Tanks and pipes

Ammonia is corrosive to akoys of copper and zinc and these materials must not be used in ammonia service. Iron or steel should usuaky be the only metal in ammonia storage tanks, piping, and fittings. It is recommended that ammonia should contain at least 0.2% water to prevent steel stress corrosion. Mercury thermometers should be avoided. 

DOT 17E phenolic-lined steel pails and dmms, respectively. Plain steel is not suitable for isopropyl alcohol containing water because msting can result. Instead, baked phenolic-lined steel tanks are used. Aluminum is also unsuitable. It is attacked by isopropyl alcohol, especially the anhydrous grade, resulting ia the formation of aluminum isopropoxide. Containers must comply with DOT specifications. Tanks, piping, and equipment can be made of similar material. 

Shipment and Storage. Sulfur dichloride, if kept dry, is noncorrosive at ambient temperatures, thus carbon steel and Hon can be used Hi the constmction of tanks, piping, and dmms. However, when water or humidity is present, materials resistant to hydrochloric acid must be used, eg, glass-lined pipe. Teflon, titanium, HasteUoy C, or possibly a chemically resistant, glass-reiaforced polyester. Threaded pipe joHits should be assembled with Teflon tape. Hoses should be constmcted with a Teflon inner lining with the outer tube constmcted of Neoprene or braided 316 stainless steel protected by an adequate thickness of Teflon. Sulfur dichloride should be stored away from heat and away from dHect rays of the sum. Toluene and sulfur dichloride react exothermically when catalyzed by Hon or ferric chloride. Safety precautions should be foUowed when such a mixture is present (165). 

Waters While MIC-causing bacteria may arrive at the surface of their corrosion worksite by almost any transportation system, there is always water present to allow them to become ac tive and cause MIC to occur. There are plenty of examples of even superpure waters having sufficient microorganisms present to feed, divide, and multiply when even the smallest trace of a viable food-stuff is present (e.g., the so-called watei for injection in the pharmaceutical industiy has been the observed subject of extensive corrosion of pohshed stainless steel tanks, piping, and so on). 

Tanks and Appurtenances Used to Contain Hazard Substances Including Aboveground Tanks, Underground Tanks, Piping and Appurtenances, and Storm Water Management Systems Associated witb Containment Systems... 

Electrochemical corrosion protection of the internal surfaces of reaction vessels, tanks, pipes and conveyor equipment in the chemical, power and petroleum industries is usually carried out in the presence of strongly corrosive media. The range stretches from drinking water through more or less contaminated river, brackish and seawater frequently used for cooling, to reactive solutions such as caustic soda, acids and salt solutions. 

Solvent reeovery systems would also neeessitate the speeifieation of eondenser duties, distillation tower sizes, holding tanks, piping, and valves. It is important to note that the engineering design of an adsorption system should be based on pilot data for the partieular system. Information ean usually be obtained direetly from the adsorbent manufaeturer. The overall size of the unit is determined primarily by eeonomie eonsiderations, balaneing the operating eosts against the eapital eosts. 

Additional recommendations are provided in STP-ST-003, Hydrogen Standardization Interim Report for Tanks, Piping, and Pipelines (ASME, May 2005), and STP-ST-006, Design Guide for Hydrogen Piping and Pipelines (ASME, December 2007). 

Wulpi provides an excellent overview of failure mechanisms for mechanical parts in his book Understanding How Components Fait.A The book contains a number of photographs that compare the different types of failures. It is a good reference for mechanical component failnres including shafts, tanks, piping, and boilers. 

Epoxies show superior adhesion to metals and glass, and have limited shrinkage during cure. They are used for surface coatings, as adhesives and rc>r laminating to produce plastic tanks, pipe, and aircraft parts, etc (Ref 3, p 445-R). They also have been used in manuf of plastics (Ref 1), construction of rockets St missiles (Ref 2) and in manuf of explosive compositions of improved mechanical and thermal stability (Ref 4)... 

A wide range of rubbers are available for successful use as materials of construction and are applied in areas such as handling inorganic salt solutions where metals are unsuitable. The use of rubber linings is widespread in equipment such as tanks, pipes, and drums and most other critical chemical equipment. However, their use is limited to moderate temperatures, and they are generally suitable for use in abrasive duties. Some of the more commonly used plastics are PVC, PTFE and polypropylene. 

Practical Information on Aging of Pressure Vessels, Tanks, Piping, and Safety Critical Instruments... 

Fresh water. Aluminum and its alloys are not prone to corrosion on exposure to distilled water up to 180°C. Thus storage tanks, piping and fittings of the alloy can be used for handling distilled water. The composition of natural fresh water is variable. In spite of this restriction, the alloys are not attacked, even at 180°C in natural waters. It should be noted that pitting may occur when a small thickness of the sample is exposed. In this case Alclad 3003 is recommended for use to avoid failure due to pitting. 

Hydrogen Standardization Interim Report for Tanks, Piping, and Pipelines, ASME, New York, 2005. 

The purging of tanks, pipes, and other kinds of containers with nitrogen can also prevent the possibility of fires. In the petroleum industry, for example, the processing of organic compounds in the presence of air creates the possibility of fires, a possibility that can be avoided by covering the reactants with pure nitrogen. 

---