Thermoset plastic injection molding

Injection molding is a cyclic discontinuous process used to form three-dimensional plastic parts (25. 26). Both thermoplastics and thermosets are injection molded. The process is shown schematically in Figure 11 for a reciprocating screw injection molder. This type of a machine has a screw rotating in a barrel similar to an extruder. However, here the melt flow is discontinuous and controlled via a check valve at the tip of the screw. Material is melted in the extruder, and the melt is accumulated in front of the screw tip until sufficient melt is at hand to fill the mold cavity (cavities). 

Plastics - Injection molding of test specimens of thermosetting powder molding compounds (PMCs)... 

Shrinkage from mold cavity to molded dimensions of thermosetting plastics when molded by compression, injection, or transfer molding under specified conditions. ASTM D6289 specifies method of measurement. 

Deutsches Institut fiir Normung e. V. (DIN) Plastics - Injection molding of test specimens of thermosetting powder molding compounds (PMC) - Part 2 Small plates. Berlin Beuth-Veriag, 2000. 

Phenolic phenol formaldehydes (PFs) are the low-cost workhorse of the electrical industry (particularly in the past) low creep, excellent dimensional stability, good chemical resistance, good weatherability. Molded black or brown opaque handles for cookware are familiar applications. Also used as a caramel colored impregnating plastics for wood or cloth laminates, and (with reinforcement) for brake linings and many under-the-hood automotive electricals. There are different grades of phenolics that range from very low cost (with low performances) to high cost (with superior performances). The first of the thermosets to be injection-molded (1909). 

Important are behaviors associated and interrelated with plastic materials (thermoplastics, thermosets, elastomers, reinforced plastics, etc.) and fabricating processes (extrusion, injection molding, blow molding, forming, foaming, reaction injection molding, etc.). They are presented so that the technical or non-technical reader can readily understand the interrelationships. 

An important step in the manufacture of any plastic product is the fabrication or the shaping of the article. Most polymers used as plastics when manufactured are prepared in pellet form as they are expelled from the reactor. These are small pieces of material a couple of millimeters in size. This resin can then be heated and shaped by one of several methods. Thermoset materials are usually compression molded, cast, or laminated. Thermoplastic resins can be injection molded, extruded, or blow molded most commonly, with vacuum forming and calendering also used but to a lesser extent. 

Advanced Thermoplastics Materials. Thermoplastics and linear plastics of finite molecular weight that can be fabricated into very complex structures by hot melt or injection molding are different from the thermoset materials that require cross-linking to build up infinite molecular weight to form network (cross-link) structures. Advances in thermoplastic engineering materials include amorphous thermoplastics, crystalline thermoplastics, liquid crystal thermoplastics, and fluorinated thermoplastics (see Engineering plastics). 

The ring-opening metathesis polymerization of dicyclopentadiene was monitored by ultrasonic spectroscopy.16 The thermoset poly(dicyclopentadiene) is formed by ringopening and cross-linking in a reaction injection molding system. A reaction cell with a plastic window was constructed for use with pulse echo ultrasonic spectroscopy. Realtime measurements of density, longitudinal velocity, acoustic modulus and attenuation were monitored. Reaction kinetics were successfully determined and monitored using this technique. 

Reaction injection molding (RIM) is a fast, low-pressure, low-temperature, low-cost process for one-step conversion of reactive liquids into large finished solid plastic products. Liquid polyol and liquid diisocyanate are mixed by impingement, pumped instantly to fill a large mold cavity, and polymerize/ cure rapidly to form a thermoset polyurethane product. The cured polymer may be a stiffly flexible product such as automotive bumper covers, front ends, and trim or a rigid foamed product such as furniture and housings (cabinets) for computers, business machines, TY and radio. 

These plastics represent at least 90wt% of all plastics consumed worldwide. Unlike thermoset plastics, they are in many cases reproccssable without any or serious losses of properties. There are those than can have limitations of heat-distortion temperatures, cold flow and creep, and are more likely to be damaged by chemical solvent attack from paints, adhesives, and cleaners. When injection molded, dimensional integrity and ultimate strength are more dependent on the proper process control molding parameters than is generally the case with TSs. 

The process of injection molding (IM) is used principally for processing unreinforced or glass fiber reinforced thermoplastics (TPs) and thermosets (TSs) (Figure 4.1). Up to at least 90wt% of all plastics processed are TPs. There are many different types or designs of IM machines (IMMs) that permit molding many different products based on factors such as quantities, sizes (such as auto bumpers to medical micro products), shapes (simple to complex), product performances, and/or economics.1,150>157,173 176 476... 

Spin casting can use plastic molds, such as silicone, to produce close tolerance, highly cost effective, limited production in a variety of materials. The process uses easily adjustable centrifugal force to inject liquid thermoset plastics into a circular disc-shaped elastomeric mold under pressure, completely and rapidly filling the mold cavities. 

---