Poly Stille

Pd(PPh3)2Cl2 [Stille poly condensation] Pd(PPli3)4 [SuzuM polycondensation]... 

Poly(l, 4-cis-isoprene). Although AHf j is slightly higher than that of polyethylene, it is still completely reasonable for a hydrocarbon. The... 

Vinylidene chloride copolymers were among the first synthetic polymers to be commercialized. Their most valuable property is low permeabiUty to a wide range of gases and vapors. From the beginning in 1939, the word Saran has been used for polymers with high vinylidene chloride content, and it is still a trademark of The Dow Chemical Company in some countries. Sometimes Saran and poly (vinylidene chloride) are used interchangeably in the Hterature. This can lead to confusion because, although Saran includes the homopolymer, only copolymers have commercial importance. The homopolymer, ie, poly (vinylidene chloride), is not commonly used because it is difficult to fabricate. 

The polymers which have stimulated the greatest interest are the polyacetylenes, poly-p-phenylene, poly(p-phenylene sulphide), polypyrrole and poly-1,6-heptadiyne. The mechanisms by which they function are not fully understood, and the materials available to date are still inferior, in terms of conductivity, to most metal conductors. If, however, the differences in density are taken into account, the polymers become comparable with some of the moderately conductive metals. Unfortunately, most of these polymers also have other disadvantages such as improcessability, poor mechanical strength, instability of the doped materials, sensitivity to oxygen, poor storage stability leading to a loss in conductivity, and poor stability in the presence of electrolytes. Whilst many industrial companies have been active in their development (including Allied, BSASF, IBM and Rohm and Haas,) they have to date remained as developmental products. For a further discussion see Chapter 31. 

Mention should be made of the nomenclature for the polymer. Industrially the materially is invariably known in the English-speaking world as polypropylene. However, the lUPAC name for the monomer is propene and until 1975 the recommended lUPAC name was polypropene, a term very rarely used. The latest lUPAC rules base the name of a polymer on the constitutional repeating unit, which in this case is a propylene unit (c.f. a methylene unit for polyethylene) and this leads to the name poly(propylene) (i.e. with brackets). In this volume the more common, unbracketed but still unambiguous name will be used. 

Finally, we want to describe two examples of those isolated polymer chains in a sea of solvent molecules. Polymer chains relax considerably faster in a low-molecular-weight solvent than in melts or glasses. Yet it is still almost impossible to study the conformational relaxation of a polymer chain in solvent using atomistic simulations. However, in many cases it is not the polymer dynamics that is of interest but the structure and dynamics of the solvent around the chain. Often, the first and maybe second solvation shells dominate the solvation. Two recent examples of aqueous and non-aqueous polymer solutions should illustrate this poly(ethylene oxide) (PEO) [31]... 

In the following sections, results from various photoelectron spectroscopy studies of poly(p-pheny enevinylenc), polythiophene, and polyaniline, and their interaction with different metals will be discussed. The intention is not to cover the whole existing literature, but still give a relatively extensive overview, and, where appropriate, give references for further reading. 

For APh-2, on the other hand, the forward ET from Phen to MV2+ was a little slower than that for the poly(A/St/Phen)-MV2+ system i.e., the intensity of the S <- Sj band for the Phen moiety at 510 nm still remained significant for 27 ps after the pulse excitation (Fig. 17) [120]. In striking contrast to the poly(A/St/Phen)-MV2 + system, the APh-2-MV2+ system showed an extremely fast decay in the transient absorbance at 600 nm over the picosecond regime and no subsequent slower decay. The transient absorbance almost completely decayed in 200 ps after the pulse. 

Polyester chemistry is the same as studied by Carothers long ago, but polyester synthesis is still a very active field. New polymers have been very recently or will be soon commercially introduced PTT for fiber applications poly(ethylene naph-thalate) (PEN) for packaging and fiber applications and poly(lactic acid) (PLA), a biopolymer synthesized from renewable resources (corn syrup) introduced by Dow-Cargill for large-scale applications in textile industry and solid-state molding resins. Polyesters with unusual hyperbranched architecture also recently appeared and are claimed to find applications as crosstinkers, surfactants, or processing additives. 

The mechanism of the polymerization of NCA with tertiary amine is still controversial. Mori and Iwatsuki claim that the true initiator is the primary amino group formed by hydrolysis of the NCA with contaminated water and that tertiary amine forms a complex with the NCA and accelerates the addition reaction37 . Harwood et al. confirmed the propagating carbamate by NMR in polymerization initiated with a strong base37 . The successive addition of NCA to the polymer end catalyzed with a strong base affords an alternative procedure for the synthesis of block copolypeptides. Block copolypeptides of poly(oxyethylene) were prepared by triethyl amine catalyzed polymerization of NCA in the presence of poly(oxyethylene)bis-eMoroformate38 . 

---