Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Thermal conductive detector

Alternatively, gas chromatography may be used Fig. XVII-5 shows a schematic readout of the thermal conductivity detector, the areas under the peaks giving the amount adsorbed or desorbed. [Pg.616]

Thermal Conductivity Detector One of the earliest gas chromatography detectors, which is still widely used, is based on the mobile phase s thermal conductivity (Figure 12.21). As the mobile phase exits the column, it passes over a tungsten-rhenium wire filament. The filament s electrical resistance depends on its temperature, which, in turn, depends on the thermal conductivity of the mobile phase. Because of its high thermal conductivity, helium is the mobile phase of choice when using a thermal conductivity detector (TCD). [Pg.569]

Zhou and colleagues determined the %w/w H2O in methanol by GG, using a capillary column coated with a nonpolar stationary phase and a thermal conductivity detector. A series of calibration standards gave the following results. [Pg.616]

Acrolein is produced according to the specifications in Table 3. Acetaldehyde and acetone are the principal carbonyl impurities in freshly distilled acrolein. Acrolein dimer accumulates at 0.50% in 30 days at 25°C. Analysis by two gas chromatographic methods with thermal conductivity detectors can determine all significant impurities in acrolein. The analysis with Porapak Q, 175—300 p.m (50—80 mesh), programmed from 60 to 250°C at 10°C/min, does not separate acetone, propionaldehyde, and propylene oxide from acrolein. These separations are made with 20% Tergitol E-35 on 250—350 p.m (45—60 mesh) Chromosorb W, kept at 40°C until acrolein elutes and then programmed rapidly to 190°C to elute the remaining components. [Pg.124]

Thermal conductivity is used as an analytical tool in the deterrnination of hydrogen. Because the thermal conductivities of ortho- and i7n -hydrogen are different, thermal conductivity detectors are used to determine the ortho para ratio of a hydrogen sample (240,241). In one method (242), an analy2er is described which spHts a hydrogen sample of unknown ortho para ratio into two separate streams, one of which is converted to normal hydrogen with a catalyst. The measured difference in thermal conductivity between the two streams is proportional to the ortho para ratio of the sample. [Pg.430]

By far the most used detector is the thermal conductivity detector (TCD). Detectors like the TCD are called bulk-property detectors, in that the response is to a property of the overall material flowing through the detector, in this case the thermal conductivity of the stream, which includes the carrier gas (mobile phase) and any material that may be traveling with it. The principle behind a TCD is that a hot body loses heat at a rate that depends on the... [Pg.107]

For measuring the inert species, some of which are present in the majority of gases, the thermal-conductivity detector (TCD) is often the detector of choice for gas analyses. Since the TCD is a concentration detector and its sensitivity is lower than that of mass-flow detectors such as the flame-ionization detector (FID), relatively high concentrations of compounds in the carrier gas are needed. This means that packed columns, with their high loadability, are still quite popular for such analyses. [Pg.381]

Figure 14.6 Schematic diagram of a five-column cliromatographic refinery analyser system SL, sample loop V1, two-way valve to block the sample line V2 and V5, ten-port valves V3 and V4, six-way valves Cl C5, packed columns R, restriction TCD, thermal conductivity detector-. Figure 14.6 Schematic diagram of a five-column cliromatographic refinery analyser system SL, sample loop V1, two-way valve to block the sample line V2 and V5, ten-port valves V3 and V4, six-way valves Cl C5, packed columns R, restriction TCD, thermal conductivity detector-.
Thermal conductivity detector. The most important of the bulk physical property detectors is the thermal conductivity detector (TCD) which is a universal, non-destructive, concentration-sensitive detector. The TCD was one of the earliest routine detectors and thermal conductivity cells or katharometers are still widely used in gas chromatography. These detectors employ a heated metal filament or a thermistor (a semiconductor of fused metal oxides) to sense changes in the thermal conductivity of the carrier gas stream. Helium and hydrogen are the best carrier gases to use in conjunction with this type of detector since their thermal conductivities are much higher than any other gases on safety grounds helium is preferred because of its inertness. [Pg.241]

