Adsorption, isotherms concentrations

Polymers typically exhibit a high-affinity adsorption isotherm as shown in Fig. XI-5 here the adsorbed amount increases very rapidly with bulk concentration and then becomes practically independent of concentration. 

Equation XI-27 shows that F can be viewed as related to the difference between the individual adsorption isotherms of components 1 and 2. Figure XI-9 [140] shows the composite isotherms resulting from various combinations of individual ones. Note in particular Fig. XI-9a, which shows that even in the absence of adsorption of component 1, that of component 2 must go through a maximum (due to the N[ factor in Eq. XI-27), and that in all other cases the apparent adsorption of component 2 will be negative in concentrated solution. 

Fig. XI-13. Adsorption isotherms for SNBS (sodium p-3-nonylbenzene sulfonate) (pH 4.1) and DPC (dodecyl pyridinium chloride) (pH 8.0) on mtile at approximately the same surface potential and NaCl concentration of O.OlAf showing the four regimes of surfactant adsorption behavior, from Ref. 175. [Reprinted with permission from Luuk K. Koopal, Ellen M. Lee, and Marcel R. Bohmer, J. Colloid Interface Science, 170, 85-97 (1995). Copyright Academic Press.]...

The Langmuir-Hinshelwood picture is essentially that of Fig. XVIII-14. If the process is unimolecular, the species meanders around on the surface until it receives the activation energy to go over to product(s), which then desorb. If the process is bimolecular, two species diffuse around until a reactive encounter occurs. The reaction will be diffusion controlled if it occurs on every encounter (see Ref. 211) the theory of surface diffusional encounters has been treated (see Ref. 212) the subject may also be approached by means of Monte Carlo/molecular dynamics techniques [213]. In the case of activated bimolecular reactions, however, there will in general be many encounters before the reactive one, and the rate law for the surface reaction is generally written by analogy to the mass action law for solutions. That is, for a bimolecular process, the rate is taken to be proportional to the product of the two surface concentrations. It is interesting, however, that essentially the same rate law is obtained if the adsorption is strictly localized and species react only if they happen to adsorb on adjacent sites (note Ref. 214). (The apparent rate law, that is, the rate law in terms of gas pressures, depends on the form of the adsorption isotherm, as discussed in the next section.)... 

These calculations have, as their aim, the generation of an adsorption isotherm, relating the concentration of ions in the solution to the coverage in the IHP and the potential (or more usually the charge) on the electrode. No complete calculations have been carried out incorporating all the above temrs. In general, the analytical fomi for the isothemr is... 

The hydration shell is formed with the increasing of the water content of the sample and the NA transforms from the unordered to A- and then to B form, in the case of DNA and DNA-like polynucleotides and salt concentrations similar to in vivo conditions. The reverse process, dehydration of NA, results in the reverse conformational transitions but they take place at the values of relative humidity (r.h.) less than the forward direction [12]. Thus, there is a conformational hysteresis over the hydration-dehydration loop. The adsorption isotherms of the NAs, i.e. the plots of the number of the adsorbed water molecules versus the r.h. of the sample at constant temperature, also demonstrate the hysteresis phenomena [13]. The hysteresis is i( producible and its value does not decrease for at least a week. 

A rather simpler situation arises when the bulk concentrations are sufficiently small that the adsorption isotherms approach linearity. Then (7,4), for example, shows that... 

Favorable and unfavorable equihbrium isotherms are normally defined, as in Figure 11, with respect to an increase in sorbate concentration. This is, of course, appropriate for an adsorption process, but if one is considering regeneration of a saturated column (desorption), the situation is reversed. An isotherm which is favorable for adsorption is unfavorable for desorption and vice versa. In most adsorption processes the adsorbent is selected to provide a favorable adsorption isotherm, so the adsorption step shows constant pattern behavior and proportionate pattern behavior is encountered in the desorption step. 

The 2eohte and the resin adsorbents show different adsorption isotherm characteristics, particularly at higher concentration (51). The resin adsorbent isotherm is slightly concave upward, whereas the 2eohte isotherm is linear, or even slightly concave downward. Resins, therefore, have an advantage in a UOP Sarex operation that involves high feed-soHds concentration. 

Design criteria for carbon adsorption include type and concentration of contaminant, hydrauhc loading, bed depth, and contact time. Typical ranges are 1.4—6.8 L/s/m for hydrauhc loading, 1.5—9.1 m for bed depth, and 10—50 minutes for contact time (1). The adsorption capacity for a particular compound or mixed waste stream can be deterrnined as an adsorption isotherm and pilot tested. The adsorption isotherm relates the observed effluent concentration to the amount of material adsorbed per mass of carbon. 

The water removal mechanism is adsorption, which is the mechanism for ad Class 4 drying agents. The capacity of such materials is often shown in the form of adsorption isotherms as depicted in Figures 9a and 9b. The initial adsorption mechanism at low concentrations of water is beheved to occur by monolayer coverage of water on the adsorption sites. As more water is adsorbed, successive layers are added until condensation or capidary action takes place at water saturation levels greater than about 70% relative humidity. At saturation, ad the pores are fided and the total amount of water adsorbed, expressed as a Hquid, represents the pore volume of the adsorbent. 

