Suspension polymerization particle size

Polymer Areas Suspension polymerization, particle size control stabilizes surface tesnion of latexes. Modifies latex surface active properties. Polymer can be easily recovered. 

Microsuspension and Inverse-microsuspension. In suspension polymerizations, particle formation occurs through a droplet breakup-coalescence mechanism, with the diameter controlled by the temperature, interfacial tension, agitation intensity and conversion. Suspension polymerizations have typically been characterized by an initiator soluble in the monomer phase and particle diameters in the 50-1000 pm range [40]. Smaller particles (0.2-20 pm) have been produced at higher agitation speeds (lower interfadal tensions) [41] and in such cases a prefix micro has been added to the nomenclature (microsuspension) to reflect both the dominant synthesis conditions (suspension) and the nominal particle size (1 micron). Therefore, microsuspension polymerization has historically referred to a subdomain of suspension polymerization occurring at smaller particle sizes. Based on an analogy to this nomenclature, inverse-microsuspension polymerization has been proposed for similar water-in-oil... 

During suspension polymerization, drop size depends on the physical properties of the two phases, the phase ratio, the nature of the suspension flow, and the condition of the phase interface. Interfacial tension and drop stability depend largely on the nature of the drop stabilizer. If no stabilizer were used to protect the drops, the suspension would be unstable and the final polymer particles would reach an undesirable size. 

Polymerization occurs in particles whose dimensions are in the nanometer size range, perhaps 10 times smaller than the particles in suspension polymerization. 

Suspension polymerization of VDE in water are batch processes in autoclaves designed to limit scale formation (91). Most systems operate from 30 to 100°C and are initiated with monomer-soluble organic free-radical initiators such as diisopropyl peroxydicarbonate (92—96), tert-huty peroxypivalate (97), or / fZ-amyl peroxypivalate (98). Usually water-soluble polymers, eg, cellulose derivatives or poly(vinyl alcohol), are used as suspending agents to reduce coalescence of polymer particles. Organic solvents that may act as a reaction accelerator or chain-transfer agent are often employed. The reactor product is a slurry of suspended polymer particles, usually spheres of 30—100 pm in diameter they are separated from the water phase thoroughly washed and dried. Size and internal stmcture of beads, ie, porosity, and dispersant residues affect how the resin performs in appHcations. 

There are two principal PVC resins for producing vinyl foams suspension resin and dispersion resin. The suspension resin is prepared by suspension polymerization with a relatively large particle size in the 30—250 p.m range and the dispersion resin is prepared by emulsion polymerization with a fine particle size in the 0.2—2 p.m range (245). The latter is used in the manufacture of vinyl plastisols which can be fused without the appHcation of pressure. In addition, plastisol blending resins, which are fine particle size suspension resins, can be used as a partial replacement for the dispersion resin in a plastisol system to reduce the resin costs. 

A Gaussian distribution of particle size is the result of copolymer manufactured by suspension polymerization. A jetting process produces beads with more uniform particle size. The uniformity coefficient is a numerical method of indicating closeness of all beads to the same size. 

In a suspension polymerization, monomer is suspended ia water as 0.1—5 mm droplets, stabilized by protective coUoids or suspending agents. Polymerization is initiated by a monomer-soluble initiator and takes place within the monomer droplets. The water serves as both the dispersion medium and a heat-transfer agent. Particle size is controlled primarily by the rate of agitation and the concentration and type of suspending aids. The polymer is obtained as small beads of about 0.1—5 mm in diameter, which are isolated by filtration or centrifugation. 

Emulsion Polymerization. When the U.S. supply of natural mbber from the Far East was cut off in World War II, the emulsion polymerization process was developed to produce synthetic mbber. In this complex process, the organic monomer is emulsified with soap in an aqueous continuous phase. Because of the much smaller (<0.1 jira) dispersed particles than in suspension polymerization and the stabilizing action of the soap, a proper emulsion is stable, so agitation is not as critical. In classical emulsion polymerization, a water-soluble initiator is used. This, together with the small particle size, gives rise to very different kinetics (6,21—23). 

Suspension Polymerization. At very low levels of stabilizer, eg, 0.1 wt %, the polymer does not form a creamy dispersion that stays indefinitely suspended in the aqueous phase but forms small beads that setde and may be easily separated by filtration (qv) (69). This suspension or pearl polymerization process has been used to prepare polymers for adhesive and coating appHcations and for conversion to poly(vinyl alcohol). Products in bead form are available from several commercial suppHers of PVAc resins. Suspension polymerizations are carried out with monomer-soluble initiators predominantly, with low levels of stabilizers. Suspension copolymerization processes for the production of vinyl acetate—ethylene bead products have been described and the properties of the copolymers determined (70). Continuous tubular polymerization of vinyl acetate in suspension (71,72) yields stable dispersions of beads with narrow particle size distributions at high yields. 

