Technology use

The objective of this book is to provide a comprehensive introduction to the upstream industry useful for industry professionals who wish to be better informed about the basic methods, concepts and technology used. It is also Intended for readers not directly working in oil and gas companies but who are providing related support services. 

Representative set of weldments was examined site welds (with pearlitic type weld metal) and two types of site weld repair zones with different welding technologies using Cr-Ni filler metals and Ni-based alloy. Results of AUGUR 4.2 inspection were compared with manual ultrasonic inspection ones in terms of defect detection, characterization, positioning and sizing in order to estimate correlation between these data. 

Liquid- and vapor-phase processes have been described the latter appear to be advantageous. Supported cadmium, zinc, or mercury salts are used as catalysts. In 1963 it was estimated that 85% of U.S. vinyl acetate capacity was based on acetylene, but it has been completely replaced since about 1982 by newer technology using oxidative addition of acetic acid to ethylene (2) (see Vinyl polymers). In western Europe production of vinyl acetate from acetylene stiU remains a significant commercial route. 

Chemical, cultural, and mechanical weed control practices have been relatively successful ia reducing yield losses from weeds (448). However, herbicide-resistant weed populations, soil erosion, pesticide persistence ia the environment, and other problems associated with technologies used (ca 1993) to control weeds have raised concerns for the long-term efficacy and sustainability of herbicide-dependent crop production practices (449). These concerns, coupled with ever-increasing demands for food and fiber, contribute to the need for innovative weed management strategies (450). 

There are many possible means for quantification of the antigen—antibody reaction. Immunoassays may be classified according to the technology used for detection and quantification of the analyte being detected. 

A second type of uv curing chemistry is used, employing cationic curing as opposed to free-radical polymerization. This technology uses vinyl ethers and epoxy resins for the oligomers, reactive resins, and monomers. The initiators form Lewis acids upon absorption of the uv energy and the acid causes cationic polymerization. Although this chemistry has improved adhesion and flexibility and offers lower viscosity compared to the typical acrylate system, the cationic chemistry is very sensitive to humidity conditions and amine contamination. Both chemistries are used commercially. 

Although practical generation of energy by laser-assisted thermonuclear fusion remains well ia the future, the program has provided some of the most exacting requirements for laser technology and has led to advances ia laser equipment that have been adopted ia other areas. Thus the research and development associated with thermonuclear fusion work has helped to spur advances ia laser technology useful for many other appHcations. 

Battery breaking technologies use wet classification to separate the components of cmshed batteries. Before cmshing, the sulfuric acid is drained from the batteries. The sulfuric acid is collected and stored for use at a later stage in the process, or it may be upgraded by a solvent extraction process for reuse in battery acid. 

One technology uses bovine somatotropin (bST) produced by recombinant technology (38). Somatotropin [9002-72-6] is a growth hormone. The bST-supplemented cows provide an increase in milk output per cow or an increased feed efficiency. Recombinant bST, also known as recombinant bovine growth hormone (rBGH) is the synthetic analogue of a natural hormone that increases milk production in cows (39). The use of recombinant technology was approved by the FDA in 1993. The Commission of the European Community has recommended that the moratorium on commercial use of BGH be delayed until the year 2000. 

Primary production typically recovers 10—25% of the oil originally ia the reservoir. Efficiency of primary production is related to oil properties, reservoir properties, geometric placement of oil wells, and the drilling and completion technology used to drill the wells and prepare them for production. Pumping the well can maintain production at economic levels for years. 

The various preparation processes and technologies used in dmg product manufacture also can effect product safety, stabihty, and performance, eg, compression during tablet manufacture. The principal processes used in dosage form manufacture are as foUows (15). 

The most effective phosphoms production technology uses a submerged arc furnace. The submerged arc furnace performs three functions chemical reactor, heat-exchanger, and gas—soHd filter, respectively, each of which requires a significant amount of preparation for the soHd furnace feed materials. 

Much of the technology used in the reclamation of metals from metal-bearing wastes was developed by the mining iadustries. The primary means of recycling metal from metal and alloyed scrap is via pyrometaHurgy (see Metallurgy). 

Solar-thermal technology uses tracking mirrors to concentrate sunlight onto a receiver. In turn, the receiver absorbs solar energy as heat, warming a fluid that then drives a turbine generator. Most solar-thermal plants requite cooling water. 

Market Access. Technology organizations must understand the value chain, ie, the sources of demand for the firm s products and services the technologies used by customers, learned through a vibrant appHcations development effort and the ways ia which technological solutions can affect demand. This overall effort requires close contact with the firm s marketing function and with customers ia their markets, so that technologies and markets can be matched. 

---