Adsorption of dispersants at the soHd—Hquid interface from solution is normally measured by changes in the concentration of the dispersant after adsorption has occurred, and plotted as an adsorption isotherm. A classification system of adsorption isotherms has been developed to identify the mechanisms that may be operating, such as monolayer vs multilayer adsorption, and chemisorption vs physical adsorption (8). For moderate to high mol wt polymeric dispersants, the low energy (equiUbrium) configurations of the adsorbed layer are typically about 3—30 nm thick. Normally, the adsorption is monolayer, since the thickness of the first layer significantly reduces attraction for a second layer, unless the polymer is very low mol wt or adsorbs by being nearly immiscible with the solvent. 

Adsorption. Adsorption (qv) is an effective means of lowering the concentration of dissolved organics in effluent. Activated carbon is the most widely used and effective adsorbent for dyes (4) and, it has been extensively studied in the waste treatment of the different classes of dyes, ie, acid, direct, basic, reactive, disperse, etc (5—22). Commercial activated carbon can be prepared from lignite and bituminous coal, wood, pulp mill residue, coconut shell, and blood and have a surface area ranging from 500—1400 m /g (23). The feasibiUty of adsorption on carbon for the removal of dissolved organic pollutants has been demonstrated by adsorption isotherms (24) (see Carbon, activated carbon). Several pilot-plant and commercial-scale systems using activated carbon adsorption columns have been developed (25—27). 

The major surfactant in the foam may usually be considered to be present at the bubble surfaces in the form of an adsorbed monolayer with a substantially constant F, often of the order of 3 X 10" (g mol)/ cm", for a molecular weight of several hundred. On the other hand, trace materials follow the linear-adsorption isotherm Tj = KiCj if their concentration is low enough. For a wider range of concentration a Langmuir or other type of isotherm may be applicable (Davies and Rideal, loc. cit.). 

In the first step, in which the molecules of the fluid come in contact with the adsorbent, an equihbrium is established between the adsorbed fluid and the fluid remaining in the fluid phase. Figures 25-7 through 25-9 show several experimental equihbrium adsorption isotherms for a number of components adsorbed on various adsorbents. Consider Fig. 25-7, in which the concentration of adsorbed gas on the solid is plotted against the equilibrium partial pressure p of the vapor or gas at constant temperature. At 40° C, for example, pure propane vapor at a pressure of 550 mm Hg is in equilibrium with an adsorbate concentration at point P of 0.04 lb adsorbed propane per pound of silica gel. Increasing the pressure of the propane will cause... 

Contemporary development of chromatography theory has tended to concentrate on dispersion in electro-chromatography and the treatment of column overload in preparative columns. Under overload conditions, the adsorption isotherm of the solute with respect to the stationary phase can be grossly nonlinear. One of the prime contributors in this research has been Guiochon and his co-workers, [27-30]. The form of the isotherm must be experimentally determined and, from the equilibrium data, and by the use of appropriate computer programs, it has been shown possible to calculate the theoretical profile of an overloaded peak. 

In LC, at very low concentrations of moderator in the mobile phase, the solvent distributes itself between the two phases in much the same way as the solute. However, as the dilution is not infinite, the adsorption isotherm is not linear and takes the form of the Langmuir isotherm. 

Scott and Kucera [4] carried out some experiments that were designed to confirm that the two types of solute/stationary phase interaction, sorption and displacement, did, in fact, occur in chromatographic systems. They dispersed about 10 g of silica gel in a solvent mixture made up of 0.35 %w/v of ethyl acetate in n-heptane. It is seen from the adsorption isotherms shown in Figure 8 that at an ethyl acetate concentration of 0.35%w/v more than 95% of the first layer of ethyl acetate has been formed on the silica gel. In addition, at this solvent composition, very little of the second layer was formed. Consequently, this concentration was chosen to ensure that if significant amounts of ethyl acetate were displaced by the solute, it would be derived from the first layer on the silica and not the less strongly held second layer. 

In addition, the concentration of solute in both phases increased almost linearly with the amount of solute added. This would indicate that the system was operating over that part of the adsorption isotherm that was linear. Thus, the solute was interacting... 

The adsorption process generally is of an exothermal nature. With increasing temperature and decreasing adsorbate concentration the adsorption capacity decreases. For the design of adsorption processes it is important to know the adsorption capacity at constant temperature in relation to the adsorbate concentration. Figure 11 shows the adsorption isotherms for several common solvents. 

In the low concentration limit the adsorption isotherm is alinear law as was the partition coefficient,andjustastheisothermdeviatesfromlinearityoutsideofthelowconcentration limit,sotoodoesthepartitionrelationbetweenthetwoliquidphases. 

For determining the adsorption isotherm, the equilibrium concentrations of bound and free template must be reliably measured within a large concentration interval. Since the binding sites are part of a solid, this experiment is relatively simple and can be carried out in a batch equilibrium rebinding experiment or by frontal analysis. 

---