Trends response

Economic Aspects. The 1992 MEK nameplate capacity for the United States, East Asia, and Western Europe is Hsted in Table 5. During the period 1980—1989 MEK achieved a negative growth rate as demand dropped from 311,000 (48) to 228, 000 t/yr (49). Stricter VOC regulations were largely responsible for the decline, and the trend will continue as solvent recovery and recycling, as well as substitution away from MEK, take effect. 

In 1965 the Water Quahty Act established a new trend in water pollution control. It provided that the states set water quality standards in accordance with federal guidelines. If the states f ed to do so, the standards would be set by the federal government subject to a review hearing. In 1966, the Clean Water Restoration Act transferred the Feder Water Pollution Control Administration from the Department of Health, Education and Welfare to the Department of the Interior. It also gave the Interior Department the responsibility for the Oil Pollution Act. 

Although motors and controllers can be bought separately, the trend is to purchase a system from a given manufacturer. There are six types oi variable-speed drives, as own in F ig. 29-73. Dynamic response indicates the ability of the drive to respond to a change in command it is measured in radians/second the higher the number, the faster the drive response. 

One topic of discussion is the measurements to which the operators pay the most attention (their foci). Of the myriad of measurements, there is a limited set that they find most important. These are the measurements that they use to make the short-cycle decisions. The important points to glean are the reasons they focus on these, the values and trends that they expect, and their responses to the deviations from these. 

Systems sueh as the EDS use a dual mieroproeessor system. As ean be seen in Figure 4-93, eritieal parameters of memory, input/output, alarm/trips, and host eomputer eommunieation are handled in the main proeessor. To maintain fast response time, this proeessor is kept free of less eritieal tasks sueh as operator interfaeing, trending, and arehiv-ing. A seeond proeessor, an administrative CPU, is used for these less eritieal yet important tasks. 

Along with, and closely connected to, the developments in precise impact techniques is the development of methods to carry out time-resolved materials response measurements of stress or particle velocity wave profiles. With time resolutions approaching 1 ns, these devices have enabled study of mechanical responses not possible in the early period of the 1960s. The improved time-resolutions have resulted from direct measurement of stress or particle velocity, rather than from improved accuracy and resolution in measurement of position and time. In a continuation of this trend, capabilities are being developed to provide direct measurements of the rate-of-change of stress. With the ability to measure such a derivative function, detailed study of new phenomena and improved resolution and accuracy in descriptions of known rate-dependent phenomena seem possible. 

User feedback should be obtained periodically, not just at the time of installation. As users gain familiarity with PSM systems, they may identify potential system breakdown points and improvement opportunities. In addition, evaluation of trends in the responses from survey to survey can help to Identify areas needing improvement and measure your success in improving systems. Where user survey responses suggest an improvement opportunity, you should involve those users in defining the opporhmity and in its analysis. The tools of Total Quality Management can be veiy useful in this effort. 

The LER data base served as the primary source of DG failure data, while a data base for DG successes was formed from nuclear plant licensees responses to a USNRC questionnaire (Generic Letter 84-15). Estimates of DG failure on demand were calculated from the LER data, DG test data, and response data from the questionnaire. The questionnaire also provided data on DG performance during complete and partial LOSP and in response to safety injection actuation signals. Trends in DG performance are profiled. The effects of testing schedules on diesel reliability are assessed. Individual failures are identified in an appendix. 

Decide if ion-dipole interactions are responsible for the observed substituent effects. Obtain the charge on carbon and nitrogen in each cyano group. What evidence is there for a polar CN bond Should the ion (O )-dipole (CN) interaction be stabilizing or destabilizing Can these interactions explain the trends in electrostatic potential (Hint Focus on changes in O—CN distance and in orientation of the cyano group.)... 

Identify the most negatively-charged and most positively-charged regions in each molecule. (Ignore the phenyl rings attached to triafulvene.) The dipole moments of these molecules have been measured as 6.3, 0 and 0.8 debyes. Which molecule is responsible for which dipole moment Explain the trend in dipole moments. 

The pull system requires that the suppliers to the component fabricator, the component fabricator, and the fabricator s customers work closely together. This is essential as there is little room for error that causes costly line down situations for the fabricators customer. The trend is also for each part of the chain, supplier, fabricator, and customer, to take responsibility for the quality and performance of their own products. This has resulted in a term in general use today, self-certified supplier. ... 

There has been not only gi owth m the total number of electric motors (more standard appliances in use), but also a proliferation in their use for new, novel applications. Both trends will continue to increase demand for the electricity to run electric motors. In the United States, electric motors arc responsible for consuming more than half of all electricity, and for the industrial sector alone, close to two-thirds. Since the cost of the electricity to power these motors is enormous (estimated at more than 90 billion a year), research is focused on finding ways to increase the energy efficiency of motors and motor systems. 

The exact position of the aldol equilibrium depends both on reaction conditions and on substrate structure. The equilibrium generally favors condensation product in the case of aldehydes with no a substituent (RCH2CHO) but favors reactant for disubstituted aldehydes (R2CHCHO) and for most ketones. Steric Factors are probably responsible for these trends, since increased substitution near the reaction site increases steric congestion in the aldol product. 

FIGURE 2.18 Inotropic and lusitropic responses of guinea pig left atria to (3-adrenoceptor stimulation. Panels A to C isometric tension waveforms of cardiac contraction (ordinates are mg tension abscissae are msec), (a) Effect of 0.3 nM isoproterenol on the waveform. The wave is shortened due to an increase in the rate of diastolic relaxation, whereas no inotropic response (change in peak tension) is observed at this concentration, (b) A further shortening of waveform duration (lusitropic response) is observed with 3 nM isoproterenol. This is concomitant with positive inotropic response (increase maximal tension), (c) This trend continues with 100 nM isoproterenol, (d) Dose-response curves for ino tropy (filled circles) and lusitropy (open circles) in guinea pig atria for isoproterenol, (e) Dose-response curves for inotropy (filled circles) and lusitropy (open circles) in guinea pig atria for the P-adrenoceptor partial agonist prenalterol. Data redrawn from [6]. 

Horvath CM (2000) STAT proteins and transcriptional responses to extracellular signals. Trends Biochem Sci 25 496-502... 

The values of sA and. ru are not well defined by kinetic data.59 61 The wide variation in. vA and for MMA-S copolymerization shown in Table 7.5 reflects the large uncertainties associated with these values, rather than differences in the rate data for the various experiments. Partly in response to this, various simplifications to the implicit penultimate model have been used (e.g. rA3rBA= W- and -Va=- h)- These problems also prevent trends in the values with monomer structure from being established. 

---