Properties 165 strength

It is applied along with traditional methods to test strength properties, hardness, to determine standardized characteristics of stamping, grain size and other structural-sensitive characteristics. 

Kumar A and Meath W J 1992 Dipole oscillator strength properties and dispersion energies for acetylene and benzene Mol. Phys. 75 311... 

Plywood has essentiahy equal stability in both panel directions and is almost as stable as the parent wood in the direction of the wood grain. Strength properties in bending are roughly proportional in each panel direction to the amount of wood in those layers closest to the surface which are parahel to the wood grain direction. Thus as the number of phes increases, these bending properties become more equalized in both panel directions. 

The polymeric products can be made to vary widely in physical properties through controlled variation in the ratios of monomers employed in thek preparation, cross-linking, and control of molecular weight. They share common quaHties of high resistance to chemical and environmental attack, excellent clarity, and attractive strength properties (see Acrylic ester polymers). In addition to acryHc acid itself, methyl, ethyl, butyl, isobutyl, and 2-ethylhexyl acrylates are manufactured on a large scale and are available in better than 98—99% purity (4). They usually contain 10—200 ppm of hydroquinone monomethyl ether as polymerization inhibitor. 

BiaxiaHy oriented films have excellent tensile strength properties and good tear and impact properties. They are especially well regarded for their brilliance and clarity. Essentially all poly(ethylene terephthalate) film is biaxiaHy oriented, and more than 80% of polypropylene film is biaxiaHy oriented. Polystyrene film is oriented, and a lesser amount of polyethylene, polyamide, poly(vinyl chloride), and other polymers are so processed. Some of the specialty films, like polyimides (qv), are also oriented. 

The physical property of primary concern in this appHcation is the transmissivity and, depending on the type of installation, the clogging potential and strength properties. 

Grade G-9, glass fabric with moisture-resistant melamine resin binder, is similar to Grade G-5 but with better electric strength properties under wet conditions. Electrical appHcations should be limited to operating temperatures of 50°C (122°F) or less. 

Grade G-10, glass fabric with epoxy resin binder, has extremely high mechanical strength (flexural, impact, and bonding) at room temperature and good dielectric loss and electric strength properties under both dry and humid conditions. 

A third criterion for the proper formulation of house paints is volume soHds level. Paint with low volume soHds are characterized by poor adhesion and poor exterior durabiUty. A low volume soHds paint film does not have the tensile strength properties necessary for good adhesion found in a higher volume soHds paint (10). Also, any slight dismption or imperfection in the dried paint film or in the appHcation of a low volume soHds paint can result in poor durabiHty properties. 

Table 15. Strength Properties of Phenolic—Carbon-Fiber Composites...

Resins filled with ground limestone to levels of 80% by weight are useful in soHd cast products. The fillers reduce sensitivity to brittle fracture and improve modulus, but have Httle effect on general strength properties (Table 8). 

A high yield chemical pulp, eg, 52—53% bleached yield from softwoods, can be obtained, but strength properties ate inferior to those obtained from the kraft process. If a protector, eg, potassium iodide, is added, an additional 2—3% yield is obtained, as is an improvement in all strength properties. The gas penetration problem can be minimized if ftbetization is accompHshed before treatment with oxygen. Oxygen treatment of virtually all types of semichemical and mechanical pulps has been explored (55). Caustic, sodium bicarbonate, and sodium carbonate have been used as the source of base (56,57). In all cases, the replacement of the kraft by these other processes has not been justified over the alternative of pollution abatement procedures. 

Nickel—rhenium ahoys containing thoria or other additives have been developed for use as cathodes on electrovacuum devices. Rhenium is found to improve the strength properties substantiahy. At 1000°C the strength of a 90 wt % Ni—10% Re ahoy exceeds the strength of a Ni—V cathode material by 90%. Rigidity is exceeded by a factor of 150 to 200%. 

With respect to the action of the enzyme itself, a loss of weight on account of cellulose hydrolysis, as well as loss in strength properties, occurs. Therefore, control of concentrations, temperature, and other processing conditions is important to achieve a product having the proper balance of properties. 

The anatomical stmcture of wood affects strength properties, appearance, resistance to penetration by water and chemicals, resistance to decay, pulp quabty, and the chemical reactivity of wood (5). To use wood most effectively requires a knowledge of not only the amounts of various substances that make up wood, but also how those substances are distributed ia the cell walls. 

Fig. 2. Relatioaship betweea various strength properties of clear wood and moisture content. A, modulus of mpture B, compression paradel to grain C,...

Fig. 5. The immediate effect of temperature on strength properties of clear wood, expressed as percentage of value at 20°C. Trends illustrated are composites from studies on three strength properties modulus of mpture in bending, tensile strength perpendicular to grain, and compressive strength parallel to grain. VariabiUty in reported results is illustrated by the width of the bands. MC = moisture content.

---