Separator monolithic

As a last measure, electrical pre-heating of a small and separate monolith at the inlet of the water-gas shift reactor was assumed, similar to the design of the reformer reactor (Figure 5.59) [389]. The reformer was then operated in the partial oxidation mode rather than under conditions of total oxidation. Through these means. 

Particulate carbon is a carbon material consisting of separated monolithic particles. 

Thinner columns are known to exhibit higher sensitivity and reduced consumption of mobile phase solvent as well as sample substances. In the case of particle-packed columns, with the decrease of diameter of tubes or capillaries, it becomes progressively difficult to pack them with particles uniformly and reproducibly in view of chromatographic separations. Monolithic columns with PEEK clad also suffer from difficulty in manufacturing... 

Work in the area of simultaneous heat and mass transfer has centered on the solution of equations such as 1—18 for cases where the stmcture and properties of a soHd phase must also be considered, as in drying (qv) or adsorption (qv), or where a chemical reaction takes place. Drying simulation (45—47) and drying of foods (48,49) have been particularly active subjects. In the adsorption area the separation of multicomponent fluid mixtures is influenced by comparative rates of diffusion and by interface temperatures (50,51). In the area of reactor studies there has been much interest in monolithic and honeycomb catalytic reactions (52,53) (see Exhaust control, industrial). Eor these kinds of appHcations psychrometric charts for systems other than air—water would be useful. The constmction of such has been considered (54). 

Many grades of interlayer are produced to meet specific length, width, adhesion, stiffness, surface roughness, color (93,94), and other requirements of the laminator and end use. Sheet can be suppHed with vinyl alcohol content from 15 to about 23 wt %, depending on the suppHer and appHcation. A common interlayer thickness for automobile windshields is 0.76 mm, but interlayer used for architectural or aircraft glaring appHcations, for example, may be much thinner or thicker. There are also special grades to bond rear-view mirrors to windshields (95,96) and to adhere the components of solar cells (97,98). Multilayer coextmded sheet, each component of which provides a separate property not possible in monolithic sheet, can also be made (99—101). 

The most widely used exhaust control device consists of a ceramic monolith with a thin-waHed open honeycomb stmcture. The accessible surface of this monolith system is iacreased by applyiag a separate coatiag, a wash coat, of a high surface area material such as gamma-alumiaa with the catalyticaHy active species impregaated iato this washcoat. The catalyst aeeds to oxidize hydrocarboas, coavert CO to CO2, and reduce NO. The whole system forms a catalytic converter that, suitably encased, is placed between the engine and the muffler/silencer unit. 

FIG. 16-55 Adsorbent wheels for gas separation a) horizontal with fixed beds (h) vertical monolith. Reprinted with permission ofUOF.)... 

Burchell, T.D., Judkins, R.R. and Rogers, M.R., A carbon fiber based monolithic adsorbent for gas separation. In Proc. 23rd Biennial Con/, on Carbon, American Carbon Society, 1997, pp. 158 159. 

An integrated circuit (IC) is a monolithic assembly of electrically isolated circuit elements. What this means is that each circuit element is formed on top of, or beneath, other circuit elements to form a compact assembly. Each conductive layer is separated by a non-conducting layer, usually composed of an oxide such as silicon dioxide, Si02- The assembly includes... 

Van Nederkassel, A. M., Aerts, A., Dierick, A., Massart, D. L, Vander Heyden, Y. Fast separations on monolithic silica columns method transfer, robusmess and column ageing for some case smdies. /. Pharm. Biomed. Anal. 2003, 32, 233-249. 

Semiconductor films of ZnO used as operational elements are obtained by oxidation at - 500 - 600°C in the jet of purified oxygen of zinc film deposited at vacuum iP 10 Torr) on substrates made of fused quartz with subsequent sintering at - 350°C at high vacuum conditions [34]. As it was concluded in paper [17] the sintered polycrystalline sample obtained in such a manner should not be considered as a set of various separate crystallites touching each other but rather as a monolithic pattern in which microcrystals with diameter of 1-10 pm are linked with each other by bridges with length and thickness of the order of 0,1 pm (see Fig. 2.4). 

Iberer, G., Hahn, R., and Jungbauer, A., Monoliths as stationary phases for separating biopolymers—fourth-generation chromatography sorbents, LC-GC, 17(11), 998, 1999. 

Xie, S., Svec, F., and Frechet, J.M.J., Rigid porous polyacrylamide-based monolithic columns containing butyl methacrylate as a separation medium for the rapid hydrophobic interaction chromatography of proteins,. Chromatogr. A, 775, 65, 1997. 

Plate type packing to separate the phases is discussed by Carlsson et al. (1983) and by Hatziantoniu etal. (1986). De Vos et al. (1982,1986) describe use of a monolithic porous catalyst with vertical and horizontal channels. The liquid phase flows downward through an array of parallel channels in the monolith, while gas moves in cross flow through a separate set of channels. Another approach treats the catalyst to make part of the surface hydrophobic or lyophobic (Berruti et aL, 1984). The gas phase has direct access to the surface on these unwetted portions of the surface, resulting in partial, spatial segregation of the phases. 

We use the second-dimension separation from Fig. 6.6 with a 25 pL injection volume and 2.5 min sampling time the separation is an RPLC method that uses a monolithic column. Thus, 10 pL/min is the maximum flow rate in the first-dimension. Fig. 6.7 shows the development of the first-dimension column that utilizes a hydrophilic interaction (or HILIC) column for the separation of proteins at decreasing flow rates. The same proteins were separated in Fig. 6.6 (RPLC) and 6.7 (HILIC) and have a reversed elution order, which is known from the basics of HILIC (Alpert, 1990). It is believed that HILIC and RPLC separations are a good pair for 2DLC analysis of proteins as they appear to have dissimilar retention mechanisms, much like those of NPLC and RPLC it has been suggested that HILIC is similar in retention to NPLC (Alpert, 1990). Because the HILIC column used in Fig. 6.7 gave good resolution at 0.1 mL/min and no smaller diameter column was available, the flow was split 10-fold to match the second-dimension requirement... 

---