Vapor phase catalysts development

II. Brief History of Vapor-Phase-Catalyst Development. 242... 

Phenol can also be prepared by the decomposition of benzoic acid prepared by the oxidation of toluene.927,978 The process is an oxidative decarboxylation catalyzed by copper(II). An interesting feature of this reaction is that the phenolic hydroxyl group enters into the position ortho to the carboxyl group as was proved by 14C labeling.979 In the Dow process980 molten benzoic acid is transformed with steam and air in the presence of Cu(II) and Mg(II) salts at 230-240°C. A copper oxide catalyst is used in a vapor-phase oxidation developed by Lummus.981... 

In 1987, Toray Industries, Inc., announced the development of a new process for making aromatic nitriles which reportedly halved the production cost, reduced waste treatment requirements, and reduced production time by more than two-thirds, compared with the vapor-phase process used by most producers. The process iavolves the reaction of ben2oic acid (or substituted ben2oic acid) with urea at 220—240°C ia the presence of a metallic catalyst (78). 

Acetylation of acetaldehyde to ethyUdene diacetate [542-10-9], a precursor of vinyl acetate, has long been known (7), but the condensation of formaldehyde [50-00-0] and acetic acid vapors to furnish acryflc acid [97-10-7] is more recent (30). These reactions consume relatively more energy than other routes for manufacturing vinyl acetate or acryflc acid, and thus are not likely to be further developed. Vapor-phase methanol—methyl acetate oxidation using simultaneous condensation to yield methyl acrylate is still being developed (28). A vanadium—titania phosphate catalyst is employed in that process. 

The Reaction. Acrolein has been produced commercially since 1938. The first commercial processes were based on the vapor-phase condensation of acetaldehyde and formaldehyde (1). In the 1940s a series of catalyst developments based on cuprous oxide and cupric selenites led to a vapor-phase propylene oxidation route to acrolein (7,8). In 1959 Shell was the first to commercialize this propylene oxidation to acrolein process. These early propylene oxidation catalysts were capable of only low per pass propylene conversions (ca 15%) and therefore required significant recycle of unreacted propylene (9—11). 

Dehydrogenation of Propionates. Oxidative dehydrogenation of propionates to acrylates employing vapor-phase reactions at high temperatures (400—700°C) and short contact times is possible. Although selective catalysts for the oxidative dehydrogenation of isobutyric acid to methacrylic acid have been developed in recent years (see Methacrylic ACID AND DERIVATIVES) and a route to methacrylic acid from propylene to isobutyric acid is under pilot-plant development in Europe, this route to acrylates is not presentiy of commercial interest because of the combination of low selectivity, high raw material costs, and purification difficulties. 

Manufacture and Processing. Until World War II, phthaUc acid and, later, phthaUc anhydride, were manufactured primarily by Hquid-phase oxidation of suitable feedstocks. The favored method was BASF s oxidation of naphthalene [91-20-3] by sulfuric acid ia the presence of mercury salts to form the anhydride. This process was patented ia 1896. During World War I, a process to make phthaUc anhydride by the oxidation of naphthalene ia the vapor phase over a vanadium and molybdenum oxide catalyst was developed ia the United States (5). Essentially the same process was developed iadependendy ia Germany, with U.S. patents being granted ia 1930 and 1934 (6,7). 

The Tatoray process, which was developed by Toray Industries, Inc., and is available for Hcense through UOP, can be appHed to the production of xylenes and benzene from feedstock that consists typically of toluene [108-88-3] either alone or blended with aromatics (particularly trimethylbenzenes and ethyl-toluenes). The main reactions are transalkylation (or disproportionation) of toluene to xylene and benzene or of toluene and trimethylbenzenes to xylenes in the vapor phase over a highly selective fixed-bed catalyst in a hydrogen atmosphere at 350—500°C and 1—5 MPa (10—50 atm). Ethyl groups are... 

A vapor-phase process primarily for ECC off-gas feeds was developed by Sinopec Technology Company based on a 2eoHte catalyst of the Pentasd type (24,25). It reHes on frequent regeneration of the catalyst to minimi2e pretreatment of the ECC off-gas and allows the impurities in the feed gas to react with ben2ene to form by-products. Consequently, the product yield and purity are low. Joint licensing by ABB Lummus Crest and Sinopec was announced in 1994. 

In oxychlorination, ethylene reacts with dry HCl and either air or pure oxygen to produce EDC and water. Various commercial oxychlorination processes differ from one another to some extent because they were developed independentiy by several different vinyl chloride producers (78,83), but in each case the reaction is carried out in the vapor phase in either a fixed- or fluidized-bed reactor containing a modified Deacon catalyst. Unlike the Deacon process for chlorine production, oxychlorination of ethylene occurs readily at temperatures weU below those requited for HCl oxidation. 

