Strong, the

CoAsS, are also used as sources. The ore is roasted and Co is precipitated as the hydroxide and then reduced to Co with carbon (hep below 417 - C, cep to m.p.). The metal is silvery white and readily polished. It dissolves in dilute acids and is slowly oxidized in air. Adsorbs hydrogen strongly. The main use of cobalt is in alloys. Cobalt compounds are used in paints and varnishes, catalysts. Cobalt is an essential element in the diet. World production 1976 32 000 tonnes metal. 

After reviewing various earlier explanations for an adsorption maximum, Trogus, Schechter, and Wade [244] proposed perhaps the most satisfactory one so far (see also Ref. 243). Qualitatively, an adsorption maximum can occur if the surfactant consists of at least two species (which can be closely related) what is necessary is that species 2 (say) preferentially forms micelles (has a lower CMC) relative to species 1 and also adsorbs more strongly. The adsorbed state may also consist of aggregates or hemi-micelles, and even for a pure component the situation can be complex (see Section XI-6 for recent AFM evidence of surface micelle formation and [246] for polymeric surface micelles). Similar adsorption maxima found in adsorption of nonionic surfactants can be attributed to polydispersity in the surfactant chain lengths [247], Surface-active impuri-... 

PHOTOLYSIS OF AMMONIA. Restricting the discussion to neutral species only (ionic ones require high energy, and are not important in the 170-220-nm UV range, where ammonia absorbs strongly), the two low-energy reaction channels to ground state products are... 

Lithium is presently being recovered from brines of Searles Lake, in California, and from those in Nevada. Large deposits of quadramene are found in North Carolina. The metal is produced electrolytically from the fused chloride. Lithium is silvery in appearance, much like Na and K, other members of the alkali metal series. It reacts with water, but not as vigorously as sodium. Lithium imparts a beautiful crimson color to a flame, but when the metal burns strongly, the flame is a dazzling white. 

Application of an electric field between two metal electrodes causes a few ions and electrons to be desorbed and is surface or thermal emission (see Chapter 7 for more information on thermal ionization). Unless the electrodes are heated strongly, the number of electrons emitted is very small, but, even at normal temperatures, this emission does add to the small number of electrons caused by cosmic radiation and is continuous. 

When the ligands interact more strongly the MOs of the ligands must be taken into account. This type of MO theory is referred to as ligand field theory. 

In small pieces or as inserts, laminates may be used unsupported because they are quite stiff and strong. The modulus of a high pressure decorative laminate is about 7 GPa (106 psi) at room temperature. Thick laminates range up to 25 mm and are very strong, having flexual strength of 130 MPa (19,000 psi). These products are used unsupported as toilet partitions, laboratory tops, and so forth. 

Many chemical elements exhibit catalytic activity (5) which, within limits, is inversely related to the strength of chemisorption of the VOCs and oxygen, provided that adsorption is sufficiently strong to achieve a high surface coverage (17). If the chemisorption is too strong, the catalyst is quickly deactivated as the active sites become irreversibly covered. If the chemisorption is too weak, only a small fraction of the surface is covered and the activity is very low (17) (Fig. 2). 

The anion-exchanger concentration is shown not to influence strongly the exchange constants. It indicates that there is no either the extractant or compound formed in the organic phase self-association. 

The results obtained indicate that the ion-exchanger nature, generally not taken into account when developing ISEs for alkylammonium cations, actually influences strongly the selectivity of such ISEs and should be paid attention to when choosing optimal membrane composition. These data will be useful for finding ways to control the ISEs selectivity by rational choice of the membrane composition. 

Sodium acetate [127-09-3] M 82.0, m 324°, d 1.53. Crystd from acetic acid and pumped under vacuum for lOh at 120°. Alternatively, crystd from aqueous EtOH, as the trihydrate. This material can be converted to the anhydrous salt by heating slowly in a porcelain, nickel or iron dish, so that the salt liquefies. Steam is evolved and the mass again solidifies. Heating is now increased so that the salt melts again. (NB if it is heated too strongly, the salt chars.) After several minutes, the salt is allowed to solidify and cooled to a convenient temperature before being powdered and bottled (water content should now less than 0.02%). 

In the past ten years laboratory workers have become increasingly conscious of safety in the laboratory environment. We have therefore in three places in Chapter 1 (pp. 3 and 33, and bibliography p. 52) stressed more strongly the importance of safety in the laboratory. Also, where possible, in Chapters 3 and 4 we draw attention to the dangers involved with the manipulation of some hazardous substances. 

One cannot emphasize too strongly the importance of direct, time-resolved experimental observation of microscale phenomena in establishing sound theories of microstructural effects under conditions of shock-wave compression. 

For many years vinyl chloride-vinyl acetate copolymers had two main uses, in flooring compositions and for long playing gramophone records. Whereas the former application remains strong, the use in gramophone records has dropped sharply, particularly since the widespread acceptance of polycarbonate-based compact discs. 

In a recent paper Pijpers et al. [2.42] have reviewed the application of XPS in the field of catalysis and polymers. Other recent applications of XPS to catalytic problems deal with the selective catalytic reduction of using Pt- and Co-loaded zeolites. Although the Al 2p line (Al from zeolite) and Pt 4/ line interfere strongly, the two oxidation states Pt and Pt " can be distinguished after careful curve-fitting [2.43]. 

Typical applications for nylon include small gears, bearings, bushes, sprockets, housings for power tools, terminal blocks and slide rollers. An important design consideration is that nylon absorbs moisture which can affect its properties and dimensional stability. Glass reinforcement reduces this problem and produces an extremely strong, impact resistant material. Another major application of nylon is in fibres which are notoriously strong. The density of nylon is about 1100 kg/m. ... 

Gi-ind cip some of the acid with soda-lime. and emer with a shallow lityor of the same subst.ince. On heating strongly the smell of plnonol is perceived. 

SO that 0) measures how strongly the solute is solvated in the reference... 

---