Determination of oxygen. The sample is weighed into a silver container which has been solvent-washed, dried at 400 °C and kept in a closed container to avoid oxidation. It is dropped into a reactor heated at 1060 °C, quantitative conversion of oxygen to carbon monoxide being achieved by a layer of nickel-coated carbon (see Note). The pyrolysis gases then flow into the chromatographic column (1 m long) of molecular sieves (5 x 10-8 cm) heated at 100 °C the CO is separated from N2, CH4, and H2, and is measured by a thermal conductivity detector. [Pg.248]

Thermal Conductivity Detector In the thermal conductivity detector (TCD), the temperature of a hot filament changes when the analyte dilutes the carrier gas. With a constant flow of helium carrier gas, the filament temperature will remain constant, but as compounds with different thermal conductivities elute, the different gas compositions cause heat to be conducted away from the filament at different rates, which in turn causes a change in the filament temperature and electrical resistance. The TCD is truly a universal detector and can detect water, air, hydrogen, carbon monoxide, nitrogen, sulfur dioxide, and many other compounds. For most organic molecules, the sensitivity of the TCD detector is low compared to that of the FID, but for the compounds for which the FID produces little or no signal, the TCD detector is a good alternative. [Pg.201]

The gas chromatograph (GC) is a Hewlett-Packard 5890 GC with a thermal conductivity detector. A 5A mole sieve column is used with argon carrier gas this gives peaks going in the same direction for both hydrogen and nitrogen. [Pg.535]

The gas chromatograph is better to be equipped both with a thermal conductivity detector (TCD) and with a flame ionization detector (FID). The latter is extremely useful in the analysis of organic substances at low concentrations. Packed columns are normally used, although capillary columns offer certain advantages in the analysis of a variety of products. Some of the major companies that supply gas chromatographs are ... [Pg.548]

As the vapor leaves the tube, the compounds in the sample are detected by a device such as a thermal conductivity detector. This instrument continuously measures the thermal conductivity (the ability to conduct heat) of the carrier gas, which changes when a solute is present. The detection techniques are very sensitive, allowing tiny amounts of solutes to be detected. Many environmental monitoring and forensic applications have been developed. [Pg.476]

Hydrogen detection in this type of meter is achieved using an ion pump, mass spectrometry or thermal conductivity detectors. ... [Pg.339]

Catalytic activity for the selective oxidation of H2S was tested by a continuous flow reaction in a fixed-bed quartz tube reactor with 0.5 inch inside diameter. Gaseous H2S, O2, H2, CO, CO2 and N2 were used without further purification. Water vapor (H2O) was introduced by passing N2 through a saturator. Reaction test was conducted at a pressure of 101 kPa and in the temperature range of 150 to 300 °C on a 0.6 gram catalyst sample. Gas flow rates were controlled by a mass flow controller (Brooks, 5850 TR) and the gas compositions were analyzed by an on-line gas chromotograph equipped with a chromosil 310 coliunn and a thermal conductivity detector. [Pg.426]

TEM observation and elemental analysis of the catalysts were performed by means of a transmission electron microscope (JEOL, JEM-201 OF) with energy dispersion spectrometer (EDS). The surface property of catalysts was analyzed by an X-ray photoelectron spectrometer (JEOL, JPS-90SX) using an A1 Ka radiation (1486.6 eV, 120 W). Carbon Is peak at binding energy of 284.6 eV due to adventitious carbon was used as an internal reference. Temperature programmed oxidation (TPO) with 5 vol.% 02/He was also performed on the catalyst after reaction, and the consumption of O2 was detected by thermal conductivity detector. The temperature was ramped at 10 K min to 1273 K. [Pg.518]

