Triethylamine carbonate

Mundry (1965) has also described the use of DEAE-Sephadex for the separation of ribonucleotides and nucleosides. Using a 1.1 x85 cm column and a 1.1-1 linear gradient from 0.04 M Tris-HCl pH 8.8 to 0.20 M Tris-HCl, 0.25 M NaCl pH 9.5 or a linear gradient from 0.04 M triethylamine carbonate pH 8.8 to 0.35 M triethylamine carbonate, 0.15 M NaCl pH 9.5 he has separated the 8 main ribonucleosides and nucleotides. The nucleoside separation is very sensitive to traces of salt and some difficulty with reproducibility was experienced. 

The a-carbon atom of the phenylacetyl group is more susceptible to attack by the basic catalyst (triethylamine) than the acetyl group hence a-phenyl-cinnamic acid, but no cinnamic acid, is obtained. 

Alternatively, use the following procedure in which triethylamine replaces potassium acetate as the basic catalyst. Place 2 1 g. (2-0 ml.) of purified benzaldehyde, 2 0 ml. of anhydrous triethylamine and 5 0 ml. of A.R. acetic anhydride in a 200 ml. round-bottomed flask, equipped with a short reflux condenser and a calcium chloride drying tube. Boil the solution gently for 24 hours—heating may be interrupted. Incorporate a steam distillation apparatus in the flask and steam distil until the distillate is no longer cloudy (about 100 ml.) and then collect a further 50 ml. of the distillate di ard the steam distillate. Transfer the residue in the flask to a 400 ml. beaker, add water until the vplume is about 200 ml., then 0 2 g. of decolourising carbon, and boil for a few minutes. Filter the hot solution, and acidify the hot filtrate with 1 1 hydrochlorioiaoid... 

A cousin to this reduction is one using stannous chloride (a.k.a. SnCb, a.k.a. Tin chloride) which is done exactly as the calcium one except that about lOOg of SnCb is used in place of the Mg or Ca and the addition occurs at room temperature and the solution is stirred for one hour rather than 15 minutes. Some very good reductions that operate almost exclusively at room temperature with no pressure and give almost 100% yields are to follow. The only reason Strike did not detail these methods is that some of the chemicals involved are a little less common than Strike is used to but all are available to the public. These alternatives include acetlylacetone and triethylamine [73], propanedithlol and trieth-ylamine [74], triphenylphosphine [75], NaBH4 with phase transfer catalyst [76], H2S and pyridine [77], and palladium hydrox-ide/carbon with hydrazine [78], stannous chloride dihydrate [85]. 

To illustrate the specific operations involved, the scheme below shows the first steps and the final detachment reaction of a peptide synthesis starting from the carboxyl terminal. N-Boc-glycine is attached to chloromethylated styrene-divinylbenzene copolymer resin. This polymer swells in organic solvents but is completely insoluble. ) Treatment with HCl in acetic acid removes the fert-butoxycarbonyl (Boc) group as isobutene and carbon dioxide. The resulting amine hydrochloride is neutralized with triethylamine in DMF. 

Phosphorothioates. All three synthetic approaches appHcable to unmodified oligonucleotides can be adapted for synthesis of phosphorothioates (11) (33,46). If all of the phosphodiester linkages in an oligonucleotide are to be replaced with phosphorothioates, the ff-phosphonate method for coupling, followed by oxidation with Sg in carbon disulfide and triethylamine in the final step, is the most straightforward method. 

Benzyl chloride undergoes self-condensation relatively easily at high temperatures or in the presence of trace metallic impurities. The risk of decomposition during distillation is reduced by the use of various additives including lactams (43) and amines (44,45). Lime, sodium carbonate, and triethylamine are used as stabilizers during storage and shipment. Other soluble organic compounds that are reported to function as stabilizers in low concentration include DMF (46), arylamines (47), and triphenylphosphine (48). 

A. l-THmethyleilyloxyayalopentsne. A 1-L, two-necked, round-bottomed flask is equipped with a mechanical stirrer and a reflux condenser having a drying tube (calcium chloride). The flask is charged with 200 mL of dimethylformamide (Note 1), 45 g (0.54 mol) of cyclopentanone (Note 2), 65.5 g (0.6 mol) of chlorotrimethylsilane (Note 2) and 185 mL (1.33 mol) of triethylamine (Note 1), and the mixture is refluxed for 17 hr (Note 3). The mixture is cooled, diluted with 350 mL of pentane, and washed four times with 200-mL portions of cold saturated aqueous sodium hydrogen carbonate. The... 

