutonium, while lithium—aluminum alloy target rods provided control and a source of tritium. Later, to permit increased production of tritium, reactivity was recovered by the use of enriched uranium fuel, ranging from 5—93%. 

PhenoHcs that are not heat-reactive may be incorporated into both air-dried and baked oleoresinous coatings. AppHcations vary widely and include clear and pigmented exterior varnishes, aluminum-maintenance paints, 2inc-rich primers, can coatings, insulation varnishes, and concrete paints. As modifiers in a great variety of appHcations, they enhance the performance of oleoresinous and alkyd coatings. 

---