Urea-thiourea-formaldehyde resins

Decorative laminates have a core or base of Kraft paper impregnated with a phenolic resin. A printed pattern layer impregnated with a melamine-formaldehyde or urea-thiourea-formaldehyde resin is then laid on the core and on top of this a melamine resin-impregnated protective translucent outer sheet. The assembly is then cured at 125-150°C in multi-daylight presses in the usual way. 

FlameGard PE Cone. Is recommended for use on 100% polyester FlameGard 908 is a thermosetting urea/thiourea formaldehyde resin type flame retardant producing a soft to moderate firm hand. 

Butylpherrol formaldehyde resirr Urea-thiourea-formaldehyde resin Poly(virrylrraphthalerre)... 

Resins may influence phototendering of rayons. Wood (26) has reported that viscose rayon fabrics treated with urea formaldehyde or thiourea formaldehyde resin are protected from the degradative effects of mercury vapor lamp radiation. The mechanism of the protective effect is not fully understood as yet. Possibly resins can quench free radicals formed during irradiation. Work with resin-treated cotton indicates that simultaneous scission of cellulose chain molecules and resin-cellulose bonds occurs on exposure to light (63). 

Thiourea closely resembles urea in that reaction with formaldehyde gives methylol derivatives and then resinous condensates which on continued heating yield network structures. Thiourea-formaldehyde resins are slower curing than urea-formaldehyde resins and the hardened products are more brittle and more water-resistant. At one time thiourea-formaldehyde resins were added to urea-formaldehyde resins to give mouldings and laminates with improved water-resistance. These mixed resins have now been largely superseded by melamine-formaldehyde resins which give products with better resistance to heat. 

Depending on the type of amine component, amino plastics are divided into urea-formaldehyde (UF), melamine-formaldehyde (MF), aniline-formaldehyde, and thiourea-formaldehyde resins. Melamine-formaldehyde resins are the most resistant to chemicals. 

The term aminoplastics has been coined to cover a range of resinous polymers produced by interaction of amines or amides with aldehydes. Of the various polymers of this type that have been produced there are two of current commercial importance in the field of plastics, the urea-formaldehyde and the melamine-formaldehyde resins. There has in the past also been some commercial interest in aniline-formaldehyde resins and in systems containing thiourea but today these are of little or no importance. Melamine-phenol-formaldehyde resins have also been introduced for use in moulding powders, and benzoguanamine-based resins are used for surface coating applications. 

Thiourea will react with neutralised formalin at 20-30°C to form methylol derivatives which are slowly deposited from solution. Heating of methylol thiourea aqueous solutions at about 60°C will cause the formation of resins, the reaction being accelerated by acidic conditions. As the resin average molecular weight increases with further reaction the resin becomes hydrophobic and separates from the aqueous phase on cooling. Further reaction leads to separation at reaction temperatures, in contrast to urea-formaldehyde resins, which can form homogeneous transparent gels in aqueous dispersion. 

At one time thiourea-urea-formaldehyde resins were of importance for moulding powders and laminating resins because of their improved water resistance. They have now been almost completely superseded by melamine-formaldehyde resins with their superior water resistance. It is, however, understood that a small amount of thiourea-containing resin is still used in the manufacture of decorative laminates. 

PS—polystyrene UF—urea-formaldehyde resin glut—glutaraldehyde thio— thiourea BSA—bovine serum albumin PHEMA—poly(hydroxyethyl methacrylate) IDA—iminodiacetic acid LDH—lactate dehydrogenase OPS—o-phosphoserine 8HQ—8-hydroxyquinoUne Bpa— bis(2-pyridyl-methyl) amine. 

The first commercially successful synthetic polymer was phenol-formaldehyde (PF) [Smith, 1899]. The resin was introduced in 1909 by Baekeland as Bakelite . The urea-formaldehyde resins (UF), were discovered in 1884, but production of Beetle moldable resin commenced in 1928. Three years later, Formica , phenolic paper covered with decorative layer protected by UF, was introduced. The thiourea-formaldehyde molding powders were commercialized in 1920, while in 1935, Ciba introduced Cibanite , anihne-formaldehyde (AF) molding materials, then two years later, the melamine-formaldehyde (MF). 

Phenol-formaldehyde pure resin Ester gum modified phenol-formaldehyde Urea formaldehyde Thiourea formaldehyde Coumarone-indene. . 

The flammability of polyamide fibres is usually reduced in the finishing process. Rigid yams are dressed by applying urea, thiourea, or melamine/formaldehyde resins. On the surface of flexible polyamide fibres, about 10 per cent of ammonium bromide is fixed by a urea/formaldehyde resin. Specific flame-retardant finishing is not usual. ... 

Phenol-formaldehyde was reported as the first commercially synthetic polymer (1899) which was introduced as BakeliteT by Baekeland in 1909. This was the period which marked the dawn for the production of commercial synthetic thermosetting polymers. Other advances in the field included the discovery of urea-formaldehyde resins in 1884 and the beginning of their commercialization as Beetle moldable resin in 1928, followed by thiourea-formaldehyde (1920), aniline-formaldehyde (Cibatine by Ciba, 1935) and melamine-formaldehyde (1937) moulding powders. The year 1909 marked the discovery of epoxy compounds by Prileschaiev, which were not used until World War 2. The first thermoset polyesters, invented by Ellis, date back to 1934 and in 1938 was reported their first use in the forms of glass-reinforced materials [1]. 

Amine resin n. Synthetic resin derived from the reaction of urea, thiourea, melamine or allied compounds with aldehydes, particularly formaldehyde. 

---