Activity coefficient equations Wilson

A model is needed to calculate liquid-liquid equilibrium for the activity coefficient from Equation 4.67. Both the NRTL and UNIQUAC equations can be used to predict liquid-liquid equilibrium. Note that the Wilson equation is not applicable to liquid-liquid equilibrium and, therefore, also not applicable to vapor-liquid-liquid equilibrium. Parameters from the NRTL and UNIQUAC equations can be correlated from vapor-liquid equilibrium data6 or liquid-liquid equilibrium data9,10. The UNIFAC method can be used to predict liquid-liquid equilibrium from the molecular structures of the components in the mixture3. 

Calculate Wilson parameters from the infinite-dilution activity coefficients. The equations are lnyj00 = 2.441 = —lnGii2 + 1 — G2,i, and Inyf° = 1.711 = —lnG2ii + 1 — Gji2. Solving by trial and error, Gij2 = 0.1555 and G2,i = 0.4209. 

Eq. (2.7-5a) is called the VSM-W as it uses the Wilson equation for the activity coefficient. This equation has been used successfully to describe adsorption of many hydrocarbons on activated carbon. 

Haeany Solution Model The initial model (37) considered the adsorbed phase to be a mixture of adsorbed molecules and vacancies (a vacancy solution) and assumed that nonideaUties of the solution can be described by the two-parameter Wilson activity coefficient equation. Subsequendy, it was found that the use of the three-parameter Flory-Huggins activity coefficient equation provided improved prediction of binary isotherms (38). 

The activity coefficient (y) based corrector is calculated using any applicable activity correlating equation such as the van Laar (slightly polar) or Wilson (more polar) equations. The average absolute error is 20 percent. 

Outlined below are the steps required for of a X T.E calciilation of vapor-phase composition and pressure, given the liquid-phase composition and temperature. A choice must be made of an equation of state. Only the Soave/Redlich/Kwong and Peng/Robinson equations, as represented by Eqs. (4-230) and (4-231), are considered here. These two equations usually give comparable results. A choice must also be made of a two-parameter correlating expression to represent the liquid-phase composition dependence of for each pq binaiy. The Wilson, NRTL (with a fixed), and UNIQUAC equations are of general applicabihty for binary systems, the Margules and van Laar equations may also be used. The equation selected depends on evidence of its suitability to the particular system treated. Reasonable estimates of the parameters in the equation must also be known at the temperature of interest. These parameters are directly related to infinite-dilution values of the activity coefficients for each pq binaiy. 

Table 13-1, based on the binary-system activity-coefficient-eqnation forms given in Table 13-3. Consistent Antoine vapor-pressure constants and liquid molar volumes are listed in Table 13-4. The Wilson equation is particularly useful for systems that are highly nonideal but do not undergo phase splitting, as exemplified by the ethanol-hexane system, whose activity coefficients are snown in Fig. 13-20. For systems such as this, in which activity coefficients in dilute regions may...

Wilson s [77] equation has been found to be quite accurate in predicting the vapor-liquid relationships and activity coefficients for miscible liquid systems. The results can be expanded to as many components in a multicomponent system as may be needed without any additional data other than for a binary system. This makes Wilson s and... 

Blanco et al. have also correlated the results with the van Laar, Wilson, NRTL and UNIQUAC activity coefficient models and found all of them able to describe the observed phase behavior. The value of the parameter ai2 in the NRTL model was set equal to 0.3. The estimated parameters were reported in Table 10 of the above reference. Using the data of Table 15.7 estimate the binary parameters in the Wislon, NRTL and UNIQUAC models. The objective function to be minimized is given by Equation 15.11. 

Using the Wilson equation, calculate the activity coefficients for isopropyl alcohol (IPA) and water in a mixture of IPA, methanol, water, and ethanol composition, all mol fraction ... 

The values of the activity coefficients determined at the azeotropic composition can be used to calculate the coefficients in the Wilson equation (or any other of the three-suffix equations) and the equation used to estimate the activity coefficients at other compositions. Horsley (1973) gives an extensive collection of data on azeotropes. 

The constants in any of the activity coefficient equations can be readily calculated from experimental values of the activity coefficients at infinite dilution. For the Wilson equation ... 

Thus, if the saturated vapor pressure is known at the azeotropic composition, the activity coefficient can be calculated. If the composition of the azeotrope is known, then the compositions and activity of the coefficients at the azeotrope can be substituted into the Wilson equation to determine the interaction parameters. For the 2-propanol-water system, the azeotropic composition of 2-propanol can be assumed to be at a mole fraction of 0.69 and temperature of 353.4 K at 1 atm. By combining Equation 4.93 with the Wilson equation for a binary system, set up two simultaneous equations and solve Au and A21. Vapor pressure data can be taken from Table 4.11 and the universal gas constant can be taken to be 8.3145 kJ-kmol 1-K 1. Then, using the values of molar volume in Table 4.12, calculate the interaction parameters for the Wilson equation and compare with the values in Table 4.12. 

The most important aspect of the simulation is that the thermodynamic data of the chemicals be modeled correctly. It is necessary to decide what equation of state to use for the vapor phase (ideal gas, Redlich-Kwong-Soave, Peng-Robinson, etc.) and what model to use for liquid activity coefficients [ideal solutions, solubility parameters, Wilson equation, nonrandom two liquid (NRTL), UNIFAC, etc.]. See Sec. 4, Thermodynamics. It is necessary to consider mixtures of chemicals, and the interaction parameters must be predictable. The best case is to determine them from data, and the next-best case is to use correlations based on the molecular weight, structure, and normal boiling point. To validate the model, the computer results of vapor-liquid equilibria could be checked against experimental data to ensure their validity before the data are used in more complicated computer calculations. 