In the suspension polymerization of PVC, droplets of monomer 30—150 p.m in diameter are dispersed in water by agitation. A thin membrane is formed at the water—monomer interface by dispersants such as poly(vinyl alcohol) or methyl cellulose. This membrane, isolated by dissolving the PVC in tetrahydrofuran and measured at 0.01—0.02-p.m thick, has been found to be a graft copolymer of polyvinyl chloride and poly(vinyl alcohol) (4,5). Early in the polymerization, particles of PVC deposit onto the membrane from both the monomer and the water sides, forming a skin 0.5—5-p.m thick that can be observed on grains sectioned after polymerization (4,6). Primary particles, 1 p.m in diameter, deposit onto the membrane from the monomer side (Pig. 1), whereas water-phase polymer, 0.1 p.m in diameter, deposits onto the skin from the water side of the membrane (Pig. 2) (4). These domain-sized water-phase particles may be one source of the observed domain stmcture (7). 

New templated polymer support materials have been developed for use as re versed-phase packing materials. Pore size and particle size have not usually been precisely controlled by conventional suspension polymerization. A templated polymerization is used to obtain controllable pore size and particle-size distribution. In this technique, hydrophilic monomers and divinylbenzene are formulated and filled into pores in templated silica material, at room temperature. After polymerization, the templated silica material is removed by base hydrolysis. The surface of the polymer may be modified in various ways to obtain the desired functionality. The particles are useful in chromatography, adsorption, and ion exchange and as polymeric supports of catalysts (39,40). 

A novel cross-linked polystyrene-divinylbenzene copolymer has been produced from suspension polymerization with toluene as a diluent, having an average particle size of 2 to 50 /rm, with an exclusive molecular weight for the polystyrene standard from about 500 to 20,000 in gel-permeation chromatography. A process for preparing the PS-DVB copolymer by suspension polymerization in the presence of at least one free-radical polymerization initiator, such as 2,2 -azo-bis (2,4-dimethylvaleronitrile) with a half-life of about 2 to 60 min at 70°C, has been disclosed (78). 

Each of the PLgel individual pore sizes is produced hy suspension polymerization, which yields a fairly diverse range of particle sizes. For optimum performance in a chromatographic column the particle size distribution of the beads should be narrow this is achieved by air classification after the cross-linked beads have been washed and dried thoroughly. Similarly, for consistent column performance, the particle size distribution is critical and is another quality control aspect where both the median particle size and the width of the distribution are specified. The efficiency of the packed column is extremely sensitive to the median particle size, as predicted by the van Deemter equation (4), whereas the width of the particle size distribution can affect column operating pressure and packed bed stability. 

Various novel applications in biotechnology, biomedical engineering, information industry, and microelectronics involve the use of polymeric microspheres with controlled size and surface properties [1-31. Traditionally, the polymer microspheres larger than 100 /urn with a certain size distribution have been produced by the suspension polymerization process, where the monomer droplets are broken into micron-size in the existence of a stabilizer and are subsequently polymerized within a continuous medium by using an oil-soluble initiator. Suspension polymerization is usually preferred for the production of polymeric particles in the size range of 50-1000 /Ltm. But, there is a wide size distribution in the product due to the inherent size distribution of the mechanical homogenization and due to the coalescence problem. The size distribution is measured with the standard deviation or the coefficient of variation (CV) and the suspension polymerization provides polymeric microspheres with CVs varying from 15-30%. 

A new process, from Norway, has filled the size gap between emulsion and suspension polymerization techniques [7,8]. This novel polymerization method, the so-called swollen emulsion polymerization has been developed by Ugelstad for producing uniform polymeric particles in the size range of 2-100 /nm. This process comprises successive swelling steps and repolymerizations for increasing the particle size of seed polymer particles by keeping the monodispersity of the seed latex. 

Manufacture of highly water-absorbent polymers with uniform particle size and good flowability can be carried out by reverse phase suspension polymerization of (meth)acrylic acid monomers in a hydrocarbon solvent containing crosslinker and radical initiator. Phosphoric acid monoester or diester of alka-nole or ethoxylated alkanole is used as surfactant. A polymer with water-absorbent capacity of 78 g/g polymer can be obtained [240]. 

---