Titanium milling

Titanium malates, 25 89 Titanium metal, 25 61 Titanium methoxides, 25 78 Titanium mill shipments, 24 839 Titanium monosulfide, 25 57 Titanium monoxide, 25 13-14 Titanium monoxychloride, 25 53 Titanium nitrate, 25 10-11 Titanium nitride(s), 25 9-10... 

The titanium milling application would show a slightly better payback primarily due to high credits from the TiOg cake byproduct. 

Fig. 2 Cutting parameter during titanium milling (Sandvik Coromant 2010)...

For titanium milling applications, increased effort should be spend at the start for planning and preparation of the machining process. A stable machine tool, very rigid tool holders, and reduced tool overhangs should be applied. If machining with dedicated tools and carefully adapted process parameters, even titanium alloys can be machined with a high productivity. 

Direct synthesis from nitrogen and finely divided titanium metal can be achieved at temperatures of >ca 1200° C (4). Typically, titanium sponge or powder is heated in an ammonia- or nitrogen-filled furnace and the product is subsequently milled and classified. 

The resulting titanium nitride forms a sintered mass, which must be subsequently milled to form a powder having a wide size distribution. The powders produced by these routes ate typically 0.5—10 )Tm, with a wide size distribution. Very fine powders (0.005—0.5 -lm) have been prepared at pilot-plant scale... 

The Sulfate Process. A flow diagram for the sulfate process is shown in Figure 1. The strongly exothermic digestion of the dried, milled feedstock in 85—95°/ sulfuric acid converts metal oxides into soluble sulfates, primarily titanium and iron. 

Extraction of Bertrandite. Bertrandite-containing tuff from the Spor Mountain deposits is wet milled to provide a thixotropic, pumpable slurry of below 840 p.m (—20 mesh) particles. This slurry is leached with sulfuric acid at temperatures near the boiling point. The resulting beryUium sulfate [13510-49-1] solution is separated from unreacted soflds by countercurrent decantation thickener operations. The solution contains 0.4—0.7 g/L Be, 4.7 g/L Al, 3—5 g/L Mg, and 1.5 g/L Fe, plus minor impurities including uranium [7440-61-1/, rare earths, zirconium [7440-67-7] titanium [7440-32-6] and zinc [7440-66-6]. Water conservation practices are essential in semiarid Utah, so the wash water introduced in the countercurrent decantation separation of beryUium solutions from soflds is utilized in the wet milling operation. 

In iadustrial production of titanium carbide, pure (99.8%, with minor impurities of Si, Fe, S, P, and alkahes) titanium oxide [13463-67-7] Ti02, iu the dry or wet state is mixed iu 68.5 31.5 ratio with carbon black or finely milled low ash graphite. The dry mixture is pressed iato blocks that are heated iu a horizontal or vertical carbon-tube furnace at 1900—2300°C hydrogen that is free of oxygen and nitrogen serves as protective gas. In the vertical push-type furnaces, the Hberated CO itself provides protection. 

There are other methods of preparation that iavolve estabhshing an active phase on a support phase, such as ion exchange, chemical reactions, vapor deposition, and diffusion coating (26). For example, of the two primary types of propylene polymerization catalysts containing titanium supported on a magnesium haUde, one is manufactured usiag wet-chemical methods (27) and the other is manufactured by ball milling the components (28). 

Uhlig, H. H. and Gilman, 3. R., Inhibition of Pitting Corrosion of Stainless Steel 18/8 in Iron(III) Chloride Solutions by Nitrates , Z. Physik. Chem.,21/6, 127 (1964) C.A., 61,9231c Fisher, W. R., Pitting Corrosion, Especially of Titanium. 1 Corrosion Studies , Techn. Mill. 

Milling in a ball-mill (10, 149). In the activation of TiCl2 by ballmilling the average oxidation number of the titanium ions was changed however there was no dependence evident between the catalytic activity and the content of Ti(II) in the catalyst the proportional dependence of the activity on the specific surface was not observed either (10). 

Titanium nitride-based nanoparticles are also efficient dopants for NaAlH4 in hydrogen storage applications [12, 13]. The black solid TiN powder can be dispersed into the hydride via ball milling. Addition of titanium nitride-based na-... 

---