Solubility Product, Effect

The presence of H+ ions and chloride content, prevents repassivation. The above process generates free acid and the pH value at the bottom of the pit is substantially lowered. It has been measured between 1.5 and 1.0. The pH value depends on the type of steel-values for stainless steel pits which are lower than for mild steel and have a pit pH of 4. This is due to the solubility product effects and depends on the presence of chromium. In stainless steels, the pH is reduced by hydrolysis of Cr + and Fe " " as well as by accumulation of chloride. 

Aqueous ammonia can also behave as a weak base giving hydroxide ions in solution. However, addition of aqueous ammonia to a solution of a cation which normally forms an insoluble hydroxide may not always precipitate the latter, because (a) the ammonia may form a complex ammine with the cation and (b) because the concentration of hydroxide ions available in aqueous ammonia may be insufficient to exceed the solubility product of the cation hydroxide. Effects (a) and (b) may operate simultaneously. The hydroxyl ion concentration of aqueous ammonia can be further reduced by the addition of ammonium chloride hence this mixture can be used to precipitate the hydroxides of, for example, aluminium and chrom-ium(III) but not nickel(II) or cobalt(II). 

Other mixed esters, eg, cellulose acetate valerate [55962-79-3] cellulose propionate valerate [67351-41-17, and cellulose butyrate valerate [53568-56-2] have been prepared by the conventional anhydride sulfuric acid methods (25). Cellulose acetate isobutyrate [67351-38-6] (44) and cellulose propionate isobutyrate [67351-40-0] (45) have been prepared with a 2inc chloride catalyst. Large amounts of catalyst and anhydride are required to provide a soluble product, and special methods of delayed anhydride addition are necessary to produce mixed esters containing the acetate moiety. Mixtures of sulfuric acid and perchloric acid are claimed to be effective catalysts for the preparation of cellulose acetate propionate in dichi oromethane solution at relatively low temperatures (46) however, such acid mixtures are considered too corrosive for large-scale productions. 

It is important to note that the solubility product relation applies with sufficient accuracy for purposes of quantitative analysis only to saturated solutions of slightly soluble electrolytes and with small additions of other salts. In the presence of moderate concentrations of salts, the ionic concentration, and therefore the ionic strength of the solution, will increase. This will, in general, lower the activity coefficients of both ions, and consequently the ionic concentrations (and therefore the solubility) must increase in order to maintain the solubility product constant. This effect, which is most marked when the added electrolyte does not possess an ion in common with the sparingly soluble salt, is termed the salt effect. 

The extent of hydrolysis of (MY)(n 4)+ depends upon the characteristics of the metal ion, and is largely controlled by the solubility product of the metallic hydroxide and, of course, the stability constant of the complex. Thus iron(III) is precipitated as hydroxide (Ksal = 1 x 10 36) in basic solution, but nickel(II), for which the relevant solubility product is 6.5 x 10 l8, remains complexed. Clearly the use of excess EDTA will tend to reduce the effect of hydrolysis in basic solutions. It follows that for each metal ion there exists an optimum pH which will give rise to a maximum value for the apparent stability constant. 

I. Sodium tetraphenylborate Na+ [B(C6H5)4] . This is a useful reagent for potassium the solubility product of the potassium salt is 2.25 x 10 8. Precipitation is usually effected at pH 2 or at pH 6.5 in the presence of EDTA. Rubidium and caesium interfere ammonium ion forms a slightly soluble salt and can be removed by ignition mercury(II) interferes in acid solution but does not do so at pH 6.5 in the presence of EDTA. 

We can gain a quantitative understanding of the common-ion effect by considering how a change in the concentration of one of the ions affects the solubility product. Suppose we have a saturated solution of silver chloride in water ... 

Table 6. Free calcium concentrations in equilibrium with common complexing agents. A low free calcium concentration implies effective complexation, whether the complex formed is soluble or insoluble. The data were derived from either stability constants (soluble complexes) or solubility products (insoluble complexes).

Having introduced matters pertaining to the electrochemical series earlier, it is only relevant that an appraisal is given on some of its applications. The coverage hereunder describes different examples which include aspects of spontaneity of a galvanic cell reaction, feasibility of different species for reaction, criterion of choice of electrodes to form galvanic cells, sacrificial protection, cementation, concentration and tempera lure effects on emf of electrochemical cells, clues on chemical reaction, caution notes on the use of electrochemical series, and finally determination of equilibrium constants and solubility products. 

Figure 12 clearly shows the effect of iron sulfide content of the coal on total conversion and liquid product yield during hydrogenation. The conversion increased from about 52 per cent to 70 per cent using the hot-rod reactor with no added catalyst. The yield of toluene soluble product (oil plus asphaltene) increased from about 30 to 44 per cent with total sulfur increase from 1 to 6.5 per cent. Thus it would appear that iron sulfide can act catalytically in the dry hydrogenation reaction as well as in slurried reactions (15). 

In this paper we have looked firstly at the effect that the catalyst concentration, secondly at the effect that the reactor temperature and finally at the effect that the residence time at temperature have on the chemical structure of the oils (hexane soluble product) produced on hydropyrolysis (dry hydrogenation) of a high volatile bituminous coal. Generally, the hydropyrolysis conditions used in this study resulted in oil yields that were considerably higher than the asphaltene yields and this study has been limited to the effects that the three reaction conditions have on the chemical nature of the oils produced. 

The table also shows the results of experiments with the donors and coal in phenanthrene as solvent. Consistent with the transfer of hydrogen in a radical process, those donors less reactive toward C130 than Tetralin are also less effective than Tetralin in conversion of coal to a phenanthrene-soluble product. However, in contrast to the chemistry of Step 2 we see that those donors that are more reactive toward C130 than Tetralin are also less effective in their action with coal. Thus this simple conversion scheme is suspect. 

If S moles of CaCC>3 dissolve in a liter of water, then S moles each of calcium ion and carbonate ion form. With these ion concentrations equal to S, the solubility of CaCC>3 is calculated as 9.3 x 10 5 M. The higher solubility of magnesium carbonate in water, 6.3 x 10 3 M, results from the larger solubility product constant. Nevertheless, both of these carbonate salts are rather insoluble, and the excess carbonate anions provided by the sodium carbonate effectively precipitate the calcium and magnesium ions from solution. 

Fig. 7.5. The Biopharmaceutics Classification System (BCS) provides a scientific basis for predicting intestinal drug absorption and for identifying the rate-limiting step based on primary biopharmaceutical properties such as solubility and effective intestinal permeability (Pefr). BCS serves as a product control instrument. The BCS divides drugs into four different classes based on their solubility and...

Temperature effects on solubility products are readily assessed as most solubility reactions are clearly seen as endothermic and disorder increasing. Raising the temperature will thus increase Ksp together with the solubility of the solid. 

Electrodes responding to other halides, sulphide, cyanide, silver, lead, copper and cadmium are made using membranes fabricated from pure or doped silver sulphide (Ag2S). The membrane potential is affected by the movement of Ag+ ions between cationic lattice sites which in turn is determined by the activities of the Ag+ ion in the internal and sample solutions. As the activity of the former is fixed, that of the latter alone influences the membrane potential. The electrode will also respond to the presence of S2- ions because of their effect on the Ag+ ion activity via the solubility product expression ... 

There have been many determinations of solubility products for lanthanide fluorides over the years. We shall try to show the range of values presented for a given element, as well as the chemically important variation of solubility with the nature of the metal. Values for aqueous solution will be reviewed first, then the effects of added acid or salts on solubility considered. 

---