Surface mounted device

Ru02 resistors are commercial small-power (volume of few mm3) electronic components. They belong to the group of smd (surface mount device) thick-film resistors and are... 

Platinum thin-film sensors are available in a broad variety of forms. Depending on the proposed application, the sensor may be unhoused, encapsulated in ceramic, configured as a surface mounted device (SMD) or located within a plastic housing with rigid pins. An overview of the variety of different forms currently available is given below (Fig. 5.2). 

Pricing as well as reliability considerations have led to an almost exclusive use of Si-based (i.e. Si and SOI) micro machined devices. Packaging and assembly has focused on ceramics (A1203, AIN, Low Temperature Co-fired Ceramics LTCC), Printed Circuit Board (PCB-) and Surface Mount Device (SMD-) technology and multichip modules (MCM s). 

Surface-mount devices, surface-mount interconnection devices, PCMCIA card frames... High-performance motor components... 

The class of ferroelectric materials have a lot of useful properties. High dielectric coefficients over a wide temperature and frequency range are used as dielectrics in integrated or in smd (surface mounted device) capacitors. The large piezoelectric effect is applied in a variety of electromechanical sensors, actuators and transducers. Infrared sensors need a high pyroelectric coefficient which is available with this class of materials. Tunable thermistor properties in semiconducting ferroelectrics are used in ptcr (positive temperature coefficient... 

Note that the sort of oscillator circuit shown in Rgure 6.13(b) can be constructed by the interconnection of line-powered modular instnnnentaticm [30], by the use of printed-circuit board-mounted, DC-powered components [31], by the use of surface-mount devices on a suitably metallized substrate, or even on a sin-... 

Figure 1.51 (a) Ta capacitors as surface mounted devices (SMD) (b) corresponding schemes (c) SEM of sponge-like anode after oxide formation (d) SEM with cross-section through aTa/Ta205 particle. 

CBA. [HernonMfg.] Chip bonding adhesives for bonding surface mounted devices to printed circuit board assemblies. 

Buffa, M. (1985), Process Control for Automatic Component Assembly of Surface Mounted Devices Utilizing a Machine Vision Controller, SME Vision 85 Conference Proceedings, Society of Manufacturing Engineers, Dearborn, MI, pp. 5.180-5.200. 

SMART (subjective multiattribute rating technique), 2195 SmartEcon.com, 266, 267 SmartErog, 273 SMART goals, 1005, 1009 SMDs, see Surface-mounted devices SMED (single-minute exchange of dies), 547 SMEs (small and medium-sized enterprises), 286... 

Eccobond D125F/Henkel Stencil application for surface-mount devices (capacitors, resistors, small outline ICs, and plastic leadless chip carriers) N/A N/A N/A... 

Epoxy, capillary N/A Surface-mount devices to Hand, time-pressure. Reworkable CSP, flip... 

Many aerobic formulations can be heat cured, but only between two surfaces. Table 1 shows the heat curing properties in an adhesive used to fix surface mount devices onto printed circuit boards compared to a typical epoxy and a typical anaerobic formulation used for the same purpose. 

Chipbonder 3617/ Loctite Stencil application for surface-mount devices requiring high speed and hi wet strengths 32,000/NA 300-550 Rounded 60-100 mm/sec (2.4-3.9 in/sec), snap-off [1 mm (39 mils)], squeegee pressure (4—6 N/cm)... 

Fig. 1. A syringed adhesive used for bonding surface-mounted devices on to printed circuit boards...

A large and increasing part of the fixed resistor market is taken by surface mounted device (SMD) resistors. These resistors are mounted dhectly on the printed circuit board. Electrical contacts are provided at the sides of the resistor. 

---