The methods most generally used for the calculation of activity coefficients at intermediate pressures are the Wilson (1964) and UNIQUAC (Abrams and Prausnitz, 1975) equations. Wilson s equation was used by Sato et al. (1985) to predict the composition of fhe condensate gas stripped from a packed bed fermenter at 30°C, whilst Beck and Bauer (1989) used the UNIQUAC equation, with temperature-dependent parameters given by Kolbe and Gmehling (1985), for their model of an anaerobic gas-solid fluidized bed fermenter at 36°C. In this case it was necessary to go beyond the temperature range of fhe source data down to 16°C in order to predict the composition of the fluidizing gas leaving the condenser. 

In many studies of the SLE of ILs, three methods have been used to derive the solute activity coefficients, pj, from the so-called correlation equations that describe the Gibbs free energy of mixing (GE), fhe Wilson [103], UNIQUAC ASM [104], and NRTLl [105] models. Historically, fhe UNIQUAC... 

The following three equations were used for the correlation of the activity coefficient to solution composition. The Wilson (11) equation ... 

An alternative approach is to estimate activity coefficients of the solvents from experimental data and correlate these coefficients using, for example, the Wilson equation. Rousseau et al. (3) and Jaques and Furter (4) have used the Wilson equation, as well as other integrated forms of the Gibbs-Duhem equation, to show the utility of this approach. These authors found it necessary, however, to modify the definitions of the solvent reference states so that the results could be normalized. 

In this study, a thermodynamic framework has been presented for the calculation of vapor-liquid equilibria for binary solvents containing nonvolatile salts. From an appropriate definition of a pseudobinary system, infinite dilution activity coefficients for the salt-containing system may be estimated from a knowledge of vapor pressure lowering, salt-free infinite dilution activity coefficients, and a single system-dependent constant. Parameters for the Wilson equation may be determined from the infinite dilution activity coefficients. 

Values of the activity coefficients are deduced from experimental data of vapor-liquid equilibria and correlated or extended by any one of several available equations. Values also may be calculated approximately from structural group contributions by methods called UNIFAC and ASOG. For more than two components, the correlating equations favored nowadays are the Wilson, the NRTL, and UNIQUAC, and for some applications a solubility parameter method. The fust and last of these are given in Table 13.2. Calculations from measured equilibrium compositions are made with the rearranged equation... 

TABLE 13.2. Activity Coefficients from Solubility Parameters and from the Wilson Equation... 

Measurements of binary vapor-liquid equilibria can be expressed in terms of activity coefficients, and then correlated by the Wilson or other suitable equation. Data on all possible pairs of components can be combined to represent the vapor-liquid behavior of the complete mixture. For exploratory purposes, several rapid experimental techniques are applicable. For example, differential ebulliometry can obtain data for several systems in one laboratory day, from which infinite dilution activity coefficients can be calculated and then used to evaluate the parameters of correlating equations. Chromatography also is a well-developed rapid technique for vapor-liquid equilibrium measurement of extractive distillation systems. The low-boiling solvent is deposited on an inert carrier to serve as the adsorbent. The mathematics is known from which the relative volatility of a pair of substances can be calculated from the effluent trace of the elutriated stream. Some of the literature of these two techniques is cited by Walas (1985, pp. 216-217). 

The boiling point of THF at 5 atm (404.2 K) is chosen as the reference temperature. The liquid phase activity coefficients were calculated using the Wilson equation... 

Modern theoretical developments in the molecular thermodynamics of liquid-solution behavior are based on the concept of local composition. Within a liquid solution, local compositions, different from the overall mixture composition, are presumed to account for the short-range order and nonrandom molecular orientations that result from differences in molecular size and intermolecular forces. The concept was introduced by G. M. Wilson in 1964 with the publication of a model of solution behavior since known as the Wilson equation. The success of this equation in the correlation of VLE data prompted the development of alternative local-composition models, most notably the NRTL (Non-Random-Two Liquid) equation of Renon and Prausnitz and the UNIQUAC (UNIversal QUAsi-Chemical) equation of Abrams and Prausnitz. A further significant development, based on the UNIQUAC equation, is the UNIFAC method,tt in which activity coefficients are calculated from contributions of the various groups making up the molecules of a solution. 

Application of the Wilson equation for evaluation of activity coefficients requires knowledge of the liquid-phase composition. We therefore calculate x, by Eq. (12.27) ... 

In these equations, y, and y2 are activity coefficients of components 1 and 2, respectively, GE is Gibbs molar excess free energy, A, 2 and A2j, are Van Laar parameters, G, 2 and G2j, are Wilson parameters, that is,... 

Related Calculations. These calculations show how to use vapor-liquid equilibrium data to obtain parameters for activity-coefficient correlations such as those of Van Laar and Wilson. (Use of liquid-liquid equilibrium data for the same purpose is shown in Example 1.20.) If the system forms an azeotrope, the parameters can be obtained from a single measurement of the azeotropic pressure and the composition of the constant boiling mixture. If the activity coefficients at infinite dilution are available, the two parameters for the Van Laar equation are given directly, and the two in the case of the Wilson equation can be solved for as shown in the example. 

ESTIMATING THE PARAMETERS FOR THE WILSON-EQUATION MODEL FOR ACTIVITY COEFFICIENTS 3.11... 

Calculate the activity coefficients of chloroform and acetone at 0°C in a solution containing 50 mol % of each component, using the Wilson-equation model. The Wilson constants for the system (with subscript 1 pertaining to chloroform and subscript 2 to acetone) are... 

---