The submitters report that both l,4-diazabicyclo[2.2.2]octane and triethylamine have been used to catalyze this decomposition. Tri-ethylamine was less satisfactory as a catalyst because of its relatively rapid reaction with the solvent, carbon tetrachloride, to form triethylamine hydrochloride and because of difficulty encountered in separating triethylamine from the dicarbonate pi oduct. The 1,4-diazabicyclo-[2.2.2]octane was efficiently separated from the dicarbonate product by the procedure described in which the crude product was washed with very dilute aqueous acid. 

In contrast to phosphorus esters, sulfur esters are usually cleaved at the carbon-oxygen bond with carbon-fluorine bond formation Cleavage of esteri nf methanesulfonic acid, p-toluenesidfonic acid, and especially trifluoromethane-sulfonic acid (tnflic acid) by fluoride ion is the most widely used method for the conversion of hydroxy compounds to fluoro derivatives Potassium fluoride, triethylamine trihydrofluoride, and tetrabutylammonium fluoride are common sources of the fluoride ion For the cleavage of a variety of alkyl mesylates and tosylates with potassium fluoride, polyethylene glycol 400 is a solvent of choice, the yields are limited by solvolysis of the leaving group by the solvent, but this phenomenon is controlled by bulky substituents, either in the sulfonic acid part or in the alcohol part of the ester [42] (equation 29)... 

Figure 3-14 shows an induction period in the reaction of carbon suboxide (O=C=C=C=0) with triethylamine. This reaction is complex and is not yet... 

Figure 3-14. Absorbance-time plots for the reaction of carbon suboxide and triethylamine in ether solution in the presence of acetic anhydride. The initial C3O2 concentration was 2.03 X I0 - M the amine concentrations were 3 X lO " M, 5 x 10 M, and 7 X lO " M.

Acylation with aromatic acid chlorides was believed to occur on carbon 91). The dibenzoylation of the enamine (113) with benzoyl chloride in the presence of triethylamine has, however, been shown to give a mixture of three products (92). The major components are the cis and Irons isomers of the O-acylated enamino ketone (Ola and b) and the minor isomer is the 2,6-diacylated enamine (132). 

Conjugated dienamines were found to give predominantly double four-membered-ring adducts as well as a small amount of the six-membered-ring adduct (466,468). This important result indicates preferred attack at the terminal carbon of the dienamine system (in contrast to alkylation, for instance) in the generation of an initial zwitterionic intermediate. Addition of sulfonyl chloride and triethylamine to a homocyclic dienamine gave only the bridged product (446). 

To a solution of 112 (2.0 g, 43.0 mmol) in 50 mL of dry THF at -65°C was added a solution of 111 (4.45 g, 34.0 mmol) in 100 mL of absolute ethanol containing 5 mL of acetic acid cooled to - 65°C in one portion. After stirring for 15 min., dry triethylamine (4.8 g, 510 mmol) was added. The reaction continued for 24 h with slow warming to room temperature before reducing the volume to 10 mL. The crude 113 was brought to pH 10 with potassium carbonate. The aqueous solution was continuously extracted with chloroform, dried (K2CO3), evaporated onto neutral alumina, placed on a column of neutral alumina (50 g) and eluted with chloroform. The solvent was evaporated and the residue crystallized from ethanol to yield 113 (2.86 g 55%). The yellow solid had a mp = 72.5-73.8°C. 

The reaction of tertiary alkylthioenyne alcohols (205) with carbon dioxide [70-73 atm, 70-75°C, Cu(I) salts, triethylamine] leads to 4,4-dimethyl-5-(alkyl-thioethenylmethylene)-l,3-dioxolan-2-ones (206) (79KGS1617 79ZOR1319). 

A 15.7 g (0.1 mol) of 2,6-dihydroxy methylpy rid in e hydrochloride are suspended in 176 ml of acetonitrile, and 20fi ml (0.15 mol) of triethylamine are added to the suspension. Thereafter 13 ml (0.22 mol) of methyl isocyanate are added dropwise to the reaction mixture at 20°C to 25°C. The reaction mixture is stirred at 20°C to 30°C for one hour, thereafter boiled for 3 hours, and finally the solvent is evaporated under reduced pressure. 35 to 40 g of a greyish, crystalline residue are obtained, which Is a mixture of 2,6-dihydroxymethylpyridine-bis-(N-methylcarbamate) and triethylamine hydrochloride. The obtained residue is dissolved in 80 ml of hot water, decolorized with 2 g of activated carbon when hot, and filtered after 30 minutes of stirring. The filtrate is cooled, the resulting crystal suspension is stirred at 0°C to 5°C for 3 hours, the solids are filtered off, and dried at 50°C to 60°C. 

---