Dutch State Mines (Stamicarbon). Vapor-phase, catalytic hydrogenation of phenol to cyclohexanone over palladium on alumina, Hcensed by Stamicarbon, the engineering subsidiary of DSM, gives a 95% yield at high conversion plus an additional 3% by dehydrogenation of coproduct cyclohexanol over a copper catalyst. Cyclohexane oxidation, an alternative route to cyclohexanone, is used in the United States and in Asia by DSM. A cyclohexane vapor-cloud explosion occurred in 1975 at a co-owned DSM plant in Flixborough, UK (12) the plant was rebuilt but later closed. In addition to the conventional Raschig process for hydroxylamine, DSM has developed a hydroxylamine phosphate—oxime (HPO) process for cyclohexanone oxime no by-product ammonium sulfate is produced. Catalytic ammonia oxidation is followed by absorption of NO in a buffered aqueous phosphoric acid... 

A process for the production of ethylenimine [151 -56-4] a suspect carcinogen, by the vapor phase dehydration of monoethanol amine has been developed (128—132). By using an alkyleneamine co-feed with the alkan olamine, higher alkylene amines are made in situ (133). The catalysts are tungsten-, niobium-, or phosphate-based. 

Hydrar A catalytic process for hydrogenating benzene to cyclohexane. It is conducted in the vapor phase with a fixed-bed reactor. The catalysts are based on platinum and modified by lithium an alternative nickel-based catalyst is also used. Developed by UOP, subsequently renamed HB Unibon. 

Iso-Kel [Isomerization-Kellogg] A fixed-bed, vapor-phase isomerization process for making high-octane gasoline from aliphatic petroleum fractions. The catalyst is platinum on alumina. Developed by MW Kellogg. 

Tatoray [Transalkylation aromatics Toray] A process for transalkylating toluene, and/or trimethylbenzenes, into a mixture of benzene and xylenes. Operated in the vapor phase, with hydrogen, in a fixed bed containing a zeolite catalyst. Developed jointly by Toray Industries and UOP and now licensed by UOP. First operated commercially in Japan in 1969 as of 1992, 23 units were operating and 6 more were in design and construction. 

Xyloflning [Xylol refining] A process for isomerizing a petrochemical feedstock containing ethylbenzene and xylenes. The xylenes are mostly converted to the equilibrium mixture of xylenes the ethylbenzene is dealkylated to benzene and ethylene. This is a catalytic, vapor-phase process, operated at approximately 360°C. The catalyst (Encilite-1) is a ZSM-5-type zeolite in which some of the aluminum has been replaced by iron. The catalyst was developed in India in 1981, jointly by the National Chemical Laboratory and Associated Cement Companies. The process was piloted by Indian Petrochemicals Corporation in 1985 and commercialized by that company at Baroda in 1991. 

I PA could always be made by direct hydration, but the severe operating conditions (high pressures and temperatures) and puny yields had always limited the economic enthusiasm for the process. Then catalysis research paid off with the development of a sulfonated polystyrene cationic exchange resin catalyst, a mouthful in itself. The breakthrough permitted reduced pressures and temperatures without loss of yield. The catalyst works in the vapor phase, the liquid phase, and the mixed phase. 

Carbonylation of methanol to form acetic acid has been performed industrially using carbonyl complexes of cobalt ( ) or rhodium (2 ) and iodide promoter in the liquid phase. Recently, it has been claimed that nickel carbonyl or other nickel compounds are effective catalysts for the reaction at pressure as low as 30 atm (2/4), For the rhodium catalyst, the conditions are fairly mild (175 C and 28 atm) and the product selectivity is excellent (99% based on methanol). However, the process has the disadvantages that the proven reserves of rhodium are quite limited in both location and quantity and that the reaction medium is highly corrosive. It is highly desirable, therefore, to develop a vapor phase process, which is free from the corrosion problem, utilizing a base metal catalyst. The authors have already reported that nickel on activated carbon exhibits excellent catalytic activity for the carbonylation of... 

In 1986, a process to produce 1 by the continuous, vapor phase oxidation of 1,3-butadiene over a silver on alumina catalyst was discovered by Monnier and Muehlbauer of the Kodak Corporate Research Laboratories (10). The process was further developed and commercialized by Eastman Chemical Company at its Longview, Texas plant (11). Following this discovery of an economical process for 1, the production of 2,5-DHF was once again of commercial interest. 

There has been an enormous technological interest in tertfa/j-butanol (tBA) dehydration during the past thirty years, first as a primary route to methyl te/f-butyl ether (MTBE) (1) and more recently for the production of isooctane and polyisobutylene (2). A number of commercializable processes have been developed for isobutylene manufacture (eq 1) in both the USA and Japan (3,4). These processes typically involve either vapor-phase tBA dehydration over a silica-alumina catalyst at 260-370°C, or liquid-phase processing utilizing either homogenous (sulfonic acid), or solid acid catalysis (e.g. acidic cationic resins). More recently, tBA dehydration has been examined using silica-supported heteropoly acids (5), montmorillonite clays (6), titanosilicates (7), as well as the use of compressed liquid water (8). 

---