Specifications chemicals/metals

AWS) has issued specifications covering the various filler-metal systems and processes (2), eg, AWS A5.28 which appHes to low alloy steel filler metals for gas-shielded arc welding. A typical specification covers classification of relevant filler metals, chemical composition, mechanical properties, testing procedures, and matters related to manufacture, eg, packaging, identification, and dimensional tolerances. New specifications are issued occasionally, in addition to ca 30 estabUshed specifications. Filler-metal specifications are also issued by the ASME and the Department of Defense (DOD). These specifications are usually similar to the AWS specification, but should be specifically consulted where they apply. 

Because they are weak acids or bases, the iadicators may affect the pH of the sample, especially ia the case of a poorly buffered solution. Variations in the ionic strength or solvent composition, or both, also can produce large uncertainties in pH measurements, presumably caused by changes in the equihbria of the indicator species. Specific chemical reactions also may occur between solutes in the sample and the indicator species to produce appreciable pH errors. Examples of such interferences include binding of the indicator forms by proteins and colloidal substances and direct reaction with sample components, eg, oxidising agents and heavy-metal ions. 

Corrosion also occurs as a result of the conjoint action of physical processes and chemical or electrochemical reactions (1 3). The specific manifestation of corrosion is deterrnined by the physical processes involved. Environmentally induced cracking (EIC) is the failure of a metal in a corrosive environment and under a mechanical stress. The observed cracking and subsequent failure would not occur from either the mechanical stress or the corrosive environment alone. Specific chemical agents cause particular metals to undergo EIC, and mechanical failure occurs below the normal strength (5aeld stress) of the metal. Examples are the failure of brasses in ammonia environments and stainless steels in chloride or caustic environments. 

This is a process that takes place via specific chemical forces, and the process is unique to the adsorbent or adsorbate used. In general, it is studied at temperatures much higher than those of the boiling point of the adsorbate consequently, if supported metals are studied, little or no physical adsorption of the chemisorbing gas takes place on the high surface area support. 

Section 313 requires emissions reporting on the chemical categories listed below, in addition to the specific chemicals listed above. The metal compounds listed below, unless otherwise specified, are defined as including any unique chemical substance that contains the named metal (i.e., antimony, copper, etc.) as part of that chemical s structure. 

The electrolytic processing of concentrated ore to form the metal depends on the specific chemical properties of the metallic compound. To produce aluminum about 2 to 6 percent of purified aluminum oxide is dissolved in ciyolite (sodium alumi-no-fliioride, Na AlF ) at about 960°C. The reduction of the alumina occurs at a carbon (graphite) anode ... 

Thus in all corrosion reactions one (or more) of the reaction products will be an oxidised form of the metal, aquo cations (e.g. Fe (aq.), Fe (aq.)), aquo anions (e.g. HFeO aq.), Fe04"(aq.)), or solid compounds (e.g. Fe(OH)2, Fej04, Fe3 04-H2 0, Fe203-H20), while the other reaction product (or products) will be the reduced form of the non-metal. Corrosion may be regarded, therefore, as a heterogeneous redox reaction at a metal/non-metal interface in which the metal is oxidised and the non-metal is reduced. In the interaction of a metal with a specific non-metal (or non-metals) under specific environmental conditions, the chemical nature of the non-metal, the chemical and physical properties of the reaction products, and the environmental conditions (temperature, pressure, velocity, viscosity, etc.) will clearly be important in determining the form, extent and rate of the reaction. 

In a subsequent section, trace metal movement through some other aquatic systems will be reviewed and analyzed in the context of specific chemical reactions. First, though, the most important chemical reactions of metal ions are reviewed. 

When a metallic material of construction (MOC) is selected to contain, transport, and/or to be exposed to a specific chemical, unless we make a correct, viable, and optimum MOC selection, the hfe expectancy of those facihties, in a given chemical exposure, can be very short. For the inexperienced in this field, the direct capital costs of the MOC facet of the production of chemicals, the funds spent to maintain these facilities (sometimes several times those initial capital costs), the indirect costs that are associated with outages and loss of production, off-quahty product (because of equipment and facility maintenance) as well as from contamination of the product, etc., are many times not even considered, let alone used as one of the major criteria in the selection of that MOC as well as its costs to keep the plant running, i.e., a much overlooked cost figure in the CPI. To emphasize the magnitude and overall economic nature of the direct and indirect (nonproductive) costs/losses that result from the action of corrosion of our metallic facihties, equipment, and the infrastructures, within the United States, Congress has mandated that a survey of the costs of corrosion in the United States be conducted periodically. 

Today, however, carbene complexes covering a broad range of different reactivities have been prepared. Often it is no longer possible to predict whether a carbene complex will behave as an electrophile or as a nucleophile. Thus, a reactivity-based nomenclature would be difficult to apply consistently. For this reason in this book compounds with a carbon-metal double bond will be called carbene complexes or alkylidene complexes , terms not associated with any specific chemical behavior. 

In catalytic reactions, ionic liquids with controllable coordinating strengths and/or reactivities toward the catalyst are particularly important. The coordinating strength of the ionic liquids depends on the nature of the anions and on the metal complex involved in the catalysis. With a large selection of available anions, it is possible to tailor the ionic liquid to suit specific chemical reactions, and variation of the structure and the composition of the cations and anions can alter the solubility of organic reactants in the ionic liquid. 

Finally, for practical reasons it is useful to classify polymeric materials according to where and how they are employed. A common subdivision is that into structural polymers and functional polymers. Structural polymers are characterized by - and are used because of - their good mechanical, thermal, and chemical properties. Hence, they are primarily used as construction materials in addition to or in place of metals, ceramics, or wood in applications like plastics, fibers, films, elastomers, foams, paints, and adhesives. Functional polymers, in contrast, have completely different property profiles, for example, special electrical, optical, or biological properties. They can assume specific chemical or physical functions in devices for microelectronic, biomedical applications, analytics, synthesis, cosmetics, or hygiene. 

Reactivity with Common Materials — This is limited to hazardous reactions with fuels and with common materials of construction such as metal, wood, plastics, cement, and glass. The nature of the hazard, such as severe corrosion or formation of a flammable gas, is described for specific chemicals in Chapter 4. 

---