The catalytic reforming of CH4 by CO2 was carried out in a conventional fixed bed reactor system. Flow rates of reactants were controlled by mass flow controllers [Bronkhorst HI-TEC Co.]. The reactor, with an inner diameter of 0.007 m, was heated in an electric furnace. The reaction temperatoe was controlled by a PID temperature controller and was monitored by a separated thermocouple placed in the catalyst bed. The effluent gases were analyzed by an online GC [Hewlett Packard Co., HP-6890 Series II] equipped with a thermal conductivity detector (TCD) and carbosphere column (0.0032 m O.D. and 2.5 m length, 80/100 meshes), and identified by a GC/MS [Hewlett Packard Co., 5890/5971] equipped with an HP-1 capillary column (0.0002 m O.D. and 50 m length). [Pg.614]

The general operation of the pilot scale reactor has be previously described by Pareek et. al. [3]. However, modifications were required to allow the injection of the gas and liquid tracers, and their subsequent detection at the outlets. The liquid tracer, 5mL Methyl blue solution (lOgL" ), was injected via a syringe inserted into the liquid feed line. Outlet samples were measured with a Shimadzu 1601 UV-Vis Spectrophotometer at a wavelength of 635nm. A pulse (20mL) of helium gas tracer was introduced using an automated control system, with the outlet concentration monitored in real-time with a thermal conductivity detector. Runs were carried out based on a two-level... [Pg.669]

The instrumentation for temperature-programmed investigations is relatively simple. The reactor, charged with catalyst, is controlled by a processor, which heats the reactor at a linear rate of typically 0.1 to 20 °C min . A thermal conductivity detector or, preferably, a mass spectrometer measures the composition of the outlet gas. [Pg.154]

The activity tests of the catalyst were carried out in a microflow reactor set-up in which all the high temperature parts are constructed of hastelloy-C and monel. The reactor effluent was analyzed by an on-line gas chromatograph with an Ultimetal Q column (75 m x 0.53 mm), a flame ionization detector, and a thermal conductivity detector. The composition of the feed to the reactor can be varied, besides the temperature, pressure, and space velocity. The influence of the recycle components CHCIF2 and methane was tested by adding these components to the feed. In total five stability experiments of over 1600 hours were performed. In each... [Pg.370]

The product gases were continuously analyzed for NO and NO2 using a chemiluminescent analyzer, and discontinuously for N2O, N2, CO, CO2 and O2 by GC equipped with a thermal conductivity detector and an electron capture detector, specifically for the N2O analysis, using a Poraplot Q column and a molsieve 5A column for separation. [Pg.643]


See other pages where Thermal conductive detector is mentioned: [Pg.569]    [Pg.570]    [Pg.578]    [Pg.609]    [Pg.612]    [Pg.779]    [Pg.440]    [Pg.15]    [Pg.430]    [Pg.106]    [Pg.110]    [Pg.765]    [Pg.236]    [Pg.241]    [Pg.248]    [Pg.248]    [Pg.875]    [Pg.78]    [Pg.945]    [Pg.102]    [Pg.150]    [Pg.214]    [Pg.250]    [Pg.458]    [Pg.309]    [Pg.554]   
See also in sourсe #XX -- [ Pg.326 ]




SEARCH



Chromatography thermal conductivity detector

Detector Thermal detectors

Detector conductance

Detector thermal conductivity

Detector thermal conductivity

Detector, atomic spectrometer thermal conductivity

Detectors conductivity

Process thermal conductivity detector

The Thermal Conductivity Detector

The Thermal Conductivity Detector (TCD)

Thermal conductivity detector (TCD

Thermal conductivity detector application

Thermal conductivity detector design

Thermal conductivity detector for

Thermal conductivity detector geometry

Thermal conductivity detector in gas chromatography

Thermal conductivity detector katharometer)

Thermal conductivity detector mechanism

Thermal conductivity detector modulated

Thermal conductivity detector operation

Thermal conductivity detector performance

Thermal conductivity detector response characteristics

Thermal conductivity detector sensitivity

Thermal conductivity detectors, lead

Thermal conductivity detectors, lead analysis

Thermal detectors

© 2024 chempedia.info