Adhesion low molecular weight

Butadiene-Acrylonitrile Nitrile Rubber (NBR)). Acrylonitrile imparts resistance to hydrocarbon oil and gasoline. NBR finds use as an adhesive (low molecular weight), in nonlatex gloves for the health-care industry, and in automotive parts such as fuel tanks,... 

A two-component epoxy system consists of a resin and a hardener, along with possible additives such as accelerators, reactive diluents, resin modifiers, plasticizers, and fillers. Typical hardeners include aliphatic polyamines, which cure at room temperature or at slightly elevated temperatures polyamides, which provide flexibility and are widely used aromatics, which are solid and anhydrides, which require elevated temperature cure and produce thermally stable but brittle adhesives. Low molecular weight epoxies are liquid and are usually cured by amines, carboxylic acid anhydrides, and Lewis acid and base catalyst. Higher molecular weight epoxies are cured through their hydroxyl groups. Cure of epoxies involves an exothermic reaction. 

Polyurethanes. About 3% of the U.S. polyurethanes market in 1988 was derived from the condensation product of polyisocyanates with low molecular weight polyadipates having hydroxyl end groups (195). In 1986 this amounted to 29,000 t, or 4% of total adipic acid consumption. The percentage was similar in Western Europe. About 90% of these adipic acid containing polyurethanes are used in flexible or semirigid foams and elastomers, with the remainder used in adhesives, coatings, and spandex fibers. 

Hydrocarbon resin is a broad term that is usually used to describe a low molecular weight thermoplastic polymer synthesized via the thermal or catalytic polymerization of coal-tar fractions, cracked petroleum distillates, terpenes, or pure olefinic monomers. These resins are used extensively as modifiers in the hot melt and pressure sensitive adhesive industries. They are also used in numerous other appHcations such as sealants, printing inks, paints, plastics, road marking, carpet backing, flooring, and oil field appHcations. They are rarely used alone. 

Butyl mbber, a copolymer of isobutjiene with 0.5—2.5% isoprene to make vulcanization possible, is the most important commercial polymer made by cationic polymerization (see Elastomers, synthetic-butyl rubber). The polymerization is initiated by water in conjunction with AlCl and carried out at low temperature (—90 to —100° C) to prevent chain transfer that limits the molecular weight (1). Another important commercial appHcation of cationic polymerization is the manufacture of polybutenes, low molecular weight copolymers of isobutylene and a smaller amount of other butenes (1) used in adhesives, sealants, lubricants, viscosity improvers, etc. 

Phenolic resin substantially increases open time and peel strength of the formulation (80). For example, higher methylol and methylene ether contents of the resin improves peel strength and elevated temperature resistance. Adhesive properties are also influenced by the molecular weight distribution of the phenoHc low molecular weight reduces adhesion (82). 

Low molecular weight liquid nitrile rubbers with vinyl, carboxyl or mercaptan reactive end groups have been used with acrylic adhesives, epoxide resins and polyesters. Japanese workers have produced interesting butadiene-acrylonitrile alternating copolymers using Ziegler-Natta-type catalysts that are capable of some degree of ciystallisation. 

Among the different pressure sensitive adhesives, acrylates are unique because they are one of the few materials that can be synthesized to be inherently tacky. Indeed, polyvinylethers, some amorphous polyolefins, and some ethylene-vinyl acetate copolymers are the only other polymers that share this unique property. Because of the access to a wide range of commercial monomers, their relatively low cost, and their ease of polymerization, acrylates have become the dominant single component pressure sensitive adhesive materials used in the industry. Other PSAs, such as those based on natural rubber or synthetic block copolymers with rubbery midblock require compounding of the elastomer with low molecular weight additives such as tackifiers, oils, and/or plasticizers. The absence of these low molecular weight additives can have some desirable advantages, such as ... 

All grades of regular butyl rubber are tacky, rubbery and contain less unsaturation than natural rubber or styrene-butadiene rubber. On the other hand, low molecular weight grades of polyisobutylene are permanently tacky and are clear white semi-liquids, so they can be used as permanent tackifiers for cements, PSAs, hot-melt adhesives and sealants. Low molecular weight polyisobutylenes also provide softness and flexibility, and act as an adhesion promoter for difficult to adhere surfaces (e.g. polyolefins). 

Chlorinated rubber is also used to promote the adhesion of solvent-borne CR adhesives to metals and plasticized PVC. Addition of a low molecular weight chlorinated rubber (containing about 65 wt% chlorine) improves the shear strength and creep resistance of polychloroprene adhesives [75] but a reduction in open time is also produced. A heat reactivation (process in which the surface of the adhesive film is raised to 90-100°C to destroy the crystallinity of the film and allowing diffusion to produce polymer chain interlocking more rapidly) restores tack to the polychloroprene adhesives. 

Specialty waxes include polar waxes for more polar adhesive systems. Examples would be castor wax (triglyceride of 12-hydroxy stearic acid) or Paracin wax N- 2 hydroxy ethyl)-12-hydroxy stearamide) which are used in polyester, polyamide, or with high VA EVA copolymer-based systems. Other common polar waxes are maleated polyethylenes, which are used to improve the specific adhesion of polyethylene-based adhesives, and low molecular weight ethylene copolymers with vinyl acetate or acrylic acid, which are used to improve low temperature adhesion. High melting point isotactic polypropylene wax (7 155°C) and highly refined paraffin wax (7,n 83°C) are used where maximum heat resistance is critical. Needless to say, these specialty waxes also command a premium price, ranging from 2 to 5 times that of conventional paraffin wax. 

For hot melt adhesives there are other considerations as well in choosing an antioxidant. Primary among these are volatility and solubility. Low molecular weight antioxidants (MW <400) should be avoided, for example BHT, as these... 

This difference in reactivity between the different classes of amines explains the difference in the primer performance on polyolefin substrates with ethyl cyanoacrylate-based adhesives [37J. Since primary and secondary amines form low molecular weight species, a weak boundary layer would form first, instead of high molecular weight polymer. Also, the polymer, which does ultimately form, has a lower molecular weight, which would lower adhesives strength [8,9]. 

---