Chemistry polyesters

All TPE products, irrespective of type, are listed alphabetically by manufacturer s name with the first appearing on the following pages Polyurethane based (PUR or TPU and Polyether or Polyester chemistry) Polyester based... 

We have not attempted to indicate the conditions of temperature, catalyst, solvent, and so on, for these various reactions. For this type of information, references that deal specifically with synthetic polymer chemistry should be consulted. In the next few paragraphs we shall comment on the various routes to polyester formation in the order summarized above and followed in Table 5.3. 

Chemical Properties. The chemistry of 1,4-cyclohexanedimethanol is characteristic of general glycol reactions however, its two primary hydroxyl groups give very rapid reaction rates, especially in polyester synthesis. 

Carboxylic acid hydiazides are prepared from aqueous hydrazine and tfie carboxylic acid, ester, amide, anhydride, or halide. The reaction usually goes poody with the free acid. Esters are generally satisfactory. Acyl halides are particularly reactive, even at room temperature, and form the diacyl derivatives (22), which easily undergo thermal dehydration to 1,3,4-oxadiazoles (23). Diesters give dihydtazides (24) and polyesters such as polyacrylates yield a polyhydrazide (25). The chemistry of carboxyhc hydrazides has been reviewed (83,84). 

R. E. Carpenter, You re in the Chemistry Fusiness Fundamentals of Polyester and Other Chemical Resistant Resins, Ashland Chemical Co., Columbus, Ohio, 1982. 

Blends that contain no nylon can also be prepared by reactive compatibilization. However, interest in these systems has been limited somewhat by lack of control of the reaction pathways. Eor polyester-based systems, epoxide functionaHty appears to be an effective chemistry, involving reaction of the polyester chain ends (183,184). 

During this early period, a very ingenious free-radical route to polyesters was used to introduce weak linkages into the backbones of hydrocarbon polymers and render them susceptible to bio degradabihty (128—131). Copolymerization of ketene acetals with vinyl monomers incorporates an ester linkage into the polymer backbone by rearrangement of the ketene acetal radical as illustrated in equation 13. The ester is a potential site for biological attack. The chemistry has been demonstrated with ethylene (128—131), acryhc acid (132), and styrene (133). 

Liquid organic rubbers with reactive functionality can be prepared by several methods. End-functional oligomers are preferred. Chains attached to the network at only one end do not contribute as much strength to the network as those attached at both ends [34], Urethane chemistry is a handy route to such molecules. A hydroxy-terminated oligomer (commonly a polyester or a polyether) can be reacted with excess diisocyanate, and then with a hydroxy methacrylate to form a reactive toughener [35]. The methacrylate ends undergo copolymerization with the rest of the acrylic monomers. The resulting adhesive is especially effective on poIy(vinyl chloride) shown in Scheme 2. 

Phenolic resins were the first totally synthetic plastics invented. They were commercialized by 1910 [I]. Their history begins before the development of the structural theory of chemistry and even before Kekule had his famous dreams of snakes biting their tails. It commences with Gerhardt s 1853 observations of insoluble resin formation while dehydrating sodium salicylate [2]. These were followed by similar reports on the behavior of salicylic acid derivatives under a variety of reaction conditions by Schroder et al. (1869), Baeyer (1872), Velden (1877), Doebner (1896 and 1898), Speyer (1897) and Baekeland (1909-1912) [3-17]. Many of these early reports appear to involve the formation of phenolic polyesters rather than the phenol-aldehyde resins that we think of today. For... 

Chemical compounds that contain methylol groups (-CH2 OH) form stable, covalent bonds with cellulose fibers. Those compounds are well known and widely used in textile chemistry. Hydrogen bonds with cellulose can be formed in this reaction as well. The treatment of cellulose with methylolmelamine compounds before forming cellulose unsaturated polyesters (UP) composites decreases the moisture pickup and increases the wet strength of reinforced plastic [48,49]. 

Goodman J.A. Rhys, Polyesters—Vol 1, Saturated-Polymers , Am Elsevier, NY (1965) 12) R.F. Gould, Ed, Advances in Chemistry — Advanced Propellant Chemistry , ACS, Washington (1966) 13) D. Haas et a). Binding... 

Polyester chemistry is the same as studied by Carothers long ago, but polyester synthesis is still a very active field. New polymers have been very recently or will be soon commercially introduced PTT for fiber applications poly(ethylene naph-thalate) (PEN) for packaging and fiber applications and poly(lactic acid) (PLA), a biopolymer synthesized from renewable resources (corn syrup) introduced by Dow-Cargill for large-scale applications in textile industry and solid-state molding resins. Polyesters with unusual hyperbranched architecture also recently appeared and are claimed to find applications as crosstinkers, surfactants, or processing additives. 

The reaction between acid chlorides and aliphatic alcohols or phenolic compounds commonly takes place at low to moderate temperature (—10 to 100°C) in solution or by interfacial or dispersion polymerization techniques. It has been widely applied to polyester synthesis. Reviews and books are available on the polymerization techniques as well as on the chemistry of this reaction.2,207 294... 

Table 6.5 Change in titre o/O.OlM NaOH needed to neutralise 50 mg of polyester with relative molar mass of polymer (after H. Batzer and E. Lohse, Introduction to Macromolecular Chemistry , 2nd Edn., John Wiley Sons, Chichester, 1979)...

---