Solubility measurement experimental procedure

Although being qualitatively in agreement with experimental results, disagreements between experiment and theory remain. Besides the composition, /a, and the total degree of polymerization, N, all theoretical works refer to the segmental interaction parameter x This parameter can be estimated from a relationship to the solubility parameters. The ODT as a thermodynamic measure of the incompatibility was used to compare a set of symmetrically composed diblock copolymers from different hydrocarbons, polydimethyl-siloxane and poly(ethylene oxide) (PEO) [33]. While the behaviour of hydrocarbon diblock copolymers was successfully described by a consistent set of solubility parameters, this procedure failed for systems containing PEO. The... 

The determination of the purity of a homogeneous solid from solubility measurements is an example of this application of the phase rale. The experimental procedure... 

It is appropriate at this point to briefly discuss the experimental procedures used to determine polymerization rates for both step and radical chain polymerizations. Rp can be experimentally followed by measuring the change in any property that differs for the monomer(s) and polymer, for example, solubility, density, refractive index, and spectral absorption [Collins et al., 1973 Giz et al., 2001 McCaffery, 1970 Stickler, 1987 Yamazoe et al., 2001]. Some techniques are equally useful for step and chain polymerizations, while others are more appropriate for only one or the other. Techniques useful for radical chain polymerizations are generally applicable to ionic chain polymerizations. The utility of any particular technique also depends on its precision and accuracy at low, medium, and high percentages of conversion. Some of the techniques have the inherent advantage of not needing to stop the polymerization to determine the percent conversion, that is, conversion can be followed versus time on the same reaction sample. 

The following experimental techniques were used to measure the pressures and temperatures for solid-liquid-gas equilibrium, phase compositions (bubble and dew points) for gas-liquid equilibrium, and solid solubilities in supercritical pentane. Experimental procedures and the apparatus are described in detail elsewhere (13). 

The procedures outlined above have a practical use, but it should be realized that the parametric models are almost entirely empirical. Experimental uncertainties are also involved since solubility measurements are not very accurate. Solubility loops described by the models only indicate the limits of compatibility and always Include doubtful observations. 

General experiment procedures Normal human dermal fibroblast (NHDF) monolayers were cultured in control medium with or without TGF-p (lOng/ml) or compounds X-Y for 72 hours at 37 °C in humid atmosphere of 95% air and 5% CO2 and labeled with 35S- sulfur during the final 24 hours. The GAG fraction was isolated from both the medium and the fibroblast layer (soluble and insoluble GAGs) and purified by anion exchange chromatography. 35S-radioactivity incorporated into the GAGs was then measured. Experimental tested doses were selected as maximal non toxic doses. 

Although Liu and Millero (1999) presented stabUity constant data for Fe(OH)4 in NaCl media, no analysis of these data has been undertaken in the present review. The experimental procedure adopted to obtain these stability constants was from solubUity measurements of ferrihydrite (Fe(OH)3(s)). It is possible that chloride could have been incorporated into the ferrihydrite structure, as identified by Byrne and Luo (2000), and consequently, the derived hydrolysis and solubility constants may have some inherent error (Stefansson, 2007). 

The diastase activity was traditionally determined according to the Schade method in the earlier years (Schade et al., 1958). One unit of diastase activity (or more specifically, a-amylase), DN, is defined as that amoimt of enz)nne that converts 0.01 g of starch to the prescribed endpoint in 1 h at 37 °C under the experimental conditions. In this assay, a standard solution of starch, which reacts with iodine to produce a color solution, is used as a substrate for honey enzymes under the standard conditions (Rendleman, 2003). A recently developed procedure uses an insoluble, dyed starch substrate (Persano Oddo and Pulcini, 1999). As this substrate is hydrolyzed by ot-amylase, soluble dyed starch fragments are released into solution. After reaction termination and insoluble substrate removal by centrifugation, absorbance of the supernatant solution (at 620 nm) is measured. The absorbance is proportional to the diastase activity. This procedure has been widely adopted in the honey industry due to the convenience of a commercially available substrate and the simple assay format. 

Octanol/water partition coefficients, Pow, which measure the relative solubilities of solutes in octanol and in water, are widely used as descriptors in quantitative structure-activity relationships (QSAR), for example in pharmacological and toxicological applications.49 Since experimental values of these are not always available, a number of procedures for predicting them have been proposed (see references in Brinck et al.).50... 

Sampling and Measurements. The determination of dissolved actinide concentration was started a week after the preparation of solutions and continued periodically for several months until the solubility equilibrium in each solution was attained. Some solutions, in which the solubilities of americium or plutonium were relatively high, were spectrophotometrically analyzed to ascertain the chemical state of dissolved species. For each sample, 0.2 to 1.0 mL of solution was filtered with a Millex-22 syringe filter (0.22 pm pore size) and the actinide concentration determined in a liquid scintillation counter. After filtration with a Millex-22, randomly chosen sample solutions were further filtered with various ultrafilters of different pore sizes in order to determine if different types of filtration would affect the measured concentration. The chemical stability of dissolved species was examined with respect to sorption on surfaces of experimental vials and of filters. The experiment was performed as follows the solution filtered by a Millex-22 was put into a polyethylene vial, stored one day, filtered with a new filter of the same pore size and put into another polyethylene vial. This procedure was repeated twice with two new polyethylene vials and the activities of filtrates were compared. The ultrafiltration was carried out by centrifugation with an appropriate filter holder. The results show that the dissolved species in solution after filtration with Millex-22 (0.22 ym) do not sorb on surfaces of experimental materials and that the actinide concentration is not appreciably changed with decreasing pore size of ultrafilters. The pore size of a filter is estimated from its given Dalton number on the basis of a hardsphere model used in the previous work